Step-by-Step DIY 10 min Makita N1900B Electric Power Planer Blade Replacement Setting Adjustment

Рет қаралды 67,926

6 жыл бұрын

Love Of The Grain Workshop shows you the easy step by step instructions for replacing (changing out) your Electric Power Planer blades. Easily done in 10 minutes or less. If you do not have the black blade depth guide you can buy it on Amazon or eBay. If you do not have the supplied nut driver from Makita you can use a 9mm wrench or socket. This is the most thorough guide I’ve seen. Sonce the one from Makita is only given with written instructions and others show you the wrong way to do it without the guide. Which can cause lots of problems. Thanks for watching, commenting, liking and subscribing. Be sure to follow me on Facebook & Instagram as well.

Пікірлер: 88

@johnchapman23 8 ай бұрын

Best video on changing makita planer blades on you tube. Thanks

@loveofthegrainworkshop2891 8 ай бұрын

Awesome! Thanks very much!

@ladykenja2700 5 жыл бұрын

- Very clear, concise info. This planer is new for me. The instructions are so POOR that they could have saved the paper it's written on. Thanx again. You're a life saver.

@loveofthegrainworkshop2891 5 жыл бұрын

lady kenja yes! Thats why I made the video. There were some vids showing part of it and not giving correct instructions either. So I read everything and combined all the info.

@eselick 3 жыл бұрын

Thanks for this great video. I took the blade assembly apart and was lost until I found your video.

@loveofthegrainworkshop2891 3 жыл бұрын

Yep! I was there as well before this. I saw instructions from the company which were incomplete. And a video that was incomplete. So I knew it would help someone.

@m.d.1473 5 жыл бұрын

I have the same model planer that I picked up secondhand. I was wondering what the black block was for. I had no idea it was to assist in installing the blades. Thanks for the video. Six doors later, I can say, it's a great planer. Now if I can only figure out how to remove cotton material from the side of the spin wheel. I caught my t-shirt with the tool and jammed it up. Moral of the story, quit before you get tired and a little careless.

@loveofthegrainworkshop2891 5 жыл бұрын

M. Drier haha! I should do a video for that as well. I caught a cotton blanket it was resting on once as well as its own power cord once. I didn’t notice it was under the planer when I ran it over the surface. You have to disassemble the whole thing. Both bottom plates. The black cover on the side , the belt, the nuts holding the bearing wheels in place. Then a hammer and screwdriver to bang out the bearings. Fun fun fun. Glad this vid helped.

@1029pb 6 жыл бұрын

Wow thanks for the in-depth review and learn something even though I’ve been using this planer for years

@loveofthegrainworkshop2891 6 жыл бұрын

Absolutely! Glad it was helpful!

@charlesgerlach7059 5 жыл бұрын

ty that was awesome, I just moved to NC and there was a big tool shop on the property, it is a mess but a ton of power tools, i found this Makita still in the box . used your video to change the blades .. I also found 2 Rockwell Versa Planers Model 633 . that work but l know nothing about.. along with a dozens of drills . sanders, saws routers . anthing from Bosch to Makita to Dewalt along with 2 drill presses, 2 table saws, joiners and other stuff. just an amatuer hobbist and going to be selling some of these dont need it all . Thanks for the Video it works great

@loveofthegrainworkshop2891 5 жыл бұрын

Charles Gerlach what?! Wow! Where in NC. I’m near Wilmington on the coast. Which ones are you selling off?

@charlesgerlach7059 5 жыл бұрын

@@loveofthegrainworkshop2891 pretty much most of it i dont need it, i just found . 2 . Rockwell Planers . model 733 . plugged them in they work great, we are in Pikeville outside of Goldsboro . have router tables, dovetail things . drill presses, band saw . jig saws . ect .

@charlesgerlach7059 5 жыл бұрын

@@loveofthegrainworkshop2891 good morning . just sending another reply, pretty much everythign is for sale, just cleaned up the Delta contractor saw, bed was rusted, l need that, Have a Delta Jointer from 1940 cleaned that up and have been using it.. but that is up for sale.. it works good. and lots of other items...let me know if you are interested

@kennkid9912 4 жыл бұрын

My Delta Contractor saw was bought new in the eighties.It still In use.A great saw.Cost like $450. On sale. It's A good one.Lucky you.

@meghancass3187 9 ай бұрын

Great video. I've had a couple of these planers over my life. Recently bought a Festool planer because the homeowner wanted a special exposed handhewn rafter detail throughout a home (they offer a shaped cutter head good for that) and I figured I'd end up using the Festool exclusively after that. Not so much. I like my Makita for normal planing tasks much better. Great little tool.Now how bout a tuning video? You can really dial these planers in nicely.

@jod6045 6 ай бұрын

Thank you very much!

@loveofthegrainworkshop2891 6 ай бұрын

You're welcome!

@robertbascelli6433 2 жыл бұрын

I had recently acquired one from a friend thats finished woodworking. This video was an amazing find. You must be very careful reinserting the new blades. If it's off just a hair, it will bind inside so give it a couple of hand turns first to make sure the blades don't touch anything inside before turning it on

@loveofthegrainworkshop2891 2 жыл бұрын

Absolutely! Great suggestion

@paulyanney3151 2 жыл бұрын

Thank you I about to change the blades in mine and your video is a huge help!!

@loveofthegrainworkshop2891 2 жыл бұрын

Thanks

@NirreFirre 11 ай бұрын

For those looking for OEM spares, the 793322-2 seems to have been replaced by D-07945 (82 x 5,5 x 1,2mm)

@christophergunn8749 4 жыл бұрын

Very clear and concise, got the exact information i required, thanks

@loveofthegrainworkshop2891 2 жыл бұрын

Thanks!

@scottwood5098 7 ай бұрын

Looks like the original huge blades are compatible instead of those crappy tiny blades. Awesome.those tiny blades are 30dollars Canadian and $10 for the kick ass huge original blades from 40. Years ago

@loveofthegrainworkshop2891 7 ай бұрын

Cool

@philsutt 5 жыл бұрын

Clear and concise thanks 👍🏻

@loveofthegrainworkshop2891 5 жыл бұрын

Phil Sutton your welcome.

@FlyingVneckSweater Жыл бұрын

Winner! 👍🏼

@loveofthegrainworkshop2891 Жыл бұрын

Thanks

@backyardarts3322 8 ай бұрын

Thank you, this vid was really helpfull

@loveofthegrainworkshop2891 8 ай бұрын

Absolutely!

@adelismail6403 5 жыл бұрын

thank you sir great job

@loveofthegrainworkshop2891 5 жыл бұрын

adel ismail glad to be of help

@texaswoodhouse6158 Жыл бұрын

Great video... Oil that bearing

@loveofthegrainworkshop2891 Жыл бұрын

Yes indeed.

@kennkid9912 4 жыл бұрын

My old 1900b uses a wider tool steel blade.Never used it much it was bought many years ago used. Will pick up a carbide blade. The old blade is duller than I am. No paperwork of coyrse.Thanks.

@loveofthegrainworkshop2891 2 жыл бұрын

No problem!

@despotcustodio 5 жыл бұрын

thank you

@loveofthegrainworkshop2891 5 жыл бұрын

despot custodio sure no problem glad I could help.

@sciencemansandera 11 ай бұрын

BTW, nice video thanks The two most popular planners are this one in the Bosch and the 2632 Bosch has a twin blade. They are much faster and easier to change and seem to leave a very nice finish but might not cut is duct where this planer apparently will cut an 1/8 inch deep. Any thoughts on that? Have you had to cut very much stuff that deep I am going to be cleaning rough sawn lumber from an Amish mill. I also have a big planer machine but I don’t have it online right now I’m considering buying one of each.😮 going to be building a small Timber Frame Home

@loveofthegrainworkshop2891 11 ай бұрын

I only have this brand. Have not tried the Bosch. This will cut very deep though it’s hard on it. So you need to cut shallower anyway.

@jon_byler 2 жыл бұрын

great video, thanks! I wish they would tell how many inch/foot pound to tighten those blade retention bolts!

@loveofthegrainworkshop2891 2 жыл бұрын

Me too. But not sure. I crank them pretty tight though.

@roscored1000 3 жыл бұрын

had a look at my old machine and they are not square with the base, will finding a gauge help to reset those? thanks for the video

@loveofthegrainworkshop2891 2 жыл бұрын

Absolutely!

@catherinehargreaves9959 5 жыл бұрын

exelent, i agree with all the good coments. lignator jack . uk.

@loveofthegrainworkshop2891 2 жыл бұрын

Thanks

@robertd6925 3 жыл бұрын

Have you used the carbide blades? If so are they worth the extra money?

@loveofthegrainworkshop2891 3 жыл бұрын

Yes I have. I think they absolutely are.

@kylekells7937 5 жыл бұрын

Can't seem to find the blade depth guide anywhere, maybe I'm searching incorrectly? Any advice? Thanks!

@loveofthegrainworkshop2891 5 жыл бұрын

Kyle Kells “Makita 123010-1 Blade gauge” search the above phrase on Amazon.

@PhuongTruong-ml2rh 4 жыл бұрын

Hi Bro,can i ask the blade set gauge compatible to all planer ?

@loveofthegrainworkshop2891 4 жыл бұрын

Phuong Truong I don’t know. If it’s similar in build to this one it should

@mdmd-mf3bg 5 жыл бұрын

It be nice to have the measurement for that guage block! :) would like to make one... thanks

@user-sj4ls8jc4i 3 жыл бұрын

Hi, good question, did you get it? I am looking for the same item! Thanx in advance

@mdmd-mf3bg 3 жыл бұрын

@@user-sj4ls8jc4i no i ended up just using a square and a block to get it close and flat.... it was good enough for me... although id still like that measurement so i can get it perfect :)

@user-sj4ls8jc4i 3 жыл бұрын

@@mdmd-mf3bg Yeah, I can agree on that but it seems this is one of those secrets... the manufacturer wants to hold on to their ideas... if I find something I will share it.

@user-sj4ls8jc4i 3 жыл бұрын

Hey, i measured it and from the edge it is 3.3 cm. Don't know what u use but this way you can make it probably. Good luck!

@mdmd-mf3bg 3 жыл бұрын

@@user-sj4ls8jc4i thanks!

@mikedehaan81 3 жыл бұрын

I think I have an issue with the blade depth relative to the back plate. My question is, if I set the planer on a flat surface and turn it on, should the blades make contact with the wood? In other words, if everything is set to zero, would the planer still cut an already perfectly flat piece of wood? ....should it? Thanks.

@loveofthegrainworkshop2891 3 жыл бұрын

I dont think so no! With the front plate adjusted to the same plane as the back plate. The blade should bot touch wood.

@timothyball3144 5 жыл бұрын

Just got this planer and was wondering what those other parts were for. Now I just need to find a video on using the sharpener.

@loveofthegrainworkshop2891 5 жыл бұрын

Timothy Ball the blades are really cheap. Just buy new ones.

@timothyball3144 5 жыл бұрын

@@loveofthegrainworkshop2891 I took a closer look and saw that I don't have the little, slide in blades, but rather, the big, solid blades. I used the jig to put an edge on them just to see what it's like. If these get full quickly, I'll get the adapter and install the small blades.

@TerryWysocki 4 жыл бұрын

Same as Timothy Ball. I have the 1900B model and it has the cutting edge right on the 1"x3" steel piece! I assume that the little black rectangle I got with the unit is the guide for new blades of this sort too??? Then I'm also puzzled about what the other black plastic beveled piece on a metal plate with thumbscrews is for??? BTW, I saw a another vid that has a really good discussion on planers which helped me understand how they're supposed to work: kzfaq.info/get/bejne/lcdhe6aisJvNXXU.html

@bikerboy2791 3 жыл бұрын

@@timothyball3144 I don't understand the difference between the smaller blades and the larger ones. Makita lists part # D-46230 as replacement blades for the N1900B planer, but these are larger than the small blades shown in the video.

@gilbertecal5969 4 жыл бұрын

I want to know how to remove & replace bearing on blade drum.. Tnx.

@loveofthegrainworkshop2891 4 жыл бұрын

Gilbert Ecal i’ll have to make a video on that.

@MOUTHonesixtyseven 6 ай бұрын

Why did you loosen the adjustment screws ? Couldn’t you have just left them alone and replaced the blade?

@loveofthegrainworkshop2891 6 ай бұрын

As blades wear down. You adjust them. So with new ones you should adjust them to the fresh blades.

@MOUTHonesixtyseven 6 ай бұрын

so if I haven't adjusted my blades before, but knicked them on a nail and want to replace them, I technically do not need to do any adjusting --I can just replace them with out the set block. (I lost mine)@@loveofthegrainworkshop2891

@loveofthegrainworkshop2891 6 ай бұрын

@@MOUTHonesixtyseven yep correct

@californiacreativecenter9486 5 жыл бұрын

Where to get the "guide?" How to best adjust the depth of cut? Why the 4 screws in the bottom plate?

@loveofthegrainworkshop2891 5 жыл бұрын

William Bergmann if you don’t have the guide you can get a replacement on eBay or amazon. Adjusting the depth is the black knob on the top front. The four screws on the bottom plate just hold the plate on. They do not adjust anything.

@loveofthegrainworkshop2891 5 жыл бұрын

William Bergmann “Makita 123010-1 Blade gauge” search that phrase on amazon.

@californiacreativecenter9486 5 жыл бұрын

@@loveofthegrainworkshop2891 Thanks