Your channel is the only one that provides detailed advice to troubleshoot inaccuracy issues. thank you for that ! ​

I am always looking forward to the next video because they are actually made to be informative and to add knowledge,this video is no exception. Keep the good work up guys 👍🏼👍🏼👍🏼

Great work as usual Jake, and very enlightening! It's good to know about the other portential causes of innacuracy, and/or pellet damage, as most of us tend to suspect a faulty mag, or misalinged pellet probe in the fist instance.

When I done this to my crown and impact I could see the difference immediately, great video jake. 👍👍

It’s great getting your videos when I’m bored👍

Thank-you so much,I have a new fx maverick which was shooting all over the place,just followed this video and now put 100 pellets through the gun hitting center everytime, really great,thanks very much.

Just about to fit a new transfer port on my M3 and had a look down it could not believe the burs. thanks for the vid.

another brilliant video guys and this alone will solve a lot of peoples accuracy issues on there M3’s..👍

Fantastically explained mate😊👌🇬🇧❤️

Another great and informative video. Are you still making the brass FX reg pistons, if so can you let me know where I can get a couple.

Thanks for posting this! Anything that helps get the pellet into the bore without damage is a good thing! I've always wondered how much damage the pellet gets from being repeatedly bashed by the shuttle and scuffed around the inside of the magazine.

Good tips and explained well. Couldn't really see an issue with the steel and brass.

Just when i thought i have done all the mods on my FX guns you show us this mate lol

Great video!!😁. That also makes a huge difference on any air rifle that's being pellet picky!!! Now to figure out a tool for the breach putting lol,,. Shrink the o ring on the way in and let go when ya pull it out👍. You'll make millions lol

I had bad issues with accuracy due to this, polishing it does wonders.

Another great video thanks 👍🏻 I have just received an impact M3 sniper .22 (fac) and taken my first 50 shots today! Weather was appalling not a good testing at all! Still, I expected it to group slightly better than it did. I understand these kind of need running/settling in first but after that, what are the first things you would do to achieve greatest accuracy? Thanks.

Having issues removing the transfer port. Heated it up to loosen the glue but it just rotates in my vice. Any suggestions?

Im just wondering! When i load pellet and remove the liner, why is that the pellet skirt is sticking out of the liner.. all my fx airgun

Excellent video. Just a quick question how easy is it to remove the transfer port with the loctite on the thread and do you put some back on when you reassemble? Keep up the great work.

For a £1500 quid air rifle I would want this done at factory. Enlightening.

Awesome tip thanks for sharing bsafe buddy

Hi got a question for you av tried FB and the gun shop can't get an answer maybe you can help I got a brand new FX Crown mk2 177 the transfer port low med and hi doesn't turn is this because its sub 12 or should it turn ?? thanks for any help/ info Derek

Nice job. Would have been good to seen footage of the accuracy of pellets beforehand and after the polishing to see the difference.

Hi another great video, You transfer port hole in the barrel looks to be oval have you done that or is it a bought item? On my dream tac it is just a round hole. It look very restricted!!

Nice vid Jeff, thanks. To inspect the pellet after loading maybe you only need to remove the mag but the rod could very easily damage head, don’t you think? Cheers and thanks again. John.

What diameter size that tranfer port.?

Hi, I've bought a new transfer port for my Wildcat hoping to cut down the number of parts with the potential to move or expand differently so I bought the longer brass version that replaces the brass & steel with one peice, I presume there is an O ring to be fitted internally although on first viewing I can't see a recess for it, if there is how do you get it in position so deep inside ?

Great video as usual, tho if we wanna be nitpicky, after all the work carefully polishing brass, it might not be the best idea to use a sharp steel tipped pin to push the inner o-ring in, or be very careful not to touch any polished brass at all. Every contact between steel and brass, brass loses. Maybe as a precaution use a wooden pick? For like shish kebab/shashlik. Yes splinters would be a B. But they can be cleaned out and you can touch the polished brass as much you want.

Hi Great content. Do you work on other peoples guns ? 😊 thanks

Hello again from a novice air gunner. I am going to install a adjustment for hammer spring in my Impact but when I try to pull out the C3 it feels spring loaded and just want to spring back in again. Is that something that is on sub 12 and in my case 10 joule? When I look at others doing the same thing they just pull the rod out. Is it something in the plenum to help with low power?

👍🏻👍🏻

What is the size on your transfer port?

FX Smooth Twist X Superior Liners are not standard for all models, some use STX in .177. I wonder why.

i was doing well, right up to the point you said undo the jam nut. this is not going to go well

Приветствую. Огонь. Всех благ

😁👌

Kind of bad QC leaving an expensive weapon to the customer in that state. But they know people like to do tweaks like this, taking the job off fx's shoulders.