No video
SolidWorks: Worm Gear - Assembly - motion
Рет қаралды 27,993
Күн бұрынSolidWorks: Worm Gear - assembly - motion
Worm gears are constructed of a worm and a gear (sometimes referred to as a worm wheel), with non-parallel, non-intersecting shafts oriented 90 degrees to each other. The worm is analogous to a screw with a V-type thread, and the gear is analogous to a spur gear. The worm is typically the driving component, with the worm’s thread advancing the teeth of the gear.
If you don’t know demands I use in this video, please watch my playlist: Solidworks Tutorial to know more information (nếu bạn không hiểu những lệnh mình sử dụng trong video này, mời bạn xem trong danh sách phát Solidworks Tutorial để tìm hiểu)
Solidworks tutorial
• SOLIDWORKS TUTORIAL
#solidworks #tutorial #gear
Subscribe my channel (please!):
/ @cadtutorialmax
Visit my website (thanks!):
Solidworks tutorial: bit.ly/2LjtMzI
Creo Parametric tutorial: bit.ly/2JFmC5T
My 3D CAD: bit.ly/2XEn1iN
@oadka 29 күн бұрын
Assembly starts at 18:40
@mon.ngon.tu.nhien.2018 5 жыл бұрын
những bài chia sẽ của bạn hay và bổ ích lắm
@sivaprasadbobbili1304 2 жыл бұрын
Thank you...
@diasakimbay1631 10 ай бұрын
how to define pitch of the worm gear in terms of parameters of spur gear?
@nhwahyu 4 жыл бұрын
can you explain more about how to define the size of worm gear based on if i want to use Outer diameter?
@CADTUTORIALmax 4 жыл бұрын
thank you for your comment! outer diameter: d=m(z+2). m is module . z is teeth of gear
@muhammadmuzamil3248 4 жыл бұрын
@@CADTUTORIALmax Hi CAD Tutorial. Would you mind to give the value of module (m) and teeth of gear (z) based on this tutorial?
@CADTUTORIALmax 4 жыл бұрын
@@muhammadmuzamil3248 hello. thank you for watching my video. value of module (m) is 2 and teeth of gear (z) is 60. I hope my video is useful for you!
@wizardhunts8078 Жыл бұрын
Somewhere before 2:39 length of rectangle is 60, but after trimming the dimension is gone. Is that affecting the revolve extrude?
@CADTUTORIALmax Жыл бұрын
Thank you for watching, if you don't move the drawing, the size will not change, to make sure you have 60 parameters to the cut edge, if there is something wrong with the video, please forgive
@jilpatel7789 3 жыл бұрын
how to add part 7 explain plz
@jaredtan547 Жыл бұрын
how to calculate the angle in 12:54 ? my material diameter is 56mm
@CADTUTORIALmax Жыл бұрын
angle = 180/number of teeth
@jaredtan547 Жыл бұрын
@@CADTUTORIALmax how can i know the triple circle diameter ? my worm gear is 56mm. outer diameter: d=m(z+2). m is module . z is teeth of gear outer diameter: 56=56(8+2). m is module . z is teeth of gear so the first outside circle is 66mm , second is 61mm ,and the last one circle is 56mm ?
CIM Design Solution
Рет қаралды 619
Mistermestro
Рет қаралды 18 М.