I started woodworking and its so great seeing a "simple" project like this in the night before going to bed. Great work! people like you made me get into woodworking. Thanks for this!

Always nice to see a photo of the finished product at the beginning of the video, so one knows what is being made and if you like it.

Simple yet beautiful! Nice to see that new plane put to use also.

I am a huge fan! Thank you very much for the exceptional work and inspiration!

This is the most satisfying thing I have seen today.

You're mine Is blowing!! I like your vision of new things on simple things!! From: Guatemala!

Lampada minimalista Veramente bella.che cura nella realizzazione!!!👍🏼👍🏼👍🏼

I really like your technique, especially the use of the "rubbed joint", I also use it and it works very well . I was in Seoul many , many years ago, before I was a woodworker, I enjoyed it very much, the food , the sightseeing and most of all the people, very friendly and curious. Thanks for your videos!

Excellent work. Experienced Craftsman make it look easy. Thank you.

Outstanding build and video! Love the attention to detail you took while making the lamp, a true inspiration. Beautiful all around.

Your work is just marvelous and your craftmanship couldn't be better

A pretty and delicate lamp, congratulations!

Great job and all of the videos so peacefull, thank you 😇

I really enjoyed the video. Your work is beautiful!

Very inspired, all you were build, like jusy amazing.. Thanks for the video

Amazing!!!!

So relaxing video 😅

인스타애서 우연히 보고 계속 보고 잇어요ㅠㅠ,,,,, 저도 언젠간 직접 만들어보고 싶은데 ㅠㅠ 너무 멋집니다👍🏼

Wow what a work ❤

Nice job ! 👍👍👍😊

Excelente trabalho, parabéns!!!!

Nice one! 👍

Keren sekali karya anda👍

잘생겼다~~~~

Amazing job as the others my Friend!

goooooood~ job !

Прекрасная работа!👍👏 осталось прикупить пресс-клещи😉

Просто и изящно!

Великолепно и талантливо! Получился достойный предмет интерьера.

So Nice

Exquisite

Nice

Reget sitik langsung di lap.....

👍👍👍

Me encanta

I am a young woodworker and I absolutely love your videos. They’re so inspiring and peaceful to watch. I would love to visit your workshop because it’s amazing. Did you go to school to become so good at furniture making?

Que coisa linda, meu Deus

당연히 외국사람인줄 알았는데 자세히 보니 한국분이시네요. 저도 회사 은퇴하면 목공을 배워서 책상이며 의자 같은거 만들고 싶네요. 참 멋지십니다. 얼마나 배우면 흉내라도 낼 수 있을까요? ㅎㅎ

Fantastique

Your work is so impressive. I just subscribed. The flowering trees are beautiful. Where are you? Best wishes on continued success.

I love your reconstruction and I mostly agree with your points. People should always retain their pride, determinations and integrity ( which many other Asian countries have lost becoming subservient to US commands) . However, as for Chiang Kai-shek , let’s not forget that in Taiwan they had years of white terror and oppression … so much so that now they are removing his statues from public spaces …. And democracy, lately , as shown all its flows .

Is this the first time that you use Lie-Nielsen's router plane (received package in another video)? Fine job as usual.

Amazing work! What type of finish did you use?

top

Very nice! Can I know what oil did you apply?

Hello.. i watched your videos, all are impressive, it was nice. Whats the brand of your sliding table saw... im inlove.. verry acurate.... i have tools but homemade.

I love uuu

Very nice, very calm work. The glue up stage is the most worrying for me; I long ago switched to slow cure epoxy for those assemblies which are complicated - having had other assemblies “dry up” on me when using standard adhesive. This assembly was simple - so normal glue was great. In woodworking, there are usually hundreds of ways of completing a joint, a mortise or whatever. There are also a few bad ways - which normally mean not safe. Every woodworker would have made this lamp in a slightly different way: not better, not worse; just different. I particularly liked the use of the spokes haves to get a great finish on the end grain of the base; it’s a great technique but one which needs practice. As,e for the router plane; I love that way to get a flat bottom to a rabbit, dado or mortise. A couple of ways in which I would have made this lamp differently - the mortise for the square upright. I would have hogged out the majority of the mortise using a router or forstner bit; then chiselled the sides and then router plane on the bottom. If you are chiselling out such a mortise, you should creep up on the sides. If you hog out the mass; with a chisel the same width as the width of the mortise, mark out the finished dimensions of width and length; then mark inside those finished lines by, say, 2mm or 1/16”; then chisel the remainder of the mortise creeping up on those inside lines. When you have done that, you can then chisel to the finished lines. The reason for doing this is that you may/will get the timber checking or splitting on your larger chisel cuts; with this method any such splits should be confined to your inside lines and not the finished lines. It takes a fraction longer but will save you from a potential issue. On that point of chisels and router planes, sharpness of the blades is absolutely key; you will not get the kind of edge that you see on this video with a blade which is less than very, very sharp. However you choose to sharpen your blades, keep it simple. I keep my stones and strop right by my workbench; having them so near means that it’s easy just to sharpen up the secondary bevel. In doing something like the mortise shown here - and in a relatively hard wood like one of the oaks, I would touch up the blades before starting; touch up halfway through and then touch up again before putting the chisels back in their case. Nobody ever chiselled or planed timber and said afterwards “I wish I had sharpened them less”. It was very good to see the internal grooves of the upright and them being used for threading the wire. Well done for that. We all learn from past mistakes and I confess that I have done something very similar to find that the glue has obstructed the channel for the wires. So, I would either set the cable inside the 2 pieces of upright and then glued or use a thin metal tube with a “mouse” and string inside (a mouse in this context is something like a heavy screw or nut or something to which you tied a thin string; you then thread that mouse and string inside the tube, often just using gravity. That means that when assembled, you tie the finished cable to one end of the mouse string and pull the cable through. As I said, no criticism of what this craftsman shows and does; if it works, it’s right.

Nice job!!! What kind of finish for the oak?

Love this! How did drill a hole through the entire length of the pole to run the cables for the light?

Mais lindo resultado. Parabéns pelo trabalho. Desculpe perguntar, a medeira que você usa é muito bonita, qual o nome por favor.

I love the lamp. I have a question about the chairs at the end of this video (12:56). Did you make those? If so, is there a video or plans available?

👏👏👏👏👏👏👏......🇵🇪

Como hizo el olor de palo largo para el cable no vi

Amazing! Do you sell these lamps?

Muy bonita ! Qué medidas tiene ?

Finishing natural oil?

How did you drill such a long hole for the cord?

How long does it take for you to make 1?

조명 부속품 구매처 정보좀 부탁드립니다.

조명 기둥 전선들어가는 구멍 뚫는 영상이 없네요...

Can you tell me the dimensions on the pole and base?

Sao lâu quá không lên video bạn ( VIET NAM )