SpeedyBee Bee35 Build - Part 4 - Betaflight Configuration

Рет қаралды 2,654

2 ай бұрын

This is the fourth episode of my SpeedyBee Bee35 Cinewhoop build. In this video, I go through the Betaflight configuration but unfortunately couldn't go do a test flight yet.
If you would like to see the rest of the build, here is a link to the build series playlist:
• SpeedBee Bee35 Build S...
(this is currently the latest video released for this series. So stay tuned for more of this series!)
-- Components --
If you're interested in purchasing any of the components shown in this build, consider using my affiliate links below.
(I receive a small commission at no extra cost to you, and it helps me make more of these videos)
SpeeedyBee Bee35 Pro/Standard Cinewhoop Frame:
s.click.aliexpress.com/e/_mPF...
SpeedyBee F4 Mini + 35A BLHeli_S ESC Stack:
s.click.aliexpress.com/e/_mrV...
SpeedyBee 2006 1950KV Motors:
s.click.aliexpress.com/e/_mq5...
HappyModel EP2 ExpressLRS Receiver:
s.click.aliexpress.com/e/_mP9...
HQProp T90MMX3 Props:
s.click.aliexpress.com/e/_mLC...
DJI O3 Air Unit
www.dji.com/au/o3-air-unit
-- Bind and Fly Version --
If you like this cinewhoop but not interested in building it from scratch, you can buy the bind and fly here:
s.click.aliexpress.com/e/_mLi...
----------------------------------------
Contact me:
nxp200@gmail.com
If you like my content and wish to support me, please consider joining my patreon:
www.patreon.com/user?u=872035...
Fancy buying me a coffee if my videos have helped you?
www.buymeacoffee.com/nxp200

Пікірлер: 28

@deaafrizal 17 күн бұрын

thanks for this guide, really helped me a lot for newcomer :D

@mertboii3 Ай бұрын

First time building a cinewhoop, thanks for this video. Helped me a lot. I think i couldnt build it without this video :D

@Sonic_Ox 2 ай бұрын

Brilliant series nxp200. Thank you so much for creating this. This is far and away the best Bee35 series on KZfaq in my opinion. I plan to install the 03 Air Unit in mine in early May and it will be complete! I will continue to refer to this series when I have questions. Thanks again for such informative, interesting, and entertaining content. Happy flying amigo 🫡 🍻.

@AZ_LoneWolf81 2 ай бұрын

Thanks man this series inspired me to dive in and start building❤

@kurtzFPV Ай бұрын

You can also set up a second aux channel for throttle and activate air mode only at low throttle rather than using a switch. This helps to keep the quad from getting sucked into the wall if you tap it. I also like to turn crash recovery on in the cli, which briefly throws you into angle mode if you hit something, then straight back to acro.

@nxp200 Ай бұрын

Awesome tips! I do like the crash recovery but forgot about it during this video. I'll have to try out the low throttle air mode! Thanks for the comment!! 👍

@kurtzFPV Ай бұрын

@@nxp200 There's a short video by Crash Gordon on youtube that shows how to do the low throttle air mode if you try it.

@Sohail187 Ай бұрын

Great series bud. Wondering what you think of the tune from the Oscar liang page? Did it fly well or did you have to retune it?

@moriwaky 2 ай бұрын

your builts series of the speedybee bee35 are the most complete on internet. I just finish tunning and flying mine and I am pretty happy with the result, I used a pretune from UAV tech is far better than the speedybee you have used here. I added GPS and meteor led controlled by Pinoi so I can change color or even turn off the leds from the transmitter. My Only mistake was at the begening I was using props out and yaw washout was horrible, I just change to props in and it flies on rails. if you want to add meteor leds to a switch you have to solder the yellow cable of the meteor leds to uart3 and put this lines on CLI: resource SERIAL_TX 3 NONE resource PINIO 2 C10 set pinio_config = 129,1,1,1 set pinio_box = 0,40,255,255

@nxp200 2 ай бұрын

That's awesome to hear you got a great build going! Those extra LED and GPS sound pretty good and I'll definitely give UAV Tech's preset a go! Thanks for your comment and sharing your info. Really appreciate it! 👍

@moriwaky 2 ай бұрын

@@nxp200 and I forget to mention but I screw the o3 unit to the aluminium plate and I didn´t use the 2 screw tpu mount so you can give some room there for the stack. I think speedybee modified wiout warning the alumnium plate a put 4 extra holes that matches bottom holes screws of the o3 unit.

@nxp200 2 ай бұрын

@@moriwaky Ah that's a really good point. Not having to use the TPU and getting more room for the stack if using a different brand/model that's too tall.

@FPV.ExploreScotland 2 ай бұрын

Hi its uav tech have setup for bee 35 ?

@knowledgehacks647 Ай бұрын

Firstime building this speedybee35 thank you for this video..im all set but i dont know how to set my props correct in bee35 do you have pictures or video sir?

@AZ_LoneWolf81 2 ай бұрын

finally got it built and tuned super excited to try it out . what size screws should be used for the props m2x8mm?

@nxp200 2 ай бұрын

Yep. I used m2x8mm for the HQ props I showed in this series. Make sure to double check the screw only expose approx 2mm when fully seated in the prop hub to avoid damage to the motor windings.

@betaodrone 2 ай бұрын

very cool friend, do you have the link to the betaflight configurator, which one are you using?

@nxp200 2 ай бұрын

I'm using version 10.9.0 which you can download here: github.com/betaflight/betaflight-configurator/releases/tag/10.9.0 The install files are down the bottom in the Assets section.

@betaodrone 2 ай бұрын

@@nxp200 Thank you my friend you are 10

@AZ_LoneWolf81 2 ай бұрын

Hey question about the radio settings, if betaflight recognizes my radio inputs sticks/switches do I need to program inputs/mixes in the model settings on the radio? it's a tx16s

@nxp200 2 ай бұрын

Just for standard flight controls such as throttle, yaw, roll, pitch and switches, I don't make input or mixes changes on the controller.

@AZ_LoneWolf81 Ай бұрын

did you ever have any issues with the PID settings that were imported due to the warning in BF?

@nxp200 Ай бұрын

I've only had a very short test flight line of sight. Haven't had time to take it out for a real flight yet to tell if there's any issues, but still far it seems to fly well.

@robertovivar9973 Ай бұрын

If you connected a buzzer to that FC, which uart would it be connected to?

@nxp200 Ай бұрын

There are separate BZ+ and BZ- pads next to UART3 that you can wire a buzzer to.

@SerhiyVoytenko 18 күн бұрын

I think you have the wrong number of poles in the motor tab, shouldn't it be 12?

@nxp200 18 күн бұрын

There are 14 magnets in the motor. So 14 poles. I counted them on the motor and also checked the motor specs on SpeedyBee

@SerhiyVoytenko 18 күн бұрын

@nxp200 Thanks! I installed it wrong. I counted stator poles instead of magnets. If you want to know the truth on the internet, say something blatantly and wait for someone to correct you :)