Great comparison, I went with RCI aluminum plates on my 2020 Ford FX4 as I mostly drive desert trails in Az and same type of off-roading in Idaho/Montana. i don't do any rock crawling so I do like the weight savings.
@RogueOverland3 жыл бұрын
Thanks for sharing!
@patrickkelly97213 жыл бұрын
I don't intentionally pound my 4runner. For me the armor is to deflect objects flung up into the underside. I prefer carefully picking a line that avoids damage rather than bulling my way through. Aluminum for me.
@RogueOverland3 жыл бұрын
Makes sense! Thanks for the input.
@AGR8SKP4 жыл бұрын
Had to turn my sound up quite a bit to hear you.
@RogueOverland4 жыл бұрын
Thanks for the feedback! We will make sure you pay more attention to the sound level on our next video.
@bicdut3 жыл бұрын
@@Atlanta_Cyclist I gotta ask what's a fart fan?
@JPJamster2 жыл бұрын
Great video,you raised very important points that I had not thought about like how each material reacts to sliding over rocks. Thank you !
@RogueOverland2 жыл бұрын
Happy to help! Thanks for watching.
@RaysVideoChannel12 жыл бұрын
I just got done switching mine from aluminum to steel. I went with aluminum originally because I’m mostly a trail and not a rock crawler type driver. That said I do occasionally find myself on a rocky trail. What I didn’t understand is that unless you are willing to turn around (if you can that is) at the first sign of rock obstacles you are going to use your skid plates. Maybe not a lot but they will get used. And it doesn’t take much of a hit to damage an aluminum skid. While they will protect the underside, they will get bent up until they don’t fit well. The truck is just too heavy for aluminum. My advise now is if you are going to actually use your vehicle off road get steel. The weight difference is only 60-70 lbs. is just not enough to justify going with skids that will not last.
@RogueOverland2 жыл бұрын
Good point! Thanks for watching.
@markbristol26454 жыл бұрын
On my 2006 X I just went all steel as I tend to be a cheapskate. My truck gets real bad mileage so I really don't think anything but a lighter right foot has any noticeable effect on fuel economy or lack of it. I don't drop skids for oil change. I put a ball valve oil plug in engine and it has a hose barb on it so I attache a 1/2 inch hose and it is very neat and clean. In the radiator skid I made an aluminum trough that goes under the oil filter so all the oil goes out the access hole in the skid. I never flush trans. Scotty Kilmer's video on why just dump and fill is the best route is invaluable. I just suck the trans fluid out the fill tube with a big hypodermic with a 1/4 inch hose attached and refill. Thanks for your excellent videos.
@RogueOverland4 жыл бұрын
Good info, thanks for commenting!
@TheTattooedRonin3 жыл бұрын
good info bro! For my Subaru I rarely ever take it off road anywhere. Mainly just like trails so I would like some protection but dont plan on going anywhere crazy with it since its my daily driver and still new lol.
@RogueOverland3 жыл бұрын
Thanks. Sounds like you would get away with the factory skids or aluminum.
@sixoh_diesel56623 жыл бұрын
Good info, was searching and found this video. This is the type of info I was looking for. Looking at a GXOR build and weight will be a factor, though I'm more concerned about weight up top than down low.
@RogueOverland3 жыл бұрын
Glad the video helped. Thanks for watching! We agree that weight up top is more of a concern than weight down low.
@jayrobinz79354 жыл бұрын
Steel for me. it's amazing how many deep gouges there are, they definitely take a bashing. When I took them off after Soda Lake to re-powder coat , all of them went on smooth , Except the Radiator skid that needed some persuasion lol , Great Video as always
@RogueOverland4 жыл бұрын
Thanks for watching an for the input on your experience.
@1TexasKid2 жыл бұрын
Thanks for the information. This is information you can’t find on the web. Valuable. I was looking to install my own skid plate for the purposes of protecting my catalytic converter on my 2019 Honda CR-V. Now it’s not a 4X4. Price wise, a catalytic converter shield or a skid plate will cost the about the same amount of money if I decide to pay a dealer for installing it. Thanks again the video help me out a lot.
@RogueOverland2 жыл бұрын
Glad to help!
@ElleryBaker3 жыл бұрын
Good analysis and summary. I’ve bent my steel tcase skid on my JKU Rubi while rock crawling. An aluminum skid would’ve had awful results. You’re spot on too with the fact the aluminum will grab more. Unless one is seriously concerned about weight for some reason or really just a mall crawler in reality, steel is almost always the way to go with skids. Hit them with some rustoleum after every trip and you’ll be good for a very long time.
@RogueOverland3 жыл бұрын
Thanks for sharing your thoughts!
@joer61274 жыл бұрын
i just installed the RCI aluminum skid packaged on my 2020 Tacoma. The truck is a work truck i drive around several rock quarries its more for a piece of mind then anything but i do occasionally hit the trail but i dont ever plan to actually take the truck rock crawling. So the weight savings was the big factor for me. If i run into issues down the road ill swap the front plate out for a steel plate and keep the trans and t-case as aluminum. Anything is an upgrade over the stock ones.
@RogueOverland3 жыл бұрын
Thanks for the input!
@KairyuRider3 ай бұрын
Looking at steel vs aluminum for my motorcycle. But in this case I actually am Looking at stainless steel. Seems the best of both worlds. Lighter than mild steel, less corrosion than aluminum, very rigid over time
@RogueOverland3 ай бұрын
Thanks for the comment! It seems to make a lot of sense on a motorcycle to strive to keep weight down. The polymer skid plates like AXP seem good, we have had great results on our dirt bikes.
@KairyuRider3 ай бұрын
@RogueOverland I prefer plastic, but only 1 company makes for mine and there are too many design flows to trust it. (I say that as a custom bike biulder) So for not I'll trust a stainless plate
@michaelmullins79204 жыл бұрын
I liked your video but have a couple of comments. I'm not interested in Rock Crawling so I have leaned towards Aluminum for most but not all of my armor. I do have steel rock sliders, rear differentials skid, shock bottom skid, and lower link skid all steel. In your video you made it sound like all skid plates have to be removed to change the oil and that's not true some have access doors for the drain plug and filter like CBI and others. While wildy expensive I would have liked to hear you mention the Artec Industries 6061 grade Aluminum skids versus the industry standard grade 5052 Aluminum.
@RogueOverland2 жыл бұрын
Good points. Thanks for the comment.
@GeorgeToft4 жыл бұрын
You're a funny guy. Worrying about gas mileage on these trucks? Thanks for doing the review. I had heard about aluminum skids and didn't know the difference. You did a good job comparing and contrasting the two and I'm really happy I have steel plates. And I'm not even going to consider aluminum now.
@RogueOverland4 жыл бұрын
lol..... we don't worry about MPGs but some people do. Glad you enjoyed the video. You'll be happy with the steel if you wheel! Thank you for watching!
@GeorgeToft4 жыл бұрын
@@RogueOverland I got the steel skid plates last year. Four of them. Added 160 lb to the truck.
@mxsmotosportvideo3 жыл бұрын
Depending on the trails you go, weight will also be a factor. At last Installed steel skid as aluminium got stuck many times & bends, didn't worked well on Rocky trails
@RogueOverland3 жыл бұрын
Well said. Thanks for the input! Be sure to check out our other KZfaq videos.!
@barefooboy174 жыл бұрын
Just installed a steel engine skid the other day on my Xterra from Shrockworks. It mounted well, looks and feels solid. I haven't been on the trails with it yet but I think it will hold up great
@RogueOverland4 жыл бұрын
Very nice! They make great stuff. Thanks for watching and commenting.
@4wdaddict412 жыл бұрын
Got shrockworks on my 3rd gen too ! It looks tuff
@MC4D.3 жыл бұрын
What about skid plates with service access holes? Is it a good idea or just go for a solid no service hole plate? It'll be for mild overlanding. Dirt roads possible uneven trails.
@RogueOverland3 жыл бұрын
Service holes seem fine to us. Sometime the fluid gets all over the top side of the plate, so we usually just pull the skid plates when we do service anyway.
@J.Young8084 жыл бұрын
I couldn’t get my phone loud enough, but then my phone speaker is crappy. I haven’t had problems on your other videos though. I don’t know what kind of terrain I have here where I live. I am saving for a truck. From looking at IG posts of local Toyota group it doesn’t look too technical where I’d need steel
@RogueOverland4 жыл бұрын
Thanks for the feedback, we will keep the audio in mind on future videos. Sounds like aluminum will be just fine for you.
@sidewaysshed3 жыл бұрын
I run steel. Got them galvanized too so rust isn't a issue.
@RogueOverland3 жыл бұрын
Very nice! Thanks for the input.
@shermfj3 жыл бұрын
Which company's plate and steal vs aluminum, in your experience, would prevent catalitic converter theft?
@RogueOverland3 жыл бұрын
The material shouldn’t matter for that function, it comes down to which one covers the cats.
@mosty298617 күн бұрын
is the arb uvp good for toyota pickup
@FStewBailey4 жыл бұрын
Is it worth getting powder coated steel/aluminum? I’m leaning towards steel after watching this video. 70 pounds is worth the peace of mind.
@RogueOverland3 жыл бұрын
We just use spray paint on ours, as they are going to get scratched anyway.
@tirivaenim Жыл бұрын
In terms of areas where you have your oil or petroleum filter, you could actually do a circular cutout so you don’t have to keep removing the skid plate and also add vents for airflow and heat dissipation, irregardless of aluminium or metal.
@RogueOverland Жыл бұрын
Thanks for the input!
@sha6mm2 жыл бұрын
currently steel going to aluminum live in midwest not a lot of rock but roads are salted in winter
@RogueOverland2 жыл бұрын
Sounds like aluminum will be best for you.
@nscami82334 жыл бұрын
Yeah, something up with the audio. Can't really hear anything unless I use a sound system or headphones.
@RogueOverland4 жыл бұрын
Thank you for the feedback, we are always looking to improve. Thank you for watching!
@lanapatrick3 жыл бұрын
Aluminum works in Florida. Mostly mud! Oh and did I say mud.. lol
@RogueOverland3 жыл бұрын
Lol..... the clean up on mud is no fun. Thanks for watching!
@lanapatrick3 жыл бұрын
@@RogueOverland I know that all to well. I just got back from a trail ride just now and the mud, somehow, just jumped all over my Jeep.
@mandingo9471 Жыл бұрын
Try Mississippi mud
@martywood92992 жыл бұрын
Get rid of the back seats and that will compensate for the weight difference. Then only take a 110lb hottie with you if you go out into the wild. more savings. i Think I will go with steel and maybe go with a combo of steel aluminum. either way, my back seats are out so I will just be adding that wight back and not much more. Thank you for your comparison video sir.
@RogueOverland2 жыл бұрын
Lol…… love it! Thanks for watching.
@shermfj3 жыл бұрын
I went with the RCI steel plate set as more of a theft deterent against catyletic converter theft. I was told it covered and made these very difficult to access for theft. FALSE!!! The cars are fully easily accessible. I was curious. Other than cost, why isn't stainless steel used?
@RogueOverland3 жыл бұрын
That’s a good question. We would guess cost and weight is likely why.
@ryanm40132 жыл бұрын
Cost and weight. It’s very difficult to process
@aspeler223 жыл бұрын
With all the cat steals that are going around and likely to get worse as the drug issue gets worse, I went with steel. Grinding would take longer and be louder to get to them. :)
@RogueOverland3 жыл бұрын
Good point.
@richardc.35132 жыл бұрын
Aluminum sure fills the cutting disc and renders it useless.
@ray83802 жыл бұрын
Would this protect me from theft stealing my gas by drilling a hole on it
@RogueOverland2 жыл бұрын
Probably not as usually a gas tank skid doesn’t cover the sides of the gas tank.
@Jayson11112 жыл бұрын
I'm looking at stainless steel for my Ranger
@RogueOverland2 жыл бұрын
Interesting. Hope that goes well!
@jeromeburrasca67103 жыл бұрын
The bottom line is do not exceed your vehicles GVWR fully loaded with accessories and passengers.
@RogueOverland3 жыл бұрын
Truth! Thanks for the input.
@4wdaddict412 жыл бұрын
Shrockworks !
@RogueOverland2 жыл бұрын
Yes! They make quality stuff.
@ClimbingCrux10 ай бұрын
I have the Bamf full skids. These things are over built and you have to try to damage them!
@RogueOverland10 ай бұрын
They make solid stuff ‼️
@ThePBSD3 жыл бұрын
The amount of weight you are going to save on Immense protection is incomparable in my opinion. STEEL armor is the Only Way To Go. Save your weight on super heavy rack tents, chains, excessive camping gear etc..
@RogueOverland3 жыл бұрын
Carrying excess gear is a really good point! So many people over pack. Thanks for the input.
@SebastianDaniec3 жыл бұрын
@@RogueOverland I come from a hiking background. You learn pretty fast not to overpack when you have to carry the weight your self mile after mile ;)
@RogueOverland3 жыл бұрын
@@SebastianDaniec Truth
@scoobysid043 жыл бұрын
I know it’s like people think that their gear is going to last forever 😂
@venge54is176 ай бұрын
It is not that much of a weight difference at all,I Don't know where do you get specs from..,I checked all weights on rival site and for example the front plate under engine is 17kg steel vs 15alu , transmission 8,3kg vs 8kg , no info for transfer case,for fuel tank is 14kg vs 12kg ...I manage to find different design with the same coverage and strength for tank and is 8,8kg steel... so where do you get that numbers ...I use rival just for example because I'm from europe... and steel and alu are the same design 3mm steel vs 6mm alu... it is not even 8kg for whole set it is nothing...where do you get 60 pounds I don't know..,aluminum looks better when steel plates will get rusted ...I use dinitrol 482 for whole underbody ...even steel plates I covered them on the inside..and on the outside...you can reapply plates with spray in one minute every now en then..drive on the wooden diy ramps ,and lie on the trolley.,spray them and you are good...
@twanboltze81963 жыл бұрын
You need titanium if you want SPARKS
@RogueOverland3 жыл бұрын
😂. Thanks for watching!
@twanboltze81963 жыл бұрын
@@RogueOverland i know a fun idea for a video maybe buy a rc drag version of your truck and modify it to look like yours but add titanium skid plates
@twanboltze81963 жыл бұрын
That would be a fun video idea
@tire26 Жыл бұрын
I don't see how for 95% of people that steel skids aren't better suited. I do like aluminum for roof racks or bumpers as those aren't taking a beating and higher in relation to the center of gravity.
@RogueOverland Жыл бұрын
Good points. Agreed on the roof racks being aluminum as they are so far above the center of gravity. Thanks for the comment.
@robertbalkovec40875 ай бұрын
Aluminium 6061
@RogueOverland5 ай бұрын
👍
@SuperReviews4you3 жыл бұрын
I see skid plates as a consumable item. I would much rather have lighter weight and just buy another set of skids every couple years.
@RogueOverland3 жыл бұрын
Thanks for the input, we love hearing different points of view!
@davidw96312 жыл бұрын
Huh?
@RogueOverland2 жыл бұрын
Not sure what you’re saying but thanks for watching!
@334erty3 жыл бұрын
How much overweight is your Tacoma? My guess is about 1000 lbs.
@RogueOverland3 жыл бұрын
The after market leaf pack is built 1000 lbs over stock. Depending on what’s packed for the trip it’s running around 800-1000lbs payload. Thanks for watching!
@justino89353 жыл бұрын
Watching this video I felt like Stevie Wonder. If Stevie was deaf instead of blind.
@RogueOverland3 жыл бұрын
Ya, our audio was off. Thanks for the feedback.
@souvang71524 жыл бұрын
Aluminum totally a waste should of never even be maded. Sorry coming from a crawler world, find it funny for the price it's stupid for what its it.🤦♂️why?
@RogueOverland4 жыл бұрын
Agreed! No worth it for crawlers. Thanks for watching and commenting.