Thank you friend. Thank you for the idea. One time I will try ..Sorry, I was late to respond to your comment. A few days ago I was a little unwell.

160 oz (a gallon) last 1 hour

Try watching this one : kzfaq.info/get/bejne/odiCYMh3vcrFl2g.html

Maybe this is also useful : kzfaq.info/get/bejne/rquJprV0ncC7qYE.html

The spray gun is slightly modified, for easy operation, and easy setting of fire. kzfaq.info/get/bejne/f9KpmtWYyquRYoU.html

Ok, thanks brother...

Yang penting spray gun, semua bisa. Spray gun fungsinya untuk mengkabutkan oli agar mudah terbakar.

Check this link : kzfaq.info/get/bejne/adl2esVp0NibXXU.html

kzfaq.info/get/bejne/fqqnn9h43Z7ZZ30.html

Tergantung besar kecil api tentunya, mas bro. Kalau api segitu 1 liter oli bisa ±1jam.

I tried to make a very simple one but it works fine. But your idea is very good. Thank's. How about this video, I think it's pretty good : kzfaq.info/get/bejne/odiCYMh3vcrFl2g.html

@@YudiHermanto4H nice. I still wonder why it's not hot enough to melt steel. If they can get blue flames out of a jet engine it's only matter of engineering. If your air ratio in a diesel engine is high enough you get a detonation. I've seen couple of vids claiming they have detonation engines but they were probably not. Altough it sounded like a rocket. I guess you'd need the pressure, pure oxygen or at least to raise the cetane number with 2EHN or similar nitrating compound. Maybe to pre-heat the oil in a copper pipe running through the flame like they do it in Coleman multifuel stoves. Actually that's how I found your vids - while searching for such a micro stove running on waste oil

I don't have a temperature gauge. But it is capable of melting copper. The melting point of copper is 1085'C. Approximate burner temperature over 1200'C.

This one uses diesel oil, it can melt steel rope : kzfaq.info/get/bejne/qamRdJigzbrTiZ8.html

Oli bekas dan kotor, dan tidak dicampur apa2, mas.

It uses used car/motorcycle oil. Can also use diesel fuel.

Diesel fuel : kzfaq.info/get/bejne/qamRdJigzbrTiZ8.html

Used oil : kzfaq.info/get/bejne/odiCYMh3vcrFl2g.html

Smelting furnace using hebel : kzfaq.info/get/bejne/rquJprV0ncC7qYE.html

@@YudiHermanto4H Thanks for all your videos. I appreciate them. I'll watch them later on.

Iya di atas 1000'C, misa melelehkan tembaga, suhu leleh tembaga 1085'C.

Yang biasa mas.

Itu cuman skitar 3mm kalau tidak salah mas.

Tremakasih

Langsung pakai pak, tidak ada yang dimodifikasi. Maaf telat respon nya 🙏🙏🙏😁

Ujung spray gun hanya hangat mas, kan itu untuk lewat angin dan oli, otomatis terdinginkan oleh aliran udara dan oli. Nozzle masih tetap mas, tidak digedein..

@@YudiHermanto4H itu buat lebur logam pipanya meleleh ngak mas,trs mendingan model bulat apa model kaya peluit yang mas buat setelah ini?

@@wijayamotor4976 logam apa mas ? Kalau pakai oli bekas paling mampunya tembaga. Kalau pakai solar mungkin mampu lebur besi. Lebih bagus dan tahan sebenarnya bahan jangan dari besi. Lebih bagus dan mudah dinyalakan yang seperti peluit.

@@YudiHermanto4H cuma mau lebur logam alumunium aja mas,ngak terlalu tinggi titik lelehnya 😁😁 sudah pernah riset lubang burner dari semen mortar mas,ambyar tidak mas kena suhu panas? kalo belum di coba mas 😁😁😁

@@wijayamotor4976 ijin mengikuti idenya y bosku

Ok mas, semoga bermanfaat.

Purbalingga Jateng mas, 0813-3614-0267

Siap mas... Apa kabar, mase...gak pernah wa 😂😂

Nomer e khapus om.... 🤭🤭🤭

Balik pake lpg lagi. Anak2 g bisa nyetelnya... 🤦🤦🤦

Kalau nozzle kecil minimal 25 psi, mas.

@@YudiHermanto4H mantab gan👍👍

Cek video yang lain mas, gampang banget kok bikinnya.