Reassembling the engine components and starting the engine.
Пікірлер: 47
@joyridaz2 жыл бұрын
Noooo. Don’t stop there… now that I know it can run we need to see it on the road! Why? Cause I need some inspiration on how to address my rust bucket, specifically frame repairs. Awesome job! Was so suspenseful with the fire, the audible changes in engine sounds as it got closer and closer to running. Really neat trick with the liquid metal on the manifold, I’ll need to give that a try
@HumbleAcres2 жыл бұрын
Don't worry there will be more.
@fstoll32 жыл бұрын
Are you getting enough sleep? Your voice sounds tired. Hope everything is well. Enjoy your videos. Keep up the good work.
@HumbleAcres2 жыл бұрын
I'm doing good. Thanks for asking.
@joyridaz2 жыл бұрын
Pinhead has an awesome in depth tutorial series on rebuilding the carb, I’m a total dope and I’ve successfully rebuilt two landcruiser carbs following his lead. Grt work on getting this old piggie going again! Keep the videos soming
@jimryan5724 Жыл бұрын
Very interesting
@Steventhedieseltechapprentice2 жыл бұрын
It’s almost that time of the year. I’m looking forward to more videos with the John Deere A! Good job getting the Toyota running again!
@phillipdickinson85572 жыл бұрын
You can't stop there let's keep going we got more to fix and adjustments to make we got this video is turffic loved it but we can't stop we got to go over the top never miss a video can't wait for next one as always thanks for sharing and your time was really great.
@philipstreechon45232 жыл бұрын
Fill the carb with gas thru the vent pipe (pipe / tube sticking out at the top of carb at at a angle) close choke crank over and pump the gas it will start if all else is correct
@HumbleAcres2 жыл бұрын
I did fill the bowl how you described. Hard to show everything.
@chrisduggins34352 жыл бұрын
Soak cork gaskets in hot water if they shrink, then glue it to the valve cover
@sawisfamily12 жыл бұрын
You got it! ✌🏼
@miguelarteaga64652 жыл бұрын
Epic videos on The FJ ----keep'em coming !
@HumbleAcres2 жыл бұрын
There is some good stuff coming, Stay tuned!
@genegoodman40532 жыл бұрын
Use Rd blue form a gasket or get a rubber gasket and glue it to the valve cover not to the engine
@HumbleAcres2 жыл бұрын
I will look into it. Thanks!
@oisin1980 Жыл бұрын
I really enjoyed this land cruiser series. Your fantastic. Thank you so much for the time you put in. I would bring my car to you anytime. Pity your not in Ireland 🙃
@HumbleAcres Жыл бұрын
Glad you enjoyed it!
@chriscampbell23272 жыл бұрын
It is alive! Great job getting it running, all you you need is to hook a gas can and maybe you van get it to run long to get the timing and carb right.
@HumbleAcres2 жыл бұрын
Ya that would be good. I realized when I was editing that I never adjusted the carb, so the would probable help.
@cyberburnzy Жыл бұрын
I think the ball on the flywheel represents the factory advance of 7' if you keep turning just a little you should see a faint line representing TDC. And congrats on getting it started!
@HumbleAcres Жыл бұрын
I believe you are correct
@sshyshy6097 Жыл бұрын
I'm going to subscribe I love your in depth video!
@HumbleAcres Жыл бұрын
Thanks 😊
@stormcloud30272 жыл бұрын
Absolutely awesome definitely enjoyed it, full view and thumbs up,,👍
@HumbleAcres2 жыл бұрын
Thanks!
@theowiththeo2 жыл бұрын
:) nice! maybe larger gage wire! keep it up!
@kenw25422 жыл бұрын
If cork gaskets dry out and shrink, soak the Mina light oil overnight. This will obviously squeeze out when you tighten them down causing them to look like they are leaking so a little patience and clean rags will be required. Plus and active or robotic arm of coarse.
@HumbleAcres2 жыл бұрын
Awesome! Thanks for the advise!
@georgemarshall75082 жыл бұрын
Loosen the upper and lower part of intake that helps when tightening it up to head to make it even.
@georgemarshall75082 жыл бұрын
I'm watching another one of your videos,did you try different ways to install the valve cover gasket,such as flip it over or swap ends.like your videos have a good day.
@moneysaversilver Жыл бұрын
If you get backfire your timing is off usually 180 out
@TylersNeighborhoodGarage2 жыл бұрын
The reason the GM distributor fits is that the Toyota F engine is a loose copy of an old GMC straight six. Note that I said GMC, not Chevrolet. Up through the early 60's Chevrolet and GMC engines were different designs, with the GMC being notably more heavy duty, with pressurized oiling and such.
@robertshatto29952 жыл бұрын
Yeppers,,soak cork gasgets in oil..it will fit,and the oil will push out when it gets tightened down,,,and if you don't know,,you don't know,,,no big deal,,I ran it to that when I was in high school,,I told my shop instructor, this ford was kicking my ass,I can get these cork gasgets to fit, he told ne the ole trick of soaking them in oil,,,
@pieman7522 Жыл бұрын
I have a fj40 and it needs a lot of work
@HumbleAcres Жыл бұрын
Join the club. lol
@robertshatto29952 жыл бұрын
And try to invest in a ultra sonic cleaner,,I got mine on amazon,,and I just use Dawn dish soap,,
@HumbleAcres2 жыл бұрын
Ya I need to look into getting one.
@kenw25422 жыл бұрын
Soak gasket of cork oi oil overnight. It’s just got too dry.
@jamesmorrison18842 жыл бұрын
Hello she fires did you have gas connected to it? I know break cleaner works but quick start works better. I would think it would need a minute maybe running get the oil going since you changed oil and need time fill up oil filter. I have put a bottle gas and let gravity feed into carb. Watch out fire been there lol. Have a great day.
@HumbleAcres2 жыл бұрын
I filled the carb bowl with gas. In the end of the video it might have ran out.
@jamesmorrison18842 жыл бұрын
@@HumbleAcres Great job getting it started did the oil presser build up
@jamesmorrison18842 жыл бұрын
@@HumbleAcres pressure
@joesixpack75512 жыл бұрын
WHAT!!! You can't just leave us hanging on this... You need to get it running well enough to get to Home Depot with it. You know if you just abandon it now, it will never be driveable.
@HumbleAcres2 жыл бұрын
Video coming soon😉
@williamlane91402 жыл бұрын
Omg!! I'm screaming at your video. Advance your timing and give it fuel!!