Homemade inductance meter • Diy simple inductance ...
Пікірлер: 483
@elias-rn6mx5 жыл бұрын
This guy is making real things,and he even answers to questions to explain his projects.for that reason.I subscribe.
@TechIdeasAG5 жыл бұрын
Thanks very much
@SixOThree5 жыл бұрын
Where is his explanation on how this works?
@oo0Spyder0oo5 жыл бұрын
@@SixOThree In the circuit diagram.
@Subswithnovideos-gv9qi4 жыл бұрын
@@SixOThree capacitor charges itself through battery, and transistor consumes capacitor's energy and convert the electrical signal to turn on the led, as much long power is hold by capacitor, led will be "On", once capacitor is fully discharged led turns "off" and capacitor charges itself again, and the cycle continous to infinity, that's what we call "blinking of led" the purpose of resistor is to glow led without burning it
@okaymalik80644 жыл бұрын
Is it possible using three or two light?
@acmefixer15 жыл бұрын
This 'negative resistance' oscillator uses the transistor's emitter to base in breakdown mode, which is to be avoided because it degrades the transistor. This circuit is never used in any mass produced equipment because the transistors are not tested and were not designed to be used in breakdown mode. It must be avoided to prevent damage.
@ngusi1st5 жыл бұрын
@Acme Fixer: I don't think so. Assuming the LED chokes 2V, then breakdown voltage of the transistor is max 10V, so max current thru C-E is 70mA (limited by 150R resistor), not enough to kill the transistor.
@orangeshaw23703 жыл бұрын
03:05 I would suggest a 1N4007 in series with the 3K3 Ohm resistor sothat )I electrolytic capacitors could be safety used.
@downtowngutter38755 жыл бұрын
All these fun little projects on youtube make me want to invest in some tools lots of tools
@jim89165 жыл бұрын
your presentation skills are getting better. nice little project.
@calvarycustoms66815 жыл бұрын
That looks great! Excellent strobing effect! 🚨👍🏼
@VR2ZXP5 жыл бұрын
Let me try to explain how it works. By RC = t, 3.3k resistor and 100u cap forms a time constant around 0.33s. When the cap just be charged, voltage of cap is lower than the acceptable reverse voltage of the VCE of the transistor. CE of transistor keeps open circuit then LED is off. However, once the cap voltage reaches over VCE, transistor becomes short circuit. It turns on the LED and also discharge the cap at the same time to complete one cycle operation. However, this circuit just works in high power supply voltage and the transistor may be damaged after a long time operation. To make this circuit more reliable, the transistor can be replaced by a zener diode, then using a NPN transistor which drives from the net between zener and LED to discharge the cap.
@darkshadowsx59495 жыл бұрын
I agree with the zener diode. the transistor isn't doing much other than acting like a diode. base isn't being used switch it on/off.
@casper25015 жыл бұрын
That's what I looking for :D explained very well and without this shitty music. Thanks [°√•]
@RC-Heli835 Жыл бұрын
Do you have a schematic of that? Thanks!
@gianfiat84265 жыл бұрын
Its fantastic! Many thanks!
@dodonghiphap27025 жыл бұрын
If I gonna use this in a 2v led strip what value of capacitor and resistor will I use?
@FredtheDorfDorfman19855 жыл бұрын
Someone has probably already answered this I'm sure, but isn't this avalanche pulse generation? The transistor rapidly conducts current when the voltage across the capacitor reaches the collector-emitter avalanche voltage. I thought the capacitor in an avalanche pulse generator had to be small to keep the energy from causing the PN junction to fail? Does this having the emitter connected to the positive plate, instead of the collector, have something to do with keeping that from happening?
@kenmoriyama75662 жыл бұрын
I love the ideas and I really like it! Simpoe and easy! Thank you. But, is there a way to power on in 3v-3.7v battery? What changes will be needed?
@gb5uq5 жыл бұрын
Changing the value of the capacitor alters the time constant increasing or decreasing the rate of flash.
@yononable5 жыл бұрын
superb tutorial..thanks a lot.
@damiandworecki55815 жыл бұрын
Ideal para la moto y chau relé gracias por el vídeo.
@Creativity_DIY Жыл бұрын
Must be tray to make this ideas. Love it 👍 and Thank You 🙏
@helgahuven16289 ай бұрын
COOL . SIMPLE E MUITO BEM EXPLICADO E MONTADO . PARABÉNS . VALEU
@huanphamba8583 жыл бұрын
Thank you so much, it's thanks to you that I did what I wanted
@rahulbindhu5 жыл бұрын
Good content bro, love from kerala
@adithyanv1033 жыл бұрын
ഹായ് 🤪
@aaronletchford5 жыл бұрын
Bloody fantastic thanks
@gonvindecoupe86855 жыл бұрын
good evening you liked the green led. great videos happy New Year
@naderhumood11995 жыл бұрын
Great job brother. .
@maximuspareo5 жыл бұрын
Wow , you are very generous giving us all those informations (meaning all your projects).For an 50 W (maximum) led outside projector with sensor, what modification should I do?Thanks.
@lienchen125 жыл бұрын
Thanks! I subscribed
@erbenton075 жыл бұрын
Perhaps we could skip making music videos and actually explain stuff by talking?
@gorillaau5 жыл бұрын
English may not be his first language.
@oo0Spyder0oo5 жыл бұрын
No need for the talking but no music I agree on.
@erbenton075 жыл бұрын
Then get assistance from someone who is a native English speaker. The vast majority of people watching youtube speak English.
@MokenaBob5 жыл бұрын
I agree
@alescitocp38025 жыл бұрын
@@erbenton07 r u fu....in' nuts? spanish is , actually😝😛😝😛 go get a forest and get lost ! 😁😁😂😂
@Fmacian595 жыл бұрын
Oscilador por saturación a ruptura o vavalancha, ¿es cierto? Buen video, gracias.
@ModellingIndianRailways5 жыл бұрын
Very simple and nice
@marcojaric40305 жыл бұрын
hi. I need this strobe light but powered by a 2s lipo, 8,4 v fully charged. It will work? Thanks
@Perepodvyvert_s_perevorotom5 жыл бұрын
Avalanche breakdown. Nice illustration.
@SureshKumar-nk2ok5 жыл бұрын
sir pls explain how its avalanche breakdown
@muratkayaaltn35455 жыл бұрын
A very nice work. I have a question! Can we burn more than one led diode with this circuit or a different circuit? Thanks.
@leonidaslacayo45205 жыл бұрын
If same question how many led can be added to this circuit?
@mynameisbond7113 жыл бұрын
Great, is it what I was looking for, how many LEDs can be connected to this system? How many volts does it work with?
@amitabheer2 жыл бұрын
I had already contructed the circuit with VRs too instead of Resistors to observe the blinking effect and is working fine but very strange fact I could notice but couldn't find the exact logical reason behind the issue. When I use ordinary BC547 the circuit works fine but I used the same transistor from leading manufacturers the circuit even didn't start and each and everytime same result obtained. Can anybody let me know the reason??? Thanks in advance.
@7_7_unknown5 жыл бұрын
Awesome idea
@waruna_d3 жыл бұрын
saved it for watch later bro nice!
@sawajiri1005 жыл бұрын
Can be use for RC PLANE nice 👍
@learnmore67605 жыл бұрын
Hhahahah 😂😂 input 12v rc main kahase layega re baba
@sawajiri1005 жыл бұрын
@@learnmore6760 change value of resistor from 3.3k to 2.2k ohms for 2S Battery 7.4V
@joeycarr13985 жыл бұрын
WHY NOT?
@sawajiri1005 жыл бұрын
@@tylerjames1716 fuck off your market style. Money? You can build from scratch noob!
@CXensation5 жыл бұрын
@@joeycarr1398 The circuit here only works with battery voltage above the transistors reverse breakdown voltage, which is something like 5V. (Note that the transistor is connected in reverse polarity on purpose for the circuit to work) Also the timing is highly dependant on the supply voltage. Thats why sawajiri100 suggest a different resistor value of 2.2K to still have a decent blink rate on a 2S battery. A 1S battery in the RC hobby world is one 3.7V cell LiOn battery, hence a 2S battery is 7.4V.
@maahir38715 жыл бұрын
What does a resistor doing in the circuit ? I know it resist the current. But how is it helping the circuit ? i really wanna know
@engestruturas5 жыл бұрын
Nice video! Can you explain how transistor switchs on and off without variation of potential on its gate?
@cym2475 жыл бұрын
Wonderful...Thank u...
@sergiorubiano93565 жыл бұрын
Hola, ¿ Se puede hacer con una fuente de 5 voltios?, ¿que resistencias necesitaría?
@imtheroboart5 жыл бұрын
Always connect the negative terminal from the supply first to the circuit :-)
@Kacper-ch9ds5 жыл бұрын
Why? Lol.
@JamilKhan-hk1wl5 жыл бұрын
This is not 10000v 100a supply
@imtheroboart5 жыл бұрын
@@JamilKhan-hk1wl Not necessarily. Even a 5V supply is enough to burn your components and damage your board.
@JamilKhan-hk1wl5 жыл бұрын
@@imtheroboart not if there is current limiting resistors
@calvarycustoms66815 жыл бұрын
Jamil Khan Wait, you’ve never seen a resistor flash-fry? 🤨
@Bianchi772 жыл бұрын
Nice video, thanks :)
@jpscafe76485 жыл бұрын
Muito bom! Very nice! Sp Brasil , obrigado. Thanks!
@TechIdeasAG5 жыл бұрын
Thank you very much
@jpscafe76485 жыл бұрын
@@TechIdeasAG you ar10
@moodberry5 жыл бұрын
What if I want to have a super bright strobe? Can you do a video on that?
@jamalkawabata21895 жыл бұрын
Can i use it for 9v ?. and im gonna add 3 LED's at the same time , it will work ?.
@maciejjanicki8385 Жыл бұрын
The ultimate transistor burning machine.
@richardjeun5 жыл бұрын
Collector is on the right side and emitter is on the left side; I think you need to switch the C and the E on the video. I never knew a transistor allows current to flow without any current to flow through the base.
@Alan-yd5pc10 ай бұрын
Not on a BC547, it's opposite of a 2N2222 from what I've seen online.
@kc5hgv5 жыл бұрын
Us Motorcycle guys need help with these. Can you use the clear LED and focus it with a lens so we can put this on the front of our bikes for visability.
@Francisco-ng5mu5 жыл бұрын
parabéns + 1 escrito like
@kaustubhthomare94884 жыл бұрын
How to increase / decrease the time between two flashes?
@JodBronson5 жыл бұрын
Nice!
@bestamerica5 жыл бұрын
' that nice idea... can do that work with 6 volts batterys... dont need 12 volts... what size of LED 3mm or 5mm... what BC547 to do with middle pin between C and E
@MiniTorna5 жыл бұрын
perfect man
@guillecsir15 жыл бұрын
How many LEDs do you support?
@umx615 жыл бұрын
Good job, any simple project for pulsing led ?, thx
@louwclaassens49885 жыл бұрын
What is the resistor values for Red, Yellow, Blue and White LED's?
@EAS_Alumunium5 жыл бұрын
Im using 12v led what is the resistor ohm should u use
@ghoshamit2525 жыл бұрын
Great
@PerrynBecky2 жыл бұрын
If that cell is a Li Ion cell, it needs to have a bms chip to avoid excessive discharge which would risk explosion or fire. They can be had even for a single cell, and are very cheap. A couple of dollar "insurance policy" can avoid those risks.
@OKANEHOKI5 жыл бұрын
Mantap kreatif
@earthsearchers71605 жыл бұрын
Hey, the music is repetitive and annoying. Every dam video has the same distraction. But good work 👍
@acmefixer15 жыл бұрын
So? Turn it down or off! 😕
@nhatnguyen_zen4 жыл бұрын
True.
@prashantn6875 жыл бұрын
Hi can you please help to make a Butter Churner using bidirectional motor?
@reworkingbro60555 жыл бұрын
fantastic
@gbenother87555 жыл бұрын
That's a nice simple timer circuit. Let's see it on a little circuit board instead of this "mid-air" style of construction. It's kind of cute, but if I'm mounting three of these to my RC plane, I'm looking for stable mounting, not a floppy gob of parts. Or do you pot it in RTV for rigidity?
@jimdreger46265 жыл бұрын
Are you saying that you have the ability to build an RC plane, but you can't figure out how to stabilize a few electronic components?
@moldowin5 жыл бұрын
Bought an airplane to take that transistor out and complete this video tutorial
@KarunaAnitha5 жыл бұрын
அருமை....
@alibehrouz98335 жыл бұрын
how does it works? without triggering base?
@TheMrgagan095 жыл бұрын
thenks bro nice
@mbaleloae3 жыл бұрын
how many leds can be used in this circuit?
@acex727 Жыл бұрын
Now i am going to make my own home made plane with strobe light😅
@eCitizen15 жыл бұрын
It would have been nice if you had explained why it works.
@samfosi46705 жыл бұрын
That looks like an Esaki oscilator you can check it out
@eCitizen15 жыл бұрын
@@samfosi4670 - Thanks for that info. Transistor saturation is pretty cool.
@davidjohnston53295 жыл бұрын
Thanks for that, my limited knowledge of electronics didn't help me understand how this circuit worked.
@eCitizen15 жыл бұрын
@@davidjohnston5329 - I looked it up and this transistor is being operated in a "avalanche relaxation oscillator circuit". Many transistors can be damaged by this, but it's still a neat trick.
@rajeshk1ati5 жыл бұрын
Nice job
@souravbhattacharyya3392 Жыл бұрын
Working fine... someone please explain why the base terminal is not connected to the external circuit.
@wawan24325 жыл бұрын
hahaha great job😀
@trekwong4102 жыл бұрын
Thanks 🙏 for the reference
@aksmadness87055 жыл бұрын
Hey how can I blink my 220f tail lamp like the same way, can I use the same circuit directly to a12 volt dc battery of my bike..?🤔
@starkship70184 жыл бұрын
Use realy
@soplatek5 жыл бұрын
What are the specs on the LED? 5V? 12V? How many mA?
@aniketkarhal Жыл бұрын
12v light use kr skte hai....
@EmoBoiLink Жыл бұрын
It didn't work in tinkercad circuit design, can someone help? I'm new to Transistor circuits and I used a PNP transistor and copied the exact circuit. The LED anode is attached to the emitter of the transistor. Anyone have advice.
@tejaskansara22765 жыл бұрын
Nice video Make video with 5w led flasher with 12 v dc input
@rahulghosh42894 жыл бұрын
For 5 v supply resistance used?
@tufanpolat9855 жыл бұрын
Hocam bu devreye otomobildeki 12 volt bağlarsak olurmu veya sonuç ne olur
@paccman20425 жыл бұрын
Wow esta genial maestro.!!
@eugenealemania7785 жыл бұрын
What are the materials? is it easy to do?
@shreyasmathuria7322 ай бұрын
I tried this circuit on bread board. Didn't work. Checked connections again and again. What could be the problem? FYI i am applying 9 V instead of 12 as mentioned in the diagram / video
@Samar-7777 Жыл бұрын
Can i use 12v led smd instead of single led 3v
@wellylhakim36195 жыл бұрын
very nice 👍👍👍👍
@mr.mythoclast44514 жыл бұрын
I like the old Method by using a Voltage Multiplier Circuit, then you can flash a LED even with a AA/AAA (rechargable) Battery
@soldevida83792 жыл бұрын
Can u give the link for that video
@asifriaztheexplorer65873 жыл бұрын
Did it work for 12volts led?
@derdrolftesinn5 жыл бұрын
Thanks for the Video. I wonder how the circuit works when no power is on the Base of the transistor,so the citcuit between C and E is open permanently.. can you help me understand? Greetings
@TechIdeasAG5 жыл бұрын
actually the circuit abuses the negative resistance factor in all transistor to produce the blinking effect. Here a common NPN transistor is used. When Switched On the 3.3K resistor charges the 100uf capacitor until the voltage become high enough to get emitter-base junction to avalanche. At this moment the transistor turned on quickly and the capacitor discharged by led through 150ohm resistor, and when voltage across the leads fall, the current stops, then the capacitor again starts to charge through 3.3k resistor. Thank you
@derdrolftesinn5 жыл бұрын
@@TechIdeasAG Thank you very much:-) that helped me :-)
@GFXPath5 жыл бұрын
Nice video
@pilotpaddle41214 жыл бұрын
how can I make one for 5 V input ?
@ZombieB5 жыл бұрын
just for one LED?
@gaets04 Жыл бұрын
This will work perfectly on my Airplane ✈️ models. Can you please show me how to make the same thing but a double strobe ? Shown on the ends of the wings of a 747-8 Jumbo.
@tejaskansara22765 жыл бұрын
Good for bikes and scooters with 12v
@vikashkrroke16843 жыл бұрын
4 led lagau to support kr jye gaa?
@kennethkustren93815 жыл бұрын
As a gift to all Amateur and Professional Electronics artisans, working boardless has advantages. Minimalist designs are beautiful. I wonder only why force 12V on us ?? 6V or less won't work ?? A pair of Crafters wire bending pliers might be a GODsend. Two pair even better.... one smaller, one larger ?? Another tip ... the Weller pen version of soldering iron works nicely with EXACTO BLADES.... cutting shapes and openings in plastics, shall never be gory. Be Careful... Cuts and Cauterizes too !!
@thao976vlog610 ай бұрын
Mạch chớp này rất hay
@darshanramesh41784 жыл бұрын
This led strobe can connect to bike?
@astronic45222 жыл бұрын
Nice project
@HMybach5 жыл бұрын
i try this Strobe after work today :-)
@jitendrapastaria Жыл бұрын
What changes need if we want to add 50 led
@venusmars97555 жыл бұрын
Can anyone here how the set up would look like if I wanted to use more LEDs, for example 5 or even 10 without having to make the whole thing over and over again. I want to make a warning light for a gate.