Chain and Sprocket designing,assembling,Motion Study in Solidworks

No video

Chain and Sprocket designing,assembling,Motion Study in Solidworks

Рет қаралды 137,012

Күн бұрын

This tutorial is for:
1. Designing Chain links
2. Designing Sprocket
3. Designing chain path
4. Designing chain
5. Assembling chain and Sprocket
6. Motion Study
1. A Model Military Tank Motion Animation:
www.youtube.co...
2. Slat Chain Conveyor Design Assembly and Motion Study in Solidworks:
www.youtube.co...
3. Chain and Sprocket designing,assembling,Motion Study in Solidworks:
www.youtube.co...
4. Slat Chain Conveyor in Solidworks/ Motion Study:
www.youtube.co...
5.Tank Tread in Solidworks/Chain Driven Pattern Motion:
www.youtube.co...
1. JPL Mars Science Laboratory The Curiosity Rover design Animation/Motion Study in Solidworks
• JPL Mars Science Labor...
2. How to make a Quadruped Spider Robot in Solidworks | Design,Assembly and Motion Study
• Solidworks tutorial: Q...
3. Model Tank designing Assembly Animation and Motion in Sketchup using MsPhysics Plugin
• Model Tank designing A...
4. A Model Military Tank Motion Animation | Continuous Track | Caterpillar Tank Track Motion Animation
• A Model Military Tank ...
5. Bogie Rocker Arm Mechanism Designing and Motion Study in Solidworks 2013
• Solidworks tutorial: B...
6. V 1.O Delta Robot Designing,Assembling and Motion Study in Solidworks || Solidworks Path Mate motor
• V 1.O Delta Robot Desi...
7. V 1.1 Pick and Place Delta Robot/Parallel Robot Motion Study in Solidworks
• V 1.1 Pick and Place D...
8. V 1.2 Pick and Place Delta Robot/Parallel Robot Motion Study in Solidworks | Event based Motion
• V 1.2 Pick and Place D...

Пікірлер: 56

@user-yy4bv5mb4n 8 күн бұрын

Спасибо. Очень познавательное видео👍

@pankajhiralalpatel4454 5 жыл бұрын

Sir, I just completed the chain and sprocket animation successfully and I was very excited Thanks one again I salute you Jai hind

@SolidworksFunPraveenSingh 5 жыл бұрын

Your Welcome. Jai Hind!

@taiguangguo5384 4 жыл бұрын

You uploaded the data I was looking for. Thank you for sharing your skills.

@SolidworksFunPraveenSingh 4 жыл бұрын

Glad to know that it helped you. Thanks.

@kp-musik2845 6 жыл бұрын

I just finished the tutorial posted by you and the simulation was perfect; Although it can be a bit heavy for the analysis of movement, the behavior is quite real. Thanks for sharing the video and encourage to hang more in the future. Note: Improve the recording quality of the new video tutorials.

@SolidworksFunPraveenSingh 6 жыл бұрын

Thank you! Rightly said,Some improvement is needed in the tutorials. regarding this some efforts are done in the later videos. You can watch them and feel the differences.

@SEAT1960 6 жыл бұрын

The design object is interesting, but if what you want to do is a demonstration of skills is enough, but as a video tutorial it is very bad and confusing. The techniques must be developed in the exact sequence and not as it is becoming fashionable to do it today. If you want to teach, do it well, otherwise clearly indicate that it is a demonstration and save the design steps.

@SolidworksFunPraveenSingh 6 жыл бұрын

Thanks for your suggestion JoseV

@freyferdy 3 жыл бұрын

Thank you for the tutorial it’s very important for me .. thanks a lot

@SolidworksFunPraveenSingh 3 жыл бұрын

Glad it was helpful!

@CustomDesignEngineering 2 жыл бұрын

Nice tutorial

@SolidworksFunPraveenSingh 2 жыл бұрын

Thanks for the appreciation!!

@majdhaddadin9615 5 жыл бұрын

The path of the chain is not a fixed diameter circle in real life.It is in the nature of this mechanism. I don't know if you have applied that in this assembly because it looks like the sprocket is actually driving the chain and not like each is being driven by it's own motor. although you have installed two rotating motors in the motion study.

@SolidworksFunPraveenSingh 5 жыл бұрын

Here the Path drawn using circle,hexagons,some starlight lines are used only for two Purpose: 1. Determining the exact number of chain links of a Particular pitch 2. Placing each chain links at the right position before creating hinge joints and finally going to Solidworks Motion Study Two Motors can be avoided here by using gear mates or Belt Mates but due to some problem in that Two different motors of same RPM were used to simulate the rotation of sprocket. The Main Purpose was actually to simulate a real life Chain Sprocket Motion in Solidworks,that's why all these things are done.It may look a lengthy task but to simulate real life (not advance mates or path mates motor driven) these steps are necessary.

@laurynaspeistaras7163 4 жыл бұрын

@@SolidworksFunPraveenSingh In reality when only one sprocket is driving you would observe quite different view as one side of chain would be on constant tension and other would sag so this one does not simulate real life. It is quite close though

@SolidworksFunPraveenSingh 4 жыл бұрын

@@laurynaspeistaras7163 yes you are right. But since the both sprockets are of same pitch circle diameter so i decided to attach motor to both sprockets just to speed up the calculation.

@celsosuarez2765 6 жыл бұрын

this looks more real, like

@SolidworksFunPraveenSingh 6 жыл бұрын

the main objective was also the same.

@seetharamshahapur154 4 жыл бұрын

Dear sir/madam It would be great if u start recording from primary step that includes each and every part of the assembly. Thank you

@SolidworksFunPraveenSingh 4 жыл бұрын

The Video already starts with Links and Sprocket design (although the design steps are not there but Every feature of design are shown clearly). Assembly and Motion Study also starts from Beginning. Very soon i will upload a new video on same topic with some great detailing. Hope that will Help.

@priyanshpc 4 жыл бұрын

hello sir, it was really helpful but sir I am stuck at the assembly part where when I trying to do the motion study part, my chain revolves around the sprocket, can you please help for the same

@SolidworksFunPraveenSingh 4 жыл бұрын

see the Concept is : 1. Place the Path 2. Create a Chain pattern using the path 3. Make Mid Plane of All Links coincident to the plane of Path 4. Create Hinge Joints between two consecutive links by creating coicident mate using same diameter sketch 5. Dissolve the Chain Pattern 6. Place the Sprockets, orient it properly 7. Then go for Motion study

@pankajhiralalpatel4454 5 жыл бұрын

Sir I follow all your steps and create all components and Parth and assembly I also follow steps to create motion in assembly but only sprockets are rotating chain components does not move with sprocket

@samgrant9565 6 жыл бұрын

This takes a huge amount of time to do!!!! Don't do anything big using this method

@SolidworksFunPraveenSingh 6 жыл бұрын

Actually this was a part of learning. I could do it using simple chain driven pattern and then animate by adjusting key frames. But, I wanted the actual motion study. The real time motion of chain links with sprocket moving under gravity

@pankajhiralalpatel4454 5 жыл бұрын

Sir I have one more question How we create motion of two parallel chain of slat conveyor with pairs of sprockets and slats also. Please make a video on this question Please please please sir Thanks in advance

@sagarchothani660 5 жыл бұрын

the mate between chain path & inner link is not working as the message of overdefine pops out. It says that the entity are fixed and hence the mate cannot be solved

@SolidworksFunPraveenSingh 5 жыл бұрын

It seems that Inner Link is fixed. Check it(right click on the inner link) , and Make it Float and then try.

@rahultak2067 4 жыл бұрын

Hello. I am having problem in simulation of chain and sproket mechanism. Can you help me in that? When I apply gear mate to sprocket and chain bush, It only moves until that bush is on sprocket. When that wrap angle is over, chain and sprocket moves with different speed. I have also tried animation without any mate in chain and sprocket. I have applied rotary motor to sprocket and linear motor to chain. But in this case also the chain moves only for first 2 seconds. After that only Sprocket rotates. Chain stays at his position.

@SolidworksFunPraveenSingh 4 жыл бұрын

To Get the Perfect Result you will have to Assemble and Apply Motion assuming Real life Conditions! Like; 1. Gravity 2. Contacts between Sprocket Teeth and Chain 3. A Hinge Joint between Two Consecutive Chain 4. RPM to Sprocket All these Steps are shown in The Above tutorial, try follow that.

@riqyrizqyandra2206 4 жыл бұрын

sir, when i click the chain path it doesnt want to click whats the problem?

@SolidworksFunPraveenSingh 4 жыл бұрын

Can you tell the time (in this Video) at which you are trying?

@adityasuman5380 4 жыл бұрын

Bro atlest tell how to make it You are just showing the dimensions

@SolidworksFunPraveenSingh 4 жыл бұрын

showing dimensions only just to reduce video length & keep the main focus on assembly & motion study. By the way,i am about to upload a new video (with full detail steps) on chain & sprocket very soon.i will share that link with you. Thanks for watching!

@devincrighton4376 4 жыл бұрын

Very hard to follow without any audio / verbal instructions.

@Abdulkadir.Azimov 6 жыл бұрын

proqram name?

@SolidworksFunPraveenSingh 6 жыл бұрын

Solidworks

@pankajhiralalpatel4454 5 жыл бұрын

I follow all your steps but still I am not generating motion of chain and sprocket mechanism What is the problem Your explanation in this tutorial is very fast and incomplete so I cannot understand how you do this

@SolidworksFunPraveenSingh 5 жыл бұрын

in which step your are having Problem? Design/Assembly or Motion Study? Explain in details.

@pankajhiralalpatel4454 5 жыл бұрын

@@SolidworksFunPraveenSingh Mate functions in assembly So motion not created

@pankajhiralalpatel4454 5 жыл бұрын

Only sprockets are rotating but chain components not move

@SolidworksFunPraveenSingh 5 жыл бұрын

@@pankajhiralalpatel4454 Have you made solid contacts between the Each Chain Link and both the Sprocket?? Before going to motion study, firstly position the chain links and sprocket correctly,ensure that there is no any interference between the chain links and the Sprocket teeth. Also Ensure that,No Chain Links are in Fixed Position...

@pankajhiralalpatel4454 5 жыл бұрын

@@SolidworksFunPraveenSingh Sir, I just completed the chain and sprocket animation successfully and I was very excited Thanks one again I salute you Jai hind

@pankajhiralalpatel4454 5 жыл бұрын

Sir, I am fresher in SOLIDWORKS. I try again and again but results is zero. Give me your mail id so I will send you my drawings and please solve what mistake would be done by me. Thanks in advance

@shalynlee4157 2 жыл бұрын

Arghh, it doesn't work for me. When it comes to motion, every pieces of chain flies away, like being boomed. Eventhough I did mating each other one by one accordingly.

@SolidworksFunPraveenSingh 2 жыл бұрын

Do try with the an updated tutorial of the similar chain sprocket design on the channel, it will be more clear.

@sumayaakther.farhana3286 4 жыл бұрын

Where to join hing?

@SolidworksFunPraveenSingh 4 жыл бұрын

here; Hinge Joint is made just to simulate the Movement between the two links🔗.

@sumayaakther.farhana3286 4 жыл бұрын

@@SolidworksFunPraveenSingh yes .... But where ? Inner to outer sketch 9 Can i meat all hinge with single meat any shortcut ? Thanks

@SolidworksFunPraveenSingh 4 жыл бұрын

Here Hinge Joints are created by coincident mate between two same diameter sketches of "inner & outer links Parts". Since, the hinge joints are created between adjacent sketches. Therefore, No Shortcut is there to create all at once.

@sumayaakther.farhana3286 4 жыл бұрын

@@SolidworksFunPraveenSingh It's nor following the path .... What should i do prnt.sc/t8f2js

@SolidworksFunPraveenSingh 4 жыл бұрын

Before creating coincident mate between each circle sketch, Firstly Make Sure that Circle sketches are of equal diameter. if it won't be of equal diameter, while mating you will see option of Concentric mate but Not Coincident mate!