Wow... I have been rapidly losing brain cells trying to get my lofts to look how I want them. This will definitely be reducing the rate of loss significantly!! Thanks so much for the great info and presentation!
@sunsetengineers2 жыл бұрын
Fantastic tutorial and speaking in general, thank you!
@LearnEverythingAboutDesign Жыл бұрын
Great video! One more tip, if you are lofting surfaces, dragging the endpoint/connector can reduce the end surface profile to a size you want. For example if you know you want to loft between two curves on a complex shape, but in the end you may want to do a boundary fill between sections, you can move the endpoints around limiting the end result while still driving the tangency/curvature continuity.
@jtse09 Жыл бұрын
yes, this is the video that answers all my questions. thank you!!!
@k2them5 жыл бұрын
I Did not know about the "Show All Connectors" and "Edit Connectors" functions inside the Loft Feature. Whenever I'd run into Loft issues of this nature I would end up rolling back and making a 3D sketch with straight lines defining where I wanted the loft to go and use them as "Guide Curves" to constrain the Loft into the shape I wanted. This was not always successful. The Edit Connectors seems like a much simpler solution to this method. Additionally, sometimes I would run into the "Unequal Sketch Entities" error as well and would end up making say... 3 Lofts, instead of using one of these shown methods and making it out of a single one. So thanks for this informative video!
@elihershberger93762 жыл бұрын
Very informative and helpful in saving time in the learning curve.... Thanks!
@ifigetbannedagainyoutubeis20183 жыл бұрын
The show all connectors is a lifesaver wish I knew it before. would've saved me a lot time trying to fix all the relations after using split entities
@timothymolitor47132 жыл бұрын
Great video, clear and concise. Thanks for the help!
@mikebeta2909 Жыл бұрын
Tremendous 🎉vid, thank you so much
@gokulg55210 ай бұрын
Thank you very much. I was in a bit of a fuss on lofting two irregular surfaces, your tutorial saved my day. Thanks again.
@96xpLove Жыл бұрын
Fantastic tools you showed, thank you so much!
@thesuperjed1 Жыл бұрын
Great tips! Thank you 🙏
@mahdisolimani70162 жыл бұрын
Perfect! Really thanks...
@jimbo75774 жыл бұрын
I wish I viewed this video a while ago. Thank you!
@sandhyaprabhu69962 жыл бұрын
I was looking for lofted feature to model drop-in T nut.i tried several times to create a perfect curve with loft but failed to come out with one.thank you so much will try with the features mentioned in the video.
@rushilshah99243 жыл бұрын
I make a lot of two-profile lofts to simulate bent wire routing in wire harnesses. After picking the two profiles, I need to have the following settings as default: - Start/End Constraints -Start constraint: -Normal To Profile -End constraint: -Normal To Profile - Options - Un-check Merge result If I could have these default settings active every time I start SolidWorks it would save me a ton of time!
@free_at_last814111 ай бұрын
Fantastic, thank you very much.
@williamhoward71212 жыл бұрын
Great video, thanks!
@4n2earth225 жыл бұрын
Dell Wone! (reset) Well Done!
@marcerasmus37455 ай бұрын
very helpful, many thanks.
@vishank74 жыл бұрын
This is soooo cool! Awesome work!💎
@Tubepkp Жыл бұрын
Wow!
@ranaaamirmukhtar34153 жыл бұрын
Great work
@kandasamyrajan5 жыл бұрын
Thanks
@albertodesantis7393 жыл бұрын
This was outstanding
@yashsheth83434 жыл бұрын
Very helpful video! 👍
@hughessay13724 жыл бұрын
Very helpful--Thanks!
@giovanniguerrero89513 жыл бұрын
God bless...
@bendhoward8 ай бұрын
That spline fit seems like a pretty ugly hack to me… I’m surprised guide curves were completely left out of this video.