Soldering Iron Tips - Collin’s Lab Notes

Рет қаралды 207,143

3 жыл бұрын

Equip your soldering iron tips @ adafruit:
www.adafruit.com/?q=Soldering...
It’s important to use the right tool for the job - the tip of your soldering iron is no exception. #soldering #adafruit #collinslabnotes
Visit the Adafruit shop online - www.adafruit.com
-----------------------------------------
LIVE CHAT IS HERE! adafru.it/discord
Adafruit on Instagram: / adafruit
Subscribe to Adafruit on KZfaq: adafru.it/subscribe
New tutorials on the Adafruit Learning System: learn.adafruit.com/
-----------------------------------------

Пікірлер: 40

@keel3r433 Жыл бұрын

"Turn off the soldering iron when not in use" *proceeds to turn it on

@mari-with-a-gun 6 ай бұрын

Opened comments looking for this one

@Gwalchgwyn 5 ай бұрын

@@mari-with-a-gun : You're not alone. >.

@TubeSilva 16 күн бұрын

Same here. Opened the comments to see this. I knew someone would beat me to it. Lol 😂

@acubley 3 жыл бұрын

"It's easy to forget" Sounds like present Collin is giving future Collin an excuse. 😁

@certified-forklifter 3 жыл бұрын

and turns it on while saying it xD nice video.

@MikeBramm 3 жыл бұрын

Also, when done soldering, clean the tip with brass wool as shown. Then clean the tip with tip tinner to remove any impurities followed by brass wool again. Lastly, apply a liberal amount of fresh solder to the tip until it's about to drip, then turn off the iron. Coating the tip with solder will keep it from oxidizing and pitting. I've been doing this for 10+ years and I'm still using my original tips.

@stephendietz1229 3 жыл бұрын

I like the video, but, at the end, when the hand's supposed to be turning the iron off, is it actually being turned on? It could be me.. .🙄

@rpavlik1 3 жыл бұрын

@@stephendietz1229 yep it is

@matambale 3 жыл бұрын

@@stephendietz1229 Which always reminds me of this sketch from the IT Crowd: kzfaq.info/get/bejne/jtN5gtV0yc6doH0.html

@giraffesushi8112 10 ай бұрын

@@stephendietz1229 ever consider that was a bit of subtle humor?

@stephendietz1229 10 ай бұрын

@@giraffesushi8112 Interesting.... is this also an exercise in subtle humor? 😉 Oh no! My life has been a lie for the last 2 years. I need time to think about how it all went wrong. 😔

@jamesthepuerilis 3 жыл бұрын

I don't know if it's just me but i find Collin's voice almost hypnotic, his knowledge and the way he presents shows just keeps me hooked.

@lamboking8able 17 күн бұрын

I love my hoof tip. Thanks for the tips

@darkwinter6028 3 жыл бұрын

I find that with a proper setting on the soldering station, I get better results from a large hoof on small parts than a small tip. I set it just a little above the solder’s melting point, get a tiny dot of solder on the iron to be a heat bridge, and then flow solder into the joint. However, I don’t do anything smaller than 0805s... stuff like SOIC and QFP devices are done with drag soldering. Also, magnification is essential (I’ve got a stereo microscope, but even a desk-mounted magnifying glass helps).

@justin.campbell 3 жыл бұрын

what about his signature curved conical tip?

@vishnuvichu2310 Жыл бұрын

Thankyou very much for uploading this informational video. 👍 (Mudy) Hoof tip is so commonly available over here. If we ask for a soldering iron over here shop keepers will give the hoof. And i have been using it for years it's so bad , no life, and it will damage the circuit board too. I have damaged many more by using this soldering iron. I would like to order pointed one.

@rpavlik1 3 жыл бұрын

I think there's some variant of the hoof tip that's great for drag soldering, has a little dent in it. I don't have one yet though.

@mattstroker3742 2 жыл бұрын

60 watt soldering iron in use here. I find that the hoof form works best for desoldering DC jacks etc. The fine tip never seems to work out for me, not even when desoldering smd components. It just isn't able to transfer enough heat to melt the factory tin. Always have to use flux, then my own bought tin to touch it with so it starts melting. But never by itself.

@nidusa1 Жыл бұрын

hold the side of the conical tip to the pin and not vertically like a pen. Mr. solderfix has videos showing this

@-T.K.- 2 жыл бұрын

How about knife tip? I find it very versatile because I can use it from two directions

@Good_Luck_8619 Жыл бұрын

I got same iron

@Bojornensjover 10 ай бұрын

I have all four types of tips, I basically only use the "fine point" and "hoof".

@Segphalt 2 ай бұрын

Hoof always, just various sizes.

@avgrim7729 2 ай бұрын

What kind for soldering led emitter?

@ClassicalRomance Жыл бұрын

What brand of tips do you recommend? Pelase link us.

@chancecaeden550 6 ай бұрын

What iron do you use?

@0xcrypto 10 ай бұрын

I have the hoof. DIdn't know it was dangerous

@euvo_sound 3 жыл бұрын

I wonder how it is possible to damage smd components with a hoof tip, i mean i always solder smd parts with a hoof tip 😞

@noviardi86 6 ай бұрын

But you are illustrating a turning on the power in the end of the video

@techrazor3280 8 ай бұрын

Yes, its easy to forget to turnoff the iron. I always do that. 😖

@ECMASTERPIECE Жыл бұрын

❤❤❤❤❤🙌🙌🙌🙌🙌👍👍

@computingwithcoffee3907 9 ай бұрын

Remember to turn off the power. Proceeds to turn on the power.😂

@NoEx-Tech 10 ай бұрын

overheating and high voltage damages soldering iron. so you might wanna install a fuse and diode