STM32 Nucleo - LED BLINKING USING NUCLEO DEVELOPMENT BOARD AND KEIL uVISION IDE

Рет қаралды 34,065

4 жыл бұрын

In this video, I have covered basic features of Nucleo Development Board
1) Basic understanding of Board.
2) Peripherals on board.
3) CubeMX + KEIL code understanding.
-----------------------------------------------------------------------------------------------------------
You can support my channel at-- Paytm: +91-8655761125
Paypal : paypal.me/electrofunedu
-----------------------------------------------------------------------------------------------------------
For more details you can visit my website here:
-----------------------------------------------------------------------------------------------------------
Some of my other videos are:
Getting started with stm32 - Bull Pill Board (STM32F103C8T6)
• Getting started with s...
Raspberry Pi PDF Reader
• Raspberry Pi PDF Reader
Getting started with Raspberry Pi - Setup & Boot without external LAN or MONITOR
• Getting started with R...
Raspberry Pi 3 - Introduction and First Impression
• Raspberry Pi 3 - Intro...
Arduino Introduction - Hardware, IDE setup and Led Interfacing
• Arduino Introduction -...
Keil Tutorial for 8051 Micro-Controller using hardware Complete Explaination.
• Keil Tutorial for 8051...
8051 Programming in keil + hardware tutorial 2
• 8051 Programming in ke...
Bluetooth Control pick and place Robot with 3 DOF
• Bluetooth Control pick...

Пікірлер: 19

@refused_hc7882 4 жыл бұрын

Much thanks! very useful! Tested with last Cube and Nucleo STM32F446 and working perfectly this demo!

@electrofun5135 4 жыл бұрын

Your welcome..... Please Like, Share and subscribe our channel... Stay tuned for more such upcoming videos

@yosterdaniel1213 3 жыл бұрын

doesnt work using my board f446, it doesn't wait for button input. It just runs the code and blinks the LED without input

@electrofun5135 3 жыл бұрын

If you are facing that issue, just connect am external button on any other pin and check. Hope this can help you solve issue. Also check the circuit diagram of how your button works. Thanks

@sam-pd6zi 2 жыл бұрын

thanks , i bought a nucleo and didn't know how to use it for, thanks for your video.

@electrofun5135 2 жыл бұрын

Woww glad my video helped you. All the best with your development with nucleo board Stay tuned for more such upcoming videos

@fjdarling 10 ай бұрын

I apologies for my rudeness. My hearing is not as sharp as it used to be. I'm a frustrated, old retired Engineer trying to keep up with new technology. Still, you responded like a perfect gentleman. Thank you for your response. I'll continue to check your education site.

@electrofun5135 10 ай бұрын

No worries. I appreciate your candid feedback. I will make sure to incorporate that in my next set of videos. Happy learning sir !! Thank you

@yacho0 3 жыл бұрын

Thanks Man!

@electrofun5135 3 жыл бұрын

Welcome buddy.

@user-qk4my7pd2s 8 ай бұрын

Cooooool

@electrofun5135 8 ай бұрын

Thanks

@gabrielcabrerasanchez1542 2 жыл бұрын

Thanks for the video bro, I have a question for you, i have a nucleo-f429zi, when i did al the steps in the video my nucleo board don't do anything, but when I program it in Keil Studio on line, yes it's functional, Do you know why i have that problem?

@electrofun5135 2 жыл бұрын

Hey man, you might be missing something or try using the older version of the code generator and check. Thanks

@skilful_official 3 жыл бұрын

How can I do that at ST Visual Develop?

@samarthshetty2268 2 жыл бұрын

Is this necessary to use Hal libraries? Is it posible to blinkWithout using HAL library and cubemx.

@electrofun5135 2 жыл бұрын

Yes, it is possible to build without HAL libraries and cubemx. You will have to do a lot ground work which includes initialization (power, pins, clock, crystal, etc). Once that is done you can then assign the pin and create a blinky. Hope this answers your question. Thanks

@fjdarling 10 ай бұрын

I'm sorry. You are too heavily accented and you have no subtitles. I can't benefit from your what you have to say.Still, I gave you a thumbs up.

@electrofun5135 10 ай бұрын

I am sorry about that. Yeah my accent has been a little different compared to others. Although it's also quite an old video with an old setup. Newer videos should be well understandable and clear in terms of accent. Thank you.