STM32CubeMX basics: 13.2 STM32Cube HAL labs ADC

STM32CubeMX basics: 13.2 STM32Cube HAL labs ADC - Lab ADC DMA

Рет қаралды 21,431

Күн бұрын

This lecture is part of the MOOC - STM32CubeMX and STM32Cube HAL basics • MOOC - STM32CubeMX and...
Please see below hands-on mandatory pre-requisites and additional links.
Hands-on technical pre-requisites:
- PC with admin rights running Windows 7 or higher
- STM32 nucleo kit NUCLEO-F401RE www.st.com/en/evaluation-tool...
- Mini USB cable
- Java JRE www.oracle.com/technetwork/jav...
- STM32CubeMX www.st.com/en/development-too...
- STM32CubeF4 firmware www.st.com/en/embedded-softwa...
- ST-LINK USB driver www.st.com/en/development-too...
- A development IDE, either IAR, Keil, Atollic or SW4STM32
MOOC slideset: drive.google.com/open?id=1H2O...
MOOC lab archive: drive.google.com/open?id=1R59...
MOOC lab documentation: drive.google.com/open?id=18v5...
Additional references:
- UM1724 NUCLEO-F401RE user manual www.st.com/resource/en/user_m...
- UM1718 STM32CubeMX user manual www.st.com/resource/en/user_m...
- Additional information on How to use SWO to print information from STM32 drive.google.com/open?id=1Xv0...
Tell us what do you think about this MOOC through anonymous survey: www.surveymonkey.com/r/TTB3TYM

Пікірлер: 11

@ibrahimboudjenah598 4 жыл бұрын

what can i change when i use more than one channel in circulaire mode with dma

@bennguyen1313 3 жыл бұрын

When enabling the ADC's SCAN option, will there will be a delta time between when the first channel of the sequence was sampled, and the last channel? For example, If you have the ADC enabled to scan 8 channels, then if you use a 16Khz Timer Trigger Out Event as the External Conversion source, then ch1 would always be sampled in sync with the 16khz trigger event, but channel 8 is always sampled at 16khz+delta? And if you do want the timer output to be the trigger source, what should the ADC's "Continuous Conversion Mode" option be set to? Using STM-STUDIO-STM32, I can't tell what changes when ContinuousConvMode = ENABLE vs DISABLE;

@stmicroelectronics 3 жыл бұрын

Hello! Visit our online community to find answers to your technical questions and share ideas with our developers and ST experts : community.st.com

@fifa7150 4 жыл бұрын

Is it possible to measure different channels from one ADC using: HAL_ADC_PollForConversion(&hadc1,___) ? I mean without using DMA or IT. I have used the next code, but It didn't take the values frome the two channels I defined. The code I am talking about is the next: while (i

@Graham1904 4 жыл бұрын

I must have missed something, what made the adc value go 4096 to zero and back?

@stmicroelectronics 4 жыл бұрын

You are right, it was not obvious from the video. There is a button with pull-up on PA0 (like on NUCLEO-F401RC board).

@subashinikrishnan4890 3 жыл бұрын

@@stmicroelectronics a

@hasenlamano 4 жыл бұрын

A lot of configs shown in many videos of this series are not easly found in the new cubeMx 5.xx

@stmicroelectronics 4 жыл бұрын

Hello. What I would recommend you for a while is our another session, MOOC - STM32G0 workshop which is focusing more on STM32CubeMX. In the meantime we are working on an update of STM32CubeMX session.

@itonjoans354 4 жыл бұрын

Why did you change optimization? there is no explanation why, also why did you change from STM32cube ide to IAR, these series of videos are very hard to follow.

@DangNguyen-oj9df 4 жыл бұрын

It is in an other video, please check again. Compiler may remove some unnecessary code for optimization so that program can not stop at break point.