I found the math part of this interesting, because I know you are always looking to be more efficient/save time, and you could actually reduce/eliminate most of the measuring. Most of the math isn't even complicated. There are really just two ratios that are going to be relevant - maybe four actually if you count the inverse of those two, but for the most part, just the two. The first one is the pitch itself. You can either divide the pitch out - ex. 5 / 12 = 0.41667 - or just treat it like a fraction. I noticed at one point you were measuring each stud and saw that the differences in length are always 10" - it's a 5/12 pitch, and you have 24" stud spacing, so 5 x 24 / 12 = 10. The difference in length is always double the pitch with 24" spacing. The math also works with any other stud spacing, though the numbers might not be as clean. If you had 16" stud spacing for example, it would be slightly more complicated, but you could still just multiply the 16 by that fraction - ie., 5 x 16 / 12 - and that would be the difference in length from one stud to the next along the same pitch. This works for any other distances, and since it's just a ratio, it works in any units as well (you get the same units out as you put in - inches, feet, centimeters, meters, etc.). The other useful ratio is the length along the roof pitch vs. perpendicular/level length. You calculated this repeatedly with the construction calculator, but if you get the ratio, all you'd have to do is a simple multiply. The Pythagorean Theorem is used for this, and it's a very useful algorithm and worth looking up, but this is the easy version: Divide out the roof pitch, (ex. 5 / 12). Then square that number. Add one. Then square root. The result is the ratio between lengths along the pitch vs. lengths along the ground. It's also actually the ratio between the thickness of a board when it is perpendicular to the ground, vs. how much height it adds when tilted by the roof pitch. In the case of a 5/12 roof, it's 1 5/8" for 2x lumber. Ie., sqrt((5 / 12)^2 + 1) x 1.5 = 1.625

Idk if this is intentional, but if it is well done sir. I just realized my phone has 2 speakers 1 at either end, and when you were on one side of the frame the sound was on the same side. I believe this is a testament to your videography. Whether intended or not I see your skill and hard work you put into the content. Also love your guys taste in music, 90s kids ftw.

Keep it coming 🥳🥳🥳 As always... absolutely fabulous 🥳🥳🥳

Thanks for showing the time spend on teaching and quality conrol (measure twice, cut once). And the occasional oopsie everybody makes, and then corrects themselves. I will never be a framer (Netherlands is brick and cement built mostly), but i love seeing your techniques and ideas.

Always worth it….my boy and I love your channel. Watch it every evening when new vids come out. Good work

Love your videos and your mindset when working, some guys snap lines on the floor and build from that but I like this method better, subscribed!

I love that flush trim router on a stick!

Awesome

The symmetry and coordinated production between you and your swayer is spectacular. I always look forward to your Sat PM videos as I watch them, Sunday morning with my coffee...................very relaxing and rewarding. Could I please ask what is the Yellow/Black hook type thing on your tool belt, behind your right side pouches? Keep up the amazing work!

What’s the name of the App you use to work out your angles? I watch you guys for a refresher and use some of your ideas on my project down under. Do you have an app that converts imperial to metric. Thanks TonyO

what diablo 40teeth blade is he talking about ? im keen on trying it out ! :)

The router with the handle… I need that in my life

Hello from montreal

I see all videos I wanna work same jobs which state you working

My mistake four Weeks out! Happy New Year!!

What’s the song called? or better off what kinda music was on at the start of the video!! That was a slapper!!! I’m guessing 70s era?

Two questions . 1st. Explain the tape on the plate and the tape on the rake calls . What was the saw you used to cut the sheathing .mahalo

Love the 80s music intro lol

When you sheath your walls to the outside corners of the sheathing over lap or is there a gap that's the thickness of the sheathing between the two? As in when a through wall and butt wall meet does the sheathing fon the through wall and butt wall over lap or do they stay separate typically?

So you just get the Level wall height of plans and just add The 5 inch pitch on top?

👍👍

Tim, are you aware that there is only left channel audio sometimes on your videos?

Ok, why 5 top cripples above the window? If the two outside cripples on either side below the window aren't doing anything, what are the two outside top cripples doing structurally? Unless your sheathing edge is hitting there.

Hallo from austria Europa

I would have use 6 inch fasteners in that DBL king to header bond in our jurisdiction. 1:1 for screws 1:1.5 for nails is the rule

Now you need to learn to walk on a rake wall 2 by 4

Where did the other kyle go the One who was always in the video’s

Great video to start my Sunday morning with but I have to say COWBOYS

Reunite Gondwanaland!!

How tall in that Rake Wall???

Agreed Makita stock blades are trash, we spin Diablo in our mak saws also. I’d buy the 91/4 track saw if anyone but Makita made a 9 1/4 blade

Those stock blades from makita do nothing but bind the tool when cutting.

1 fifttie 4

[1:54] Don't blame it on the blade. We can't be changing to fresh blades all the time like we change batteries. I'm beginning to hate cordless saws for anything but quick, rough or secondary work, except maybe for cutting on the roof, esp. sheet. As much as they are hyped all over the internet and everyone is using them now, the truth is they still suck hard compared to corded saws. The power is not even close on the first cut with a fresh battery and the truth is it goes downhill fast no matter what size battery you are running. People talk about going all day or half a day on one--BS. Working Oregon winters in 30-40 degree weather, I am changing even 8ah circular saw batteries pretty regularly. The other day killed four in a row in like ten minutes trying to rip 2x6 with a cordless Milwaukee table saw. Totally useless. We should be going back to corded for another ten years.

Imagine how many less words ewe would have spoken if metric was a real thing. 32 5 and 9 would be 9753.6

Ever nail your foot?

So if you had a triple king would you label it kkk🤣

I think what you actually mean is when you're building your house do what you want with cripples but this is mine so leave me alone? Cause I'm with that.