SSL 12 Software Tutorial | SSL 360 - Routing, Settings & More

Рет қаралды 2,539

Күн бұрын

Пікірлер: 44

@Alexandra-Rex 19 күн бұрын

Excellent video while I look at different interfaces to figure out which one to go for. SSL 12 is probably the one I'll go for.

@woodyardmusic 19 күн бұрын

It’s my favorite that I’ve had! Perfect balance of quality, functions and ease of use

@juniorrabello878 21 күн бұрын

Thank man ! Great Video !

@woodyardmusic 20 күн бұрын

Thanks!

@RichRich-b5z 25 күн бұрын

Very informative. Thank you!

@woodyardmusic 25 күн бұрын

You're welcome!

@John-vw4vg 3 ай бұрын

Great video, thanks for this information!!

@woodyardmusic 3 ай бұрын

You’re welcome!

@dvsm 2 ай бұрын

awesome tutorial. I've seen that the ssl2+ can be use as live monitoring / stand alone mixing (with laptop off), just using it for getting power. Seems that ssl12 can be run only with ssl360, have you tried to use it as stand alone / direct monitoring ? once again thanks for your videos.

@woodyardmusic 2 ай бұрын

I’ve not tried that! I don’t think the SSL12 would work too well for that. It’s a lot more complex and lots of the routing and monitoring can only be configured in the software. The SSL2+ literally just has that blend knob which makes it a lot easier for that standalone workflow.

@fcwy1 3 ай бұрын

Thanks. Really good tutorial!!

@woodyardmusic 3 ай бұрын

Thank you!!

@metomett 3 күн бұрын

hey there. Can't find an answer to my question...Is the interface keeps last loaded profile once it is turned off and then back turned on again...can I setup the routing on my Mac true the 360 app, disconnect the SSL, connect to my iPad and still using the same profile/routing ?

@woodyardmusic 3 күн бұрын

That’s a great question! To the best of my knowledge, the profile stays. As far as iPad, I don’t know, I don’t have an iPad that takes usb-c so I can’t test it.

@metomett 3 күн бұрын

@@woodyardmusic thanks for the answer . Great review by the way

@ahzootube 2 ай бұрын

I am having troubles with syncing via midi cables. There are 12 ports etc. but it does not connect to hardware.

@woodyardmusic 2 ай бұрын

I haven’t tried it with midi yet, definitely something I plan on doing in the future though!

@vexlerorly Ай бұрын

Hay On some of my chanels the peak bars are red instad of green Whay is it?

@woodyardmusic Ай бұрын

That means either your input signal or output signal is too hot. If it’s happening on the input channels, turn the input gain down. If it’s happening on the output channels, (headphones for example) then send less audio to that output

@vexlerorly Ай бұрын

@@woodyardmusic in the input only on chanel 1. 2-4 are grean with the same microphone. On the output the headphones and the master are red and line 3/4 is green

@ezurg01 Ай бұрын

questio n on the adat on the manual it says it can only be a slave interface because I have a 18i20 and the only way I can get hem to synce is if the scarleet is the master and the ssk the slave ?? i have no problem doing that but would I be loosing quality haveing the scarlet be that master clock???

@woodyardmusic Ай бұрын

That’s odd, I actually use an 18i20 with the SSL myself. I’ll have to take a look at the setting on both to see what’s happening. I haven’t noticed any loss of quality though, it always sounds pristine

@ezurg01 Ай бұрын

@@woodyardmusic mine is a gen 2 maybe that’s why? Don’t really know been struggling to get them to synced with the ssl 12 being the master

@woodyardmusic Ай бұрын

@@ezurg01 ⁠it’s possible because it’s older that it’s harder for vit to play nice. I had two 18i20s and it was even hard to get those two to connect though. I know you have to go into Focusrite control and get all of those settings right too

@StratsRUs 2 ай бұрын

Do you have this as a separate App along with Logic on your Mac ? Thanks, is there anything to watch out for also with Logic ? Would I get a doubling in sound from a guitar etc , that I would have to deal with ?

@woodyardmusic 2 ай бұрын

Hello, yes this is a separate app that comes with the SSL12. You can use it to configure the interface regardless of the DAW you’re recording in. To avoid doubling, just make sure you’re monitoring in either Logic OR SSL360, not both, just pick one 😁

@Acidental 2 ай бұрын

Hello! Is it possible make reamp from te OUT LINE to the Analog Input?

@woodyardmusic 2 ай бұрын

Yeah, I haven’t tried it but it should work. There’s plenty of routing options and I think you can even toggle the output between balanaced and unbalanced. I’d still recommend a reamp box or something to make sure you get the level and impedance correct though

@Acidental 2 ай бұрын

@@woodyardmusic Awesome! Many Thanks!

@thehauntedyouth666 27 күн бұрын

Hi, i'm having an issue where my input and playback monitoring plays on top of one another, like creating a doubled delayed effect when recording with a bit of latency... I just wanna hear output monitoring through speakers and headphones... Can't turn it off anywhere it seems, and nobody seems to talk about this problem, which is a huge downer. what do i miss here? Kind Regards Joachim

@woodyardmusic 27 күн бұрын

Hello! It sounds like you’re hearing playback from both the interface and the DAW, one of them needs to be turned off. Are you using Logic or a different DAW?

@thehauntedyouth666 27 күн бұрын

@@woodyardmusic I'm using Ableton

@thehauntedyouth666 27 күн бұрын

@@woodyardmusic My old focusrite had a switch from playback to input, It's weird SSL oversaw a simple but important feature in this line

@woodyardmusic 26 күн бұрын

@@thehauntedyouth666if I had to guess, it sounds like input monitoring is turned on in Ableton, which is routing it through the “playback” of your interface. you then hear this up against the slightly faster sound of the interface input monitoring which causes that awful latency sound. I’d recommend turning off the input monitoring in Ableton or turning off the input monitoring on the SSL, either way with the goal of having only one input monitoring occurring. That should fix the issue if I’m following correctly

@ereiffman 25 күн бұрын

I've actually been having this exact issue. I'm able to mute the DAW playback, but then the interface volume isn't so loud. I haven't yet figured out how to mute the interface and not the DAW. Although this video should help