Subaru WRX Cobb Intercooler & Charge Pipe Plus Grimmspeed Turbo Inlet & Boost Control Solenoid

Рет қаралды 3,954

Жыл бұрын

This video will show you how to install the Cobb top mount intercooler, Cobb charge pipe, Grimmspeed aluminum turbo inlet, and the Grimmspeed three port boost control solenoid on the 2015-2021 Subaru WRX. All parts were purchased from www.subimods.com and listed below will be links to each part.
Cobb Top Mount Intercooler With Charge Pipe: subimods.com/collections/2015...
Grimmspeed Aluminium Turbo Inlet: subimods.com/collections/2015...
Grimmspeed 3 Port Boost Control Solenoid: subimods.com/collections/2015...

Пікірлер: 16

@wilder211 Жыл бұрын

I’m waiting on someone to bring that 2018 Jeep Grand Cherokee back to your garage for a alternator and water pump video. With your detailed videos walking me through it I was able to change my spark plugs, change out brakes, and change my leaking oil filter housing on a 2016 Jeep Grand Cherokee. You have single-handedly saved me over $3000. I can’t thank you enough.

@rpangster 10 ай бұрын

thanks! installing a charge pipe, hks bpv, and GS inlet and controller in the morning

@hutchimoto1671 27 күн бұрын

Great video! Keep up the good work

@bendtheski Жыл бұрын

Great video! I'm doing the same work, plus turbo blanket in the next couple of weeks, and sure I'll be playing this back a bunch! Now if you wouldn't mind posting up a turbo blanket install real quick... FWIW, your angles, lighting and explanations are a lot better than others on KZfaq. I was starting to get burned out to all the not so helpful WRX how-to channels, but glad I came across yours!

@BLUECOLLARGARAGE Жыл бұрын

Thanks man appreciate the feedback. Unfortunately this is my son in laws car and he took it back up to Fairbanks Alaska and won’t be back down here to Colorado for awhile so can’t do a turbo blanket video.

@bendtheski Жыл бұрын

@@BLUECOLLARGARAGE so I'm about half-way done now. Turbo blanket is in with only some minor gaffs (finally figured out the mystery heat shied goes under the pulley wheel over the j-pipe), and just need to screw in and re-connect the O2 sensors. Old intercooler, charge pipe and turbo inlet are out (getting the electrical connectors to let go was the hardest part of this operation), and mounting bracket is installed. The BPV connector on the factory charge pipe didn't let go easily, and can't wait to have something less restrictive with silicone couplers. Saturday is my next garage day, and hoping to get everything buttoned up and go for a drive. Reviewing this vid one more time so I don't have to keep scrolling on the iPad in the middle of surgery. Thanks again for a really helpful vid!

@industrialmethodz 3 ай бұрын

best installation video

@brsavage4629 Жыл бұрын

🔥🔥🔥

@frias2287 Жыл бұрын

Nicr one big like👍💯

@EC-ht5og 11 ай бұрын

You need the COBB AOS as well. Keep that air inlet clear from oil. I have the COBB SF intake, COBB TMIC, COB AOS, COBB Turbo inlet and 3 port BCS, Tein Type A coilovers, ETS J pipe, COBB titanium cat back, and Megan strut tower braces front and rear, with a Faction Fab 22mm rear sway bar.

@BLUECOLLARGARAGE 11 ай бұрын

Sounds like a pretty nice setup you got going on. I actually did install a iag air oil separator heres the video on it kzfaq.info/get/bejne/gpt_rbOh2bKWnXU.html and here’s a video on the dyno kzfaq.infoOku8CxbXST4?feature=share

@760Artemio 10 ай бұрын

Awesome video bro! Very detailed! Quick question when you installed the 3 port solenoid did the car run fine? I heard you needed a tune for that part?

@BLUECOLLARGARAGE 10 ай бұрын

Yes it will need to be tuned to see the full potential of it but will drive fine until you can get it tuned.

@tyneal12 7 ай бұрын

Have you had issues with the charge pipe popping off? I installed a grimmspeed charge pipe and it popped off first pull. It also uses worm gear clamps like your cobb one does. I am going to try some t bolt clamps but just thought i would ask.

@BLUECOLLARGARAGE 7 ай бұрын

This is my son in laws car and he hasn’t had any issues with it popping off. Have you tried spraying the inside of the charge pipe with hair spray? I have done this on my Ford diesel charge pipe works like a charm forms a nice tight seal.

@tyneal12 7 ай бұрын

@@BLUECOLLARGARAGEi actually installed t band clamps today and they seem to be working. But this isn’t a bad idea either.