Steampunk Skull Lighter DIY

Рет қаралды 18,601

5 жыл бұрын

Thank you for watching! To see more of my work, please check out my Instagram / ivanternyuk
I receive a commission (at no extra cost to you) if you make a purchase after clicking one of the affiliate links below.
Here are materials and tools used in this video:
Dremel 4000:
amzn.to/2KztroF
Dremel 225-01 Flex Shaft Attachment:
amzn.to/2KjASEt
Dremel 4486 MultiPro Keyless Chuck:
amzn.to/2KB6TnF
Dremel 710-08 All-Purpose Rotary Accessory Kit:
amzn.to/2KpiWbL
Dremel Fine and Coarse Detail Abrasive Brush:
amzn.to/2vOtDeg
PPFISH Brass Pill Holder:
amzn.to/2ShMebu
Malleable Brass Flat Top Sign Standoffs:
amzn.to/2PaObo8
Glintbay Creative Handmade Brass Skull:
amzn.to/2KHIA8d
Brass Solid Round Rod:
amzn.to/2KH4WGY
#steampunk
#DIY

Пікірлер: 27

@BennySime 5 жыл бұрын

Awesome video. Thanks for sharing

@MrGoodCat 5 жыл бұрын

Thank you!

@niltonsilvia7496 5 жыл бұрын

Show de bola.. espetacular esse isqueiro. Parabéns. City Bragança Paulista. Brasil.

@sharpblade9099 3 жыл бұрын

Crazy💙

@MrGoodCat 3 жыл бұрын

Thank you for watching!

@ivant1174 5 жыл бұрын

Excellent

@MrGoodCat 5 жыл бұрын

thank you!

@WILFRED1184 4 жыл бұрын

You should get some flux. It will make soldering much easier and cleaner. Don't get the water soluble stuff though it sucks. Get rosin or acid flux it works much better.

@MrGoodCat 4 жыл бұрын

Thank you, but that's exactly what I use

@nexusrnah6418 4 жыл бұрын

Amazing job with almost no tool!

@MrGoodCat 4 жыл бұрын

Thank you!

@cristiangomez6063 5 жыл бұрын

Some steps were too complex than they needed too, but over al looks amazing

@MrGoodCat 5 жыл бұрын

Thank you!

@alpertintas4771 5 жыл бұрын

good job ,could you tell me the type of solder wire please

@MrGoodCat 5 жыл бұрын

Thank you! I like to use plumbing led free solder, you can find it at your local hardware store, or amazon.

@alpertintas4771 5 жыл бұрын

@@MrGoodCat thanks a lot

@MrGoodCat 5 жыл бұрын

Thank you for watching!

@mohammadmistarihi4029 3 жыл бұрын

Amazing, what parts of brass did you used to make the lighter body??

@MrGoodCat 3 жыл бұрын

Thank you for watching! That was a big challenge, to find all the parts, i just found bunch of different brass parts on Amazon, then just had to pull it together

@mohammadmistarihi4029 3 жыл бұрын

Mr GoodCat i made few brass lighters but with different parts , keep it up 👍

@MrGoodCat 3 жыл бұрын

Thank you!

@princefriendship 4 жыл бұрын

From where you got striker wheel, and spring for flint?

@MrGoodCat 4 жыл бұрын

Any Zippo lighter, you will have to take it apart

@dordenlequin4389 4 жыл бұрын

Wooowwww . If you sell that how much ? I hope i had one . From philippines

@MrGoodCat 4 жыл бұрын

Thank you for watching! Make sure to subscribe, I will give away some of my stuff for free to my subscribers

@kubach21chmielewski54 4 жыл бұрын

Jak się nazywa metoda łączenia metalu z palnikiem co trzeba kupić do.takich rzeczy? Zapalniczka bardzo.stylowa

@MrGoodCat 4 жыл бұрын

Thank you friend. I dont speak polish, but i can understand it. Its called soldering, you need flux solder and a torch. This method is used for metals like copper or brass in my case.