String trimmer pull cord repair

No video

String trimmer pull cord repair

Рет қаралды 39,284

Күн бұрын

This is a more detailed video of the pull cord assembly and fixing a pull cord that won’t wind back.
T15 torx single tool: amzn.to/3OZsIAV
Torx tool set: amzn.to/3qp9NpN
I wasn’t able to find much info online on repairing/replacing the pull cord on these newer front side mounted weedwhackers. The pull cord is mounted between the motor and the pole. So I decided to post a video that may help make it a little easier for someone. Sorry for the poor video quality.
This video is intended for informational and educational purposes only. I want to stress the importance of safety when working with tools. Always exercise caution and follow proper safety guidelines when handling tools or attempting any repairs. The methods and techniques demonstrated in this video are performed by a trained individual with experience. However, it is crucial to note that there is always some level of risk involved when working with tools and machinery.
If you're unsure about any aspect of a repair or don't have the necessary experience, it's strongly recommended that you seek professional advice or assistance. Attempting repairs without proper knowledge can be dangerous and may result in injury or damage to tools and equipment.
By watching and following the instructions in this video, you do so at your own risk. The creator of this video and any associated parties cannot be held responsible for any injuries, accidents, or damages that may occur as a result of your actions. Prioritize your safety and that of others around you when working with tools."
This disclosure makes it clear to your viewers that they should prioritize safety and exercise caution when attempting any repairs and that they assume any risk involved in doing so.
This is a wc210 25cc craftsman string trimmer. But as far as I can tell, there are many makes and models with the same set up. Bolens bl110; bl160, Troy bilt tb25; tb22;, yard machines y765; y25t, craftsman WC205, WC210, WC215, WC2200, WS205, WS210, WS215, WS2200, ws205; ht2200; ws4200; ws2200, BT720 TB10CS TB15CS TB20CS TB20DC TB21EC TB22EC TB26TB TB26CO TB32EC TB415CS TB475SS TB50 YardMan YM1500 YM300 YM400 791-153066B TB525ec
Homelite ST155 ST165 ST175 ST285 Murray M2510
Ryobi CS30 SS30 RY30040A RY30040B, Homelite ST155 ST165 ST175 ST275 ST285, Replaces UP04650A 000998265 DA03174A DA04591A
316791020 316711370 316711470 316711471 316791080 316791081 316990110 31679111 31679112 316791190 316791191 316794400 316990100 316792520 316794370 316794470 316794470

Пікірлер: 117

@murse_bagger Күн бұрын

After the many videos I searched trying to figure this out, your video was the most helpful. Thank you very much for that!

@SHONEY21Z Күн бұрын

Glad it helped. And thanks for sharing!

@wooleyboogger Ай бұрын

Great detail video! Rope in the spark plug port was the BEST trick ever! Could not have done it without that tip. THANK YOU

@SHONEY21Z Ай бұрын

And thank you sir for commenting. Glad I could help. Every like and comment helps the channel!

@jacksonianc 4 ай бұрын

Holy smokes-I never would have attempted this repair but I just got through it and it went great. Really great tutorial, saved me some $$$

@SHONEY21Z 4 ай бұрын

These are the comments I look forward to. Thanks for the feedback. Glad I could help!

@gerry_904 Жыл бұрын

Much more detailed....Thanks so much for responding to the concerns of your viewers.

@SHONEY21Z Жыл бұрын

Thanks for the comment. Cheers

@charlescooper1577 Жыл бұрын

Seen the cord in spark hole mentioned in comments on another video, wasn't sure about it. after seeing you do it I tried it and worked perfectly. Good job, thank you

@SHONEY21Z Жыл бұрын

Glad I could help

@tomford1805 2 ай бұрын

Thank you for this detailed video. I just needed to know how to get the cord to retract after replacing a broken one. 👍

@SHONEY21Z 2 ай бұрын

No problem. Glad I could help.

@OhanaTowels Жыл бұрын

Fantastic - Thank you very much. I came across to this from another (abbreviated) video, for which I agreed with others (and you) that there were steps missing. I watched this one step-by-step while doing my own pullcord repair and it reflected it perfectly. (Note - I had trouble removing the split washer (and replacing it again - perhaps I should have bought a new one). Anyway, this video got my through the process A to Z. Thank you.

@SHONEY21Z Жыл бұрын

Thanks for watching. And glad I could help!

@PavelPlucha Ай бұрын

O@@SHONEY21Z

@joew9392 Жыл бұрын

I'll probably be doing one of these shortly, the video was a great help! Thanks!

@SHONEY21Z Жыл бұрын

Glad I could help. Good luck!

@johnnytamez4432 7 ай бұрын

Hello I'm jon that video about replacing string to start weed eater was very good to watch and learn you make it look easy and it was thanks to you Thank you

@SHONEY21Z 7 ай бұрын

Glad I could help. Thanks for watching

@PavelPlucha Ай бұрын

7:38 oko pod se

@PavelPlucha Ай бұрын

@@SHONEY21Zod začátku o

@PavelPlucha Ай бұрын

@@SHONEY21Zok LP popis

@PavelPlucha Ай бұрын

O oo OOPP PP😊pplk.. P IP oiui.pppo

@larryharrelson2540 3 ай бұрын

Hey bro, GOOD JOB. You gotta be payin the preacher EVERY Sunday morning or something, because that aint natural for that spring to go back together that easy.How many times have I had one come from undone andtwist up lookin like a tennis ball.LOFL.

@SHONEY21Z 3 ай бұрын

There is a tool for it but I don’t have it haha. I’m not gonna lie, my hands were cramping by the time I got all the spring tight enough to get it inside the plastic spool.

@colefisher4010 2 ай бұрын

OMG what a helpful video! Thanks so much man!

@SHONEY21Z 2 ай бұрын

Appreciate the support

@UPWAY2HIGH Ай бұрын

Outstanding instructions. Really appreciate the help. The lock washer on my machine is split so I will need to get a replacement. I can't find the part online. Would you happen to know the part number for that retainer?

@SHONEY21Z Ай бұрын

This question was asked before and I was unable to find that part sold individually. I can’t guarantee a fit but I suggested trying something like buying a kit like this amzn.to/4fj4Q6e with various sizes. Or check local hardware store/tractor supply.

@UPWAY2HIGH 25 күн бұрын

@@SHONEY21Z Thanks for the advice. That was the route I was hoping to avoid as I hate to have so much excess stuff that's hard for me to throw out. I will measure the outside diameter and get a kit that includes a push on retainer ring that will fit. Thanks again!

@MrRaulgutierrez95 Жыл бұрын

Ill support all your videos by liking alll that apply to me

@SHONEY21Z Жыл бұрын

Thanks for the support!

@al52269 2 ай бұрын

Great video. Thanks for sharing. New subscriber here

@SHONEY21Z 2 ай бұрын

Thanks for the sub!

@zanenelson8564 Ай бұрын

No matter what I try.....I can't get the torx screw off that holds the clutch drum on. This one I'm working on is a Craftsman.....but as you know it's the same. My screw is a T30 and it looks as if someone may have messed it up. Any suggestions. I sure hate to drill it.

@SHONEY21Z Ай бұрын

That’s a tough one. Stripping that screw is a major ordeal. I would search Amazon/harbor freight or anywhere you can think of for a long skinny stripped bolt extractor. Another option I’ve seen ppl try is hammer a flathead into the bolt head to try and make new groove and turn it that way. I’ve also seen this done with a slightly larger torx T-handle

@copiamarie6238 2 ай бұрын

Early in the video, you mention the need for a long handled T15 and T20. Later, you state that you are using a T25 to remove the shaft that covers the clutch. Did I misunderstand or did you possibly mix up he T15 for the T25? I need to buy the part. Thanks for a great video.

@SHONEY21Z 2 ай бұрын

It’s a T15 torx long handle to get the clutch bell off. There’s a link in the description the tool at Amazon.

@copiamarie6238 Ай бұрын

@@SHONEY21Z Thank you! I appreciate the video and the prompt reply to my query. I bought a set of long-handled torx wrenches at amazon and it includes the necessary size. My weed whacker is not the same model as yours, but it is very similar and your video helped me muddle through the project. I pulled the thing apart, put new line on, wound it up, etc. etc. It retracts nicely in its plastic housing until I reattach it to the weed whacker and pull the cord against the resistance of trying to turn the piston. Now when I pull the cord, it is not engaging the engine. It just makes a ratchet-sounding noise like it is slipping; clearly it won't start the engine this way. Any ideas? Might the part that catches the engine be worn out? I can't see that it is, but I don't have a lot of experience at this. Thanks.

@SHONEY21Z Ай бұрын

It sounds like the paws aren’t engaging. Sometimes they get stuck and need lubrication and sometimes it’s assembled wrong and somethings hanging up

@Brad-z2e 2 ай бұрын

Does anyone have a source for the "lock nut" that holds down the starter recoil as shown at 8:20? I split it removing it.

@SHONEY21Z 2 ай бұрын

The part isn’t sold individually. You’d need to buy the whole starter assembly for around $25. You could try to match it from a kit of end cap clips like this one from Amazon. amzn.to/3KSrGDZ

@courtneyaxtman8645 3 ай бұрын

What ‘groove’ are you talking about at 16:49 awesome video but once it gets to rewinding the pull cord the directions are hard to follow

@SHONEY21Z 3 ай бұрын

Is everything together but the cord all the way out? If so then you are ready to start winding up the spring. Pull the cord out from the inside of the cover. There’s a groove in the white pulley, lock the cord in that groove and start winding the pulley clockwise about 5-6 times. Then let go of the pulley and it should retract the cord

@mrpbjnance Жыл бұрын

Sorry one more question and I think I messed up and have to restart. When you are winding the spool.. the string is NOT winding up right?

@SHONEY21Z Жыл бұрын

Is the spring there and not broken?

@MrRaulgutierrez95 Жыл бұрын

What spring? Looks exactly like the video

@MrRaulgutierrez95 Жыл бұрын

Doesn't my bad

@MrRaulgutierrez95 Жыл бұрын

Yeah for real same question too is it winding?

@drizler Жыл бұрын

I hope there is a special place in hell reserved for whoever created that damned spring .🤬 I just spent 2 hours repeatedly winding that cursed thing and it’s still off. My hands feel destroyed!

@larryharrelson2540 3 ай бұрын

A question for you or anybody else out there that's in the know. On the one i'm working on there's a little sliding piece of black plastic that slides in the housing up against the coil/ spark plug wire, I put a new coil on and it had spark just fine until I reassembled .on the old coil there's a ,Emory mark where the slider was rubbing on it. Have you or anybody else had issues nwith the lil slider?

@SHONEY21Z 3 ай бұрын

Are you sure that’s the problem? Could be a grounding issue. Check all the wires and attachments over again.

@rustysanders1062 Жыл бұрын

Aye so the notch that the string is supposed to lock into. How does that work? It would leave the string hanging off the side a little and cause it to get caught, would it not? Im confused.

@SHONEY21Z Жыл бұрын

At 16:45, you can see this being done, sort of. With the string fully extended and no tension on the spring, pull the string inward toward the pulley and make a loop. Hook the string into the notch and start turning the pulley clockwise. About 5/6 turns at most. (Depending on the length of your string) then pull the pull cord handle out so there’s no more loop and the n allow the pulley to retract the pull cord.

@philliphall5198 Жыл бұрын

Hoping you made a profit 😊

@SHONEY21Z Жыл бұрын

Thanks my man!

@mrpbjnance Жыл бұрын

Is there any other way to block the piston other than shoving a rope down?

@SHONEY21Z Жыл бұрын

Zhiqinge Universal Nylon Piston Stop Tool 2 Stroke 4 Stroke Engines 10mm & 14mm a.co/d/ehCJ6c8 These have mixed reviews

@MrRaulgutierrez95 Жыл бұрын

The sting method worked perfrect. Never thought of that. So simple yet effective.

@SHONEY21Z 9 ай бұрын

Great news!

@downeykids 2 ай бұрын

What kind of rope is that? Where would I buy it?

@BeatMoneyAD 10 ай бұрын

When I use the t15 to remove the screw, it doesn’t loosen. It keeps spinning the pull string inside. What am I doing wrong? I have the craftsman WC2200

@SHONEY21Z 10 ай бұрын

Did you block off the piston? Otherwise you’ll be turning the motor over when you try unscrewing the torx bolt.

@BeatMoneyAD 10 ай бұрын

@@SHONEY21Z yes I got it now

@wesbrown5708 3 ай бұрын

On the T15 do you turn counter clockwise or clockwise ?

@SHONEY21Z 3 ай бұрын

Lefty loosey (counter clockwise) but make sure to block the piston from turning as well when taking the clutch off.

@wesbrown5708 3 ай бұрын

Thanks, I blocked the piston but the t15 will not budge. Any idea what might be the issue?

@SHONEY21Z 3 ай бұрын

@@wesbrown5708there’s an arrow showing the direction to spin the clutch I used a wrench on the square part of the clutch and started turning in the direction of the arrow while holding the trimmer head tightly

@wesbrown5708 3 ай бұрын

@@SHONEY21Z I meant the t15. I blocked the piston but still cannot get it to budge. Any idea what might be the issue?

@SHONEY21Z 3 ай бұрын

Hmm. It’s probably just very tight. It’s scary to turn but as long as the t15 is seated well and a lot of downforce it shouldn’t strip. It takes a lot of force to crack the bolt but then it comes out easy. A long t15 bit on an impact would probably break it open easier but if it slips it strips. That’s my best suggestion just to use the handle and turn pretty hard with down pressure. Hard to hold the head and the tool at the same time but it should loosen.

@titodiaz9044 6 ай бұрын

Hello I have a question how much cord should I put ?

@SHONEY21Z 6 ай бұрын

Should be about 4 feet. Go a little long, can always cut off excess.

@martindriggers4150 Жыл бұрын

Seems to be a Craftsman design flaw for sure!

@SHONEY21Z Жыл бұрын

Terrible engineering

@Joe4it-wy1th 10 ай бұрын

Poor engineering, yes. Not craftsman, MTD.

@brandanevans5626 Жыл бұрын

I have a craftsman 2 cycle 25cc and im on the clutch part of it and every time i turned it the clutch wont come off idk if im doing something wrong or what

@SHONEY21Z Жыл бұрын

Is the motor turning over? Or is it turning a little with spring tension? You have to take out the spring tension and then turn it a little further to break it free. It’s not easy.

@funnypants1234 Жыл бұрын

Yeah, my clutch will not come off !the Pistons is not spinning, It is just super tight.

@funnypants1234 Жыл бұрын

I don’t know why your clutch came off so much easier

@SHONEY21Z Жыл бұрын

@@funnypants1234 does it feel spring loaded when you turn it? Because you have to push through the secondary spring until it’s uncoiled and the lm turn it a little further to break the clutch free. Try using a little penetrating oil near the threads or slightly heating it but don’t melt the plastic.

@MrRaulgutierrez95 Жыл бұрын

Mine is wc2200 maybe thats why i am having trouble.

@SHONEY21Z Жыл бұрын

Did you get it figured out? It’s possible you have a broken spring

@MrRaulgutierrez95 Жыл бұрын

@@SHONEY21Z not yet. I don't think so because my cord. Just ripped. And just neede that. Soon as I start put rope. It started right up but I didn't wind it correctly. I have 2 identical 4 stroke ones side by side The issue is with the 2cycle one. It's just slightly different. Doesn't have that plate. Like yours. And everything else but no plate. But you know what I it could be. I just think the part where you put the cord on the groove. I cant seem to do it like you did. Ive watched the video over and over. Maybe in just stupid or maybe it is broken. How do I confirm that. Minr doesn't have visiblly that spring you like your s. But when i put it together the rope rope will retract. But then got stuck after s few times. So I know it has tension. How can I show you. ~? Maybe post. A video on my channel and send link. Appreciate you responding. Been doing it for 2 days just got over it.

@MrRaulgutierrez95 Жыл бұрын

@@SHONEY21Z video does it so easy and must be doing something wrong. I don't think spring is broken. But I have been wrong before

@SHONEY21Z Жыл бұрын

@@MrRaulgutierrez95does yours have the small color that holds the pull cord assembly down? I call it a lock washer.

@MrRaulgutierrez95 Жыл бұрын

@@SHONEY21Z yes i didnt Remove it.? Left as is.

@N1RuffinFan Жыл бұрын

Good details until it was time to wind the cord back in. Almost like you purposely didn't want to show how it was done.

@SHONEY21Z Жыл бұрын

@ 16:45 you can see how I pull the string through and hook it onto the little notch on the white pulley. I turned to 5 times but needed 7 times. So there really wasn’t much to see on the second 2 extra turns. Sorry about the camera view. Not always easy to make sure I’m in perfect view while making the video.

@dennyhall4466 Жыл бұрын

That’s the step I am on and it’s just not happening for me lol. I be turned it back times but great video any advice?

@dennyhall4466 Жыл бұрын

Can you make one zooming in on cord and weel when your turning it 5 to 7 times lol 😂

@SHONEY21Z Жыл бұрын

@@dennyhall4466 unfortunately Idont have one in the shop right now. What are you having trouble with? Is the spring in and the pulley in place? And now the string is all the way out but not coming back in? If so I’ll can try to talk walk you through the next step

@kksnodgrass Ай бұрын

@@SHONEY21ZI watched this video and fixed my weed wacker once, now like a lot of people I'm having trouble getting the cord to retract (after pullcord pulled all the way out again; repair attempt #2). The spring is in and recoiling. When I put the string into the notch to start winding the pulley, it doesn't feed onto the pulley reel without contacting the sides of the housing. If I just let the pulley go after winding, it bunches up without retracting the pull cord. Any advice?

@downeykids 2 ай бұрын

Don"t buy thicker cord. Mine does not fit. Buy the same cord width

@SHONEY21Z 2 ай бұрын

Good point. 3 or 4mm pull cord is recommended

@roscodrummer 3 ай бұрын

Dude noby can see where on the spool what your doing it's out of picture

@SHONEY21Z 3 ай бұрын

I know. Didn’t know it until I went back to do the editing. Basically placed the rolled up spring into the white plastic pulley

@Ty4ever Жыл бұрын

MTD JUNK!

@SHONEY21Z Жыл бұрын

Yep

@MrRaulgutierrez95 Жыл бұрын

Im having so much trouble. I dont get the string part. 16:04

@sheripena8262 Жыл бұрын

Yes

@SHONEY21Z Жыл бұрын

Did you ever get it wound?

@MrRaulgutierrez95 Жыл бұрын

@@SHONEY21Z yeah

@MrRaulgutierrez95 Жыл бұрын

It was easier to just order the whole part then try to Fidel. With it.

@MrRaulgutierrez95 Жыл бұрын

This is killing im getting ready to just throw this in garbage. For starters mine is 2 cycle engine. I have both the 2cycle and 4cycle engine torn apart. Mine doesnt have that shield. And no spring like mentioned. It biulds tension but after 3.or for start the cord doesnt wind back up. Then it gets siezed.

@SHONEY21Z Жыл бұрын

Ever figure it out?

@MrRaulgutierrez95 Жыл бұрын

@@SHONEY21Z yes