Please upload more videos sir. I will be waiting for your videos and as soon as you upload I will try it do in ansys. I like the way you teach and especially the theory part. please continue to do this good work. it helps many students like me
@mericbuyukkoyuncu3853 жыл бұрын
Thank you for your nice comments. I will upload more videos. Keep going!
@Ben-dh6in2 жыл бұрын
Just here to say thank you Meric! Good work!
@mericbuyukkoyuncu3852 жыл бұрын
Thank you for your feedback
@martingraupner45622 жыл бұрын
Thank you very much for this great video and explanation! That is very informative. I am still wondering about the last part, why the crack growth is faster with more substeps. This really doesn't make sense physically to me. This means we cannot simulate actual crack growth rates and know when our part is going to break in reality... Would you agree? Thank you very much again.
@xurui93 Жыл бұрын
Auto time stepping has to be on for static crack growth.
@manikumarrekam62763 жыл бұрын
Good to see you again
@mericbuyukkoyuncu3853 жыл бұрын
Thank you for your nice comment
@atifismail3917 ай бұрын
Thanks a lot for your wonderful video. I am following the tutorial to simulate laboratory testing on the rock. Is this possible to study the crack propagation in 2way coupling of structural and fluent? Regards,
@kingdj96693 жыл бұрын
Great work sir, Can you please do some work on recent developments in honeycomb structures.
@gurdenizneser4592 жыл бұрын
How can we make it so that the specimen cracks completely? Also thank you for this video.
@vinayupadhyay48353 жыл бұрын
thank you for the vedio. can you make vedio on boundary condition on sandwich composite plate
@NoName-kv3bh Жыл бұрын
It is a great video sir!!. Can you please explain what all changes we have to make for fatigue crack growth with Paris' law...
@MARCIOROOOTS3 жыл бұрын
Excelent content. Thanks for sharing
@mericbuyukkoyuncu3853 жыл бұрын
Thank you for your nice comment
@a.alshammari31532 жыл бұрын
thank you so much. Could you create explanation video how to compute the triaxiality stress around the crack tip ?
@gokayadabas52193 жыл бұрын
That s another great video!
@mericbuyukkoyuncu3853 жыл бұрын
Thank you !
@joey_joe8557 Жыл бұрын
Hi, Thanks for the video!!!. Could you make a video on crack growth in Pipeline?
@boopathimurugan10072 жыл бұрын
your videos are more informatic and useful. it would be great if u could share the ansys file with us bcz it will helpful for continuous practicing.
@pengch93323 жыл бұрын
great job
@mericbuyukkoyuncu3853 жыл бұрын
Thanks
@blackguardian893 жыл бұрын
Great! Thank you!
@mericbuyukkoyuncu3853 жыл бұрын
Thank you for the comment.
@monikajain5072 жыл бұрын
Good video sir. I have to check crack propagation in post tensioned concrete beam how to simulate that? how to initiate the corner crack or side crack ? Thank you.
@teddykayala653811 ай бұрын
Hello, can you help me ? So, I need to know how to simulate and study crack growth in bearing with ANSYS
@nisharani2617 ай бұрын
Hello sir I have some doubts regarding fatigue analysis
@zeynepbakr27793 жыл бұрын
Very well, thanks
@muhammaduzair12453 жыл бұрын
Great..
@travelfaraway44232 жыл бұрын
Why does the crack grow linear? I would assume an exponential growth because the cross section gets smaller with increased crack?!
@shivnandan6032 жыл бұрын
Thanks you sir... 🙏💐
@shivnandan6032 жыл бұрын
So nice session... 🙏
@franciscogarcia-torres40452 жыл бұрын
Nice video, quite useful by the way. My point is if the same steps you need to use if you are trying to check crack growth analysis under fatigue conditions. What about XFEM method? Anyway, many thanks, I've subscribed.
@aimanhadi24233 жыл бұрын
Great Work! I would very much appreciate if you can explain to us how to calculate the crack opening stress and the maybe singular/non singular stress terms for this example? Thank you in advance
@mericbuyukkoyuncu3853 жыл бұрын
Thank you! Are you asking for hand calculations for critical stress intensity factor or critical stress value for crack growth ?
@aimanhadi24233 жыл бұрын
@@mericbuyukkoyuncu385 Thank you very much for your prompt response. Yes for both i suppose, (or in other words,how can we compare the opening stress for the simulation from ansys with analytical solution?) your explanation would be greatly appreciated.
@mericbuyukkoyuncu3853 жыл бұрын
@@aimanhadi2423 I will upload couple of videos when I have a chance. One of them will be related to analytical calculations
@aimanhadi24233 жыл бұрын
@@mericbuyukkoyuncu385 thank you very much for. I will be looking forward to it.
@user-zh2gb5xd2v3 жыл бұрын
I try to do smart crack for composite material, but it can't work for pre-meshed crack at smart crack. It will appear yellow color. How can I to solve it? Thanks!
@benmeloukaabdelkader7372 жыл бұрын
Thank you for this video, what about arbitrary crack? can you teach us through a video?
@JB-dc3bt Жыл бұрын
Hello, thank you for your great video. I have a question: what you call "fracture toughness", it is rather the "threshold stress intensity factor" right? Bevause your crack did not grow for SIF value below the value you enter in Ansys ("Critical rate")
@md.fahdulwahabchowdhury5118 Жыл бұрын
Can we use it for elasto plastic fracture toughness measurement according to ASTM 1820?
@leninramoscantu47342 жыл бұрын
Hello, I am simulating a crack in the inner surface of a pipe.I followed the steps in your video but the question mark in Smart crack growth is not removed and I don't know what happens. Could you help me with this?. Thanks
@fultonlopez78462 жыл бұрын
awesome, it helped as lot
@lalala39343 жыл бұрын
If I want to make composite material crack propagation. Can use the smart crack ? If not, can give me some methods to do it. Thank you!!
@samjack42362 жыл бұрын
hello sir, can you please make a video on crack propagation in composite with predefined side crack in ansys or matlab? thank you
@Sara-sx5ix Жыл бұрын
What mean K1 K2 K 3 is the mode denoted
@aworindedamilola12882 жыл бұрын
Please do we have smart crack suite in ANSYS 19.2
@Sara-sx5ix Жыл бұрын
Why mode 3 is bigger than mode 1 my anlaysys is in mode 1