Super Simple DIY 10,000v AC Supply!

No video

Super Simple DIY 10,000v AC Supply!

Рет қаралды 287,323

Күн бұрын

Buy an AC flyback here: amzn.to/3CrTNTC
Buy inverter here: amzn.to/2QckzL2
PLEASE USE HIGH VOLTAGE SAFETY at all times. Not knowing your safety can incur injury. Now, lets be honest. Every High Voltage scientist needs their power supply. You guys asked for it, so we're doing it! Today we'll show you an extremely simple build that outputs over 10,000 volts AC, from a non-rectified transformer, at a relatively safe current. These transformers, from ionic cleaners, are some of the few without internal diodes. Also - Cheers to Bogdan!
Plasma Channel on Patreon: / plasmachannel
Episode 1: • How To | FIRE BEND | W...
Episode 2: • How to WATER BEND | Us...
Episode 3: • Video
Episode 4: • WIRELESS POWER | HOW T...
Episode 5: • We've actually produce...
Episode 6: • DIY FIRE TORNADO with ...
Episode 7: • Video
Episode 8: • SAINT ELMO'S FIRE | Th...
Episode 9: • IONIC THRUST | A new h...
Episode 10: • Using Water As An Elec... (last episode, water insulator)
Plasma Channel YT: / plasmachannel
On Facebook: www.facebook.c...
I am also a television actor! Follow me on IMDB
My IMDB: www.imdb.com/na...
Do not attempt to repeat our demonstrations, without prior knowledge of electrical safety. We do not hold responsibility or liability for damage or injury incurred by copying our results.
Super Simple DIY 10,000v Supply! HOW TO HOW-TO

Пікірлер: 860

@PlasmaChannel 4 жыл бұрын

NOTE: THIS VIDEO IS REALLY OLD, AND AWKWARD. Please view my newer, higher quality content!

@starchief93 3 жыл бұрын

Still good though. I used it to prove someone I know wrong, which is quite a good thing >:)

@treasuretotrash2067 5 жыл бұрын

0:30 electroboom is proud xD

@PlasmaChannel 5 жыл бұрын

ahah I bet. That shock hurt!

@facundri 4 жыл бұрын

He just made the same video, and that’s why I’m here

@Texas_bikes66 3 жыл бұрын

I didn’t know u had a yt I’m jplayz all ways watching ur tiktoks

@treasuretotrash2067 3 жыл бұрын

@@Texas_bikes66 my tiktoks?

@farewell_8450 7 жыл бұрын

It's incredible how certain things that looks some times overcomplicated are actually as easy as plugging two wires together ... nice video as always ;)

@PlasmaChannel 7 жыл бұрын

+North Thelittlefox I really appreciate the input. Yes, sometimes there are ways to circumvent a steep learning curve!

@user-in8bz3kd7d 2 жыл бұрын

@@PlasmaChannel Can you make electric boars? In our country, high-voltage electric cats can only play sneakily

@southernautodiy2643 3 жыл бұрын

I like the electroboom intro 😂

@anthonyvolkman2338 3 жыл бұрын

Yeeees!!

@shiningstaer 3 жыл бұрын

What? You sound like an idiot

@southernautodiy2643 3 жыл бұрын

@@shiningstaer i'm rubber and you're glue whatever you say bounces off of me and sticks to you

@wotblitzexe3885 3 жыл бұрын

@@shiningstaer go watch Pepa pig toxic kiddo

@thejoxter6315 3 жыл бұрын

@@shiningstaer you sound like a 5 year old which you probably are

@chems 6 жыл бұрын

3:38 its capacitively coupling to your thumb

@PlasmaChannel 6 жыл бұрын

true, nice catch!

@keeg025 3 жыл бұрын

@@PlasmaChannel it hurts if you hold it on there for to long

@styrishrodrigues 4 жыл бұрын

Who's here after electroboom..😂😂

@farlesthan1479 4 жыл бұрын

Me lol

@Anuradhai4i 4 жыл бұрын

Ha ha ha me too

@christiancoding 4 жыл бұрын

@treasuretotrash2067 4 жыл бұрын

I saw this long before electroboom did xd

@leopoldofernandezjr4441 3 жыл бұрын

@damonjackson5857 7 жыл бұрын

Hi I just came from keystone science and I love this channel already! I have a suggestion that not many people on youtube have built, and that is making a homemade x-ray machine. All you need is the x-Ray tube and about 40 kilovolts

@PlasmaChannel 7 жыл бұрын

Honored you enjoy us! As per the x-rays, I have put thought into doing so in the future. Great suggestion. I have over 80lbs of lead (will be doing a plasma-lead-melting video soon) that I can use to shield from x-rays. The trick is how to do it in a controlled fashion. Very tricky. I have the 40kv, no problem. But the tube may be a little more tricky to attain.

@mehmetinlaboratuvar7099 4 жыл бұрын

@@PlasmaChannel any vacuum tube can turn into an X-Ray tube if you apply ~10KV or more. kzfaq.info/get/bejne/h9uCl6-XnbvPen0.html

@Engineer_Anton Жыл бұрын

This man is actually serious and good with inventions I like his videos does give me an inspiration in life!

@josephd7892 3 жыл бұрын

I found out YES you have a lot of videos on voltage multipliers. Watched and gave all of them a thumbs up. I built the AC Supply in this video today and it worked perfect the first time. Next weekend will be building a 16 stage multiplier. Thank you so much for your videos.

@PlasmaChannel 3 жыл бұрын

Wonderful! I love hearing that things worked.

@josephd7892 3 жыл бұрын

@@PlasmaChannel I think I figured it out. You ran 3 capacitors in series so 3 capacitors act as one. I was thinking you did something special to prevent a voltage sag at the output.

@thatfeeble-mindedboy 5 жыл бұрын

I guess that generates lots of negative ions as well? If you don’t know about those, you should look into it... The benefits are amazing. They literally make you feel better. Generated in nature by lightning and waterfalls, they are the “fresh” in fresh air. They bond with smoke, dust, and pollen causing them to stick together and they just fall out of the air to the floor.

@nivingoonesekera 5 жыл бұрын

Nope not anymore there are research papers proving that negative ions doesnt affect any brainwaves to make you feel relaxed.

@FredtheDorfDorfman1985 5 жыл бұрын

Yes negative ion generators tend to use flybacks that feed AC into Cockroft-Walton voltage multiplier cascades with negative output that is fed to a set of needles that discharge negative ion corona into the air and a fan blows air through that carries the ions out into the room. Ionic breeze machines like this one use plates charged with the negative high voltage, and electrode wires on the upwind side of the plates with the positive charge to electrically charge and move the air, like a high voltage lifter does, and air pollutants like pollen, mold spores, dust, dust mite feces, animal dander, etc cling to the plates and can be wiped off and discarded. They clean the air electrically and disperse negative ions to improve the air quality.

@viktorpettersson6899 6 жыл бұрын

I love your videos so much. The effort, classy, instructions! You deserve so much more views

@PlasmaChannel 6 жыл бұрын

Really appreciate that sentiment. Thank you for the support!

@gogo311 7 жыл бұрын

So simple! I didn't know those ballasts put out high frequency! Also, can't believe you got that ionizer thing for 3$.

@PlasmaChannel 7 жыл бұрын

+gogo311 the place I buy most my HV supplies from... Rhymes with hood will. Yes, it was 3 or 4 dollars!

@DeepakDeepak-is9ro 5 жыл бұрын

Sir I made it! and it's Working ! Thanks A Lot Sir After this I am your Big Fan !

@PlasmaChannel 5 жыл бұрын

Excellent! im' happy to hear

@ElectricExperimentsRobert33 7 жыл бұрын

Nice video Jay :) I did not see the video notification..

@PlasmaChannel 7 жыл бұрын

Thanks! That is a problem that you did not receive a notification....

@ElectricExperimentsRobert33 7 жыл бұрын

I forgot to put the tick on your channel bell..

@mikelamb1253 3 жыл бұрын

Neither do I

@alvarofiomes831 3 жыл бұрын

kkkkk

@joshmellon390 4 жыл бұрын

Thanks for my newest salvage rescue item lol. MOT's, refrigerator/AC compressors, flybacks, whatever; every time we build a project like this we keep e-waste out of landfills. I'm going to dig through your channel now haha

@themineofglitches8567 5 жыл бұрын

Thanks best friend

@PlasmaChannel 5 жыл бұрын

Glad you enjoyed!

@burdendmist6543 5 жыл бұрын

"If you know where to look there very cheap." I'm thinking amazing? Lol

@OliviierLacroix 12 сағат бұрын

quick and potent

@juntendo6104 4 жыл бұрын

Im pretty sure that Flyback used in air ioniser has rectifier and outputs DC. There is voltage doubler built-in so you dont need as high voltage winding and reducing cost.

@starchief93 3 жыл бұрын

Actually, pulsed DC arcs (like the ones from DC flybacks) have different characteristics to them. They sound different and look different. It's pretty awesome!

@kame8919 4 жыл бұрын

- 1:30 -what is this?

@kame8919 4 жыл бұрын

@@Red-Eyed_Black_Cave_Hamster Thank you bro, i'am Romanian , i not .... Translate

@Texas_bikes66 3 жыл бұрын

@@kame8919 or if needed u can buy on amazon etc ac flyback transformer cuz that’s what your need

@Jajaho2 6 жыл бұрын

Nice outfit. Good content. Very entertaining.

@PlasmaChannel 6 жыл бұрын

Thank you for the feedback! Seen our recent stuff?

@daffster13 5 жыл бұрын

Bro, thanks, your videos have reminded me how much I used to love electricity. Now that my interest has been resparked. i can share these cool projects with my 10 y/o home-schooled son, Grant

@PlasmaChannel 5 жыл бұрын

Please share your love of science. We are limited by how many people care to invest in the science fields.

@daffster13 5 жыл бұрын

You keep the videos coming, I'll keep the neighborhood children entertained and busy with projects.

@roshannaidu6313 4 жыл бұрын

@@daffster13 heh "resparked"

@daffster13 4 жыл бұрын

@@roshannaidu6313 🤣😂🤣😂🤣

@jamesjanota985 6 жыл бұрын

Thank you Jay for keeping it real!

@PlasmaChannel 6 жыл бұрын

My pleasure! Thanks for the loyalty

@thefunnyguy16 Жыл бұрын

He finaly shoked him self in the ELECTROBOOM wey!🤣

@PlasmaChannel Жыл бұрын

Haha I've been doing that since 2004 my friend.

@_P0tat07_ 5 жыл бұрын

It’s easier to use a fluorescent ballast (the driver) that has the two yellow wires. There’s no guess work involved. Just connect one of the yellow wires to one pin on the primary and the matching color, (depending on which side you use) which is red or blue, to the other pin. Easy as that. Just saying!

@Aaron48219 3 жыл бұрын

Oh boy. You're a bad influence on me Jay. I never thought to use the guts from an ionic air purifier. Just happen to have two or three of those laying around in the basement too.

@PlasmaChannel 3 жыл бұрын

I can only hope to the the best of influences for children, and the worst of influences for adults.

@farefouse 5 жыл бұрын

buys neon sign transfromer for 30 quideru done.

@Mareupia 7 жыл бұрын

Gotta love that thriftshopping!! Fun episode Jay!

@PlasmaChannel 7 жыл бұрын

Its all about those thrift stores. I'm telling ya

@Mareupia 7 жыл бұрын

you're a man after my heart.... and my rather limited wallet

@jeffreywtoy 3 жыл бұрын

I enjoy your work Jay! Is it possible to produce more than one plasma Arc in one circuit?

@jerrytuma8972 4 жыл бұрын

How did you know it was safe to touch? And is there a way to adjust the frequency to play audio through a voltage multiplier

@youngcuzzoproductions 2 жыл бұрын

arcs are probebly so high in frequency that it dosnt shock it just burns, still shouldnt touch it

@PainStreakGamingYtAJtojbbros 6 жыл бұрын

Make your own circuit

@PlasmaChannel 5 жыл бұрын

Good idea

@ronalmanurung1647 6 жыл бұрын

this really boombastik channel

@PlasmaChannel 6 жыл бұрын

Thanks! Check out a lot of our newer episodes. There have been some very fun do it yourself videos.

@OliviierLacroix 12 сағат бұрын

love this

@nuclearhighpowerweapons7507 4 жыл бұрын

It's really nice to hold the High Voltage as long as it's not just high current.

@nielsdaemen 5 жыл бұрын

My first time on this channel and it looks to me like he was inspired by electroboom!

@PlasmaChannel 5 жыл бұрын

Haha, I do enjoy that channel. However, I specialize in high voltage generation. Something most channels only touch on.

@siegec4239 Жыл бұрын

would love to see some more of these simple videos on making supplies and circuits

@modelllichtsysteme 5 жыл бұрын

3:37 - 3:38 Watch in slowmotion and you see sparks going into Jay's hand

@PlasmaChannel 5 жыл бұрын

A spark a day keeps the frown away.

@DaxHamilton 2 жыл бұрын

Awesome video! Just starting to research HV. Quick question... is there a simple way to make the frequency of the output voltage variable?

@CoolDudeClem 6 жыл бұрын

I built a high voltage generator using a flyback, but wound a custom primary on to the exposed side of the core and used a 555 timer and a mosfet as the driver circuit, it gave arcs like this and if I put a reasonably strong audio signal into pin 5 I could get music to play out of the arc! I also built a 1KW ZVS flyback driver which gave me bright 8 inch arcs from a small flyback out of a portable TV.

@PlasmaChannel 6 жыл бұрын

Excellent! But 8 inches????! In all my years building gadgets, i've never puled more than 3" from a flyback.

@Tsindur Жыл бұрын

@@PlasmaChannel I doubt he means initial arc but rather the peak of the pull back.

@Adamisgood24 5 жыл бұрын

Flyback transformer!!

@idiotsandwich7528 4 жыл бұрын

time for a diy cathode ray tube experiment.

@PlasmaChannel 4 жыл бұрын

Here come X-rays!

@fastcyanide63 6 жыл бұрын

3:38 he gets some

@voice4voicelessKrzysiek 5 жыл бұрын

Nice job, J! I am going to do it.

@PlasmaChannel 5 жыл бұрын

Give it a try! I'd suggest looking for the Sharper Image design, as the transformer inside is the same as in my video. Try looking for sharper image designs.

@WildfoxFabrication 6 жыл бұрын

amazing!!!

@bottlekruiser 7 жыл бұрын

Isn't air breakdown voltage more that 10kV/cm? AFAIK it ranges between 10 and 30 depending on electrode sharpness and, if that's a 1" gap, it should be at least 25kV, shouldn't it?

@PlasmaChannel 7 жыл бұрын

battlekruiser great question. Air's dielectric breakdown is 30kv/cm between two 1" brass spheres. This is the electrical standard at STP. However, when you have sharp points, the electric field gradients are much more intense and longer sparks are achieved with lower voltages. The two high voltage leads are very sharp. This transformer indeed outputs approximately 10,000 v. If I attached it to two rounded spheres, the spark length is approximately 4mm

@madhumishra6066 5 жыл бұрын

Make an high voltage transformer

@victorst5997 7 жыл бұрын

The moment I saw you made a new video I had to watch it right away

@PlasmaChannel 7 жыл бұрын

I'm honored you stick with us! Thanks for enjoying our passion!

@bcikablam3578 6 жыл бұрын

I recently found an air ionizer at the thrift store, but upon disassembling, I found that there was a small box connected to the ionizing spikes. It says "input 120 vac 50-60 hertz, output 7kv dc negative." theoretically that would contain a transformer and diodes, but it could have some sort of electronic circuit. The whole air filter works anyway, so would it be worth trying to recover a transformer, or should I just use the whole thing like it's supposed to be used? and should I buy the transformer off amazon, or find/ try to make my own? sorry for a lot of questions, but I want to make sure I don't blow up my parent's basement...

@thegorazd7346 4 жыл бұрын

I have the same transformer but i use homemade ZVS driver instead, so it's more powerfull. Can i use it for voltage multiplier? Also congratulations for 100k subs

@culllaticiqsu83 6 жыл бұрын

You can find something like this on the Avasva page. Full step-by-step instructions right on your desk.

@bastienguilbaud5768 3 жыл бұрын

I like how electroboom is often influenced by Jay. This time we got to see what happens when Jay channels his inner electroboom : he get shocked :-)

@MikePoirier 7 жыл бұрын

Hi Jay, I like it. It's very simple and works !

@PlasmaChannel 7 жыл бұрын

+Mike Poirier im very glad you enjoyed the DIY. Thank you for the feedback

@musabacaku1686 4 жыл бұрын

@@PlasmaChannel can you touch this arcc

@KiloFeenix 3 жыл бұрын

Your newer videos don't have the same bedroom voice

@T.KRay-xz5ff Ай бұрын

Hahaha😂 im also here after electroboom

@tiredironrepair 2 жыл бұрын

BTW an ionic or "electrostatic" air filter is the only kind that will remove nano particulate aerosols from the air. HEPA's are good but you need the power of plasma to have truly clean air. Unless you live in a tropical rain forest or something that is.

@superswimgirl44 7 жыл бұрын

Love the videos!

@qqolcn3034 5 жыл бұрын

Except, flybacks have a lot of pins and you did not go into which are the primary that you have to connect to. Also, would have been helpful to show said trial and error. Kind of a rather incomplete build...

@PlasmaChannel 5 жыл бұрын

Not all flyback have multiple pins. Some have only 4, some have 9, some 12, some, two wires coming out of the epoxy. I focused on the concept of the build, not the trial and error. No one has time to watch a trial and error video. Hopefully you enjoyed nonetheless

@aboahmedsukk7667 5 жыл бұрын

This is nice i have made one like this but i used a hor. TR. And drive tr.

@tdtrecordsmusic 4 жыл бұрын

Serious question/request >> Can u make a mini-series called 'how not to die or blow up your stuff " what do I need to look out for to 'not get stuck' ,, to not have something across the room light on fire ,, etc etc ...

@dalenassar9152 Жыл бұрын

GREAT VIDEO!! Believe it or not, just 2 days after watching this video, I was in furniture store, and happened to see TWO of these ionizers ($5)...grabbed them up fast! Now I can build this. TWO QUESTIONS: 1) Are these transformers pure AC output..or may they have some internal diodes?? 2) Can they be connected in series for higher output? THANKS AGAIN!!!

@qqwp9937 4 жыл бұрын

*FULL BRIDGE RECTIFIER*

@user-cb2ex1zy9u 7 ай бұрын

These type of transformer can also be found in ozone generators

@eminusipi 4 жыл бұрын

I think that I recognize that device you showed in the opening. It is from the Amazing Whole Foods of electronic kits! Old Bob is still at it.

@PlasmaChannel 4 жыл бұрын

I've tried to find it online, to buy another, and they no longer exist. Breaks my heart!

@domshakespeare1582 5 жыл бұрын

hi plasma channel, just came across your channel. i'm from the u.k, had to google what a thrift store was lol. would this piece still work with a 240v supply? pretty new to this, but love it none the less. thanls

@PlasmaChannel 5 жыл бұрын

Hi dom! It should work with 240 volt as well. However, only use the CFL inverters sold in your country, for specificly 240 volt input (from wall). Basically, the output will then be the same as what would happen here in the USA. On that note, greetings from Seattle, Washington!

@nielsdaemen 3 жыл бұрын

Are you shure that flyback outputs AC? Looks just like one from a CRT wich outputs DC

@nicktohzyu 7 жыл бұрын

why is the arc AC so high frequency? shouldn't it be the same frequency as the wall AC?

@PlasmaChannel 7 жыл бұрын

Ah, that's a GREAT question! And I wish I had mentioned this in the video: that driver uses transistors to switch 120v into 300vac at very high frequencies. It's a driver, and less of a transformer. Usually any driver that uses transistors will be run at higher frequencies. Since the high voltage transformer is driven at that higher frequency, the output arc is higher frequency.

@nicktohzyu 7 жыл бұрын

Do most fluorescent ballasts do this?

@PlasmaChannel 7 жыл бұрын

Not all. Some are pure inductors which, when plugged in, give a small voltage boost to ignite the tubes. However, those types use a momentary voltage spike, at 60hz, which is unusable for our purposes. usually those ballasts are heavy, iron filled inductors.

@dash8brj 6 жыл бұрын

Also, as a bonus, the fluorescent fitting doesn't buzz at the mains frequency like the older iron core ballasted ones do. The iron core ones also wont work with the transformer out of the air purifier, as its designed to run at high frequency. Just like an old fashioned TV set flyback transformer :)

@mykulpierce 6 жыл бұрын

Looking at spec Sheet for ICN-3P32-N ballast they operate at above 42 Khz! T5 ballast operate around that ballpark too.

@hongbinbin24 7 жыл бұрын

Excellent!

@PlasmaChannel 7 жыл бұрын

Hong, your viewership is greatly appreciated. I hope you stick around!

@clarketangye5272 3 жыл бұрын

Cool video

@sammymasters7165 Жыл бұрын

heats up real fast

@velidar1 6 жыл бұрын

You can get it from old tv or pc monitors

@PlasmaChannel 6 жыл бұрын

Those are DC flybacks. They do not output AC like these from air purifiers

@velidar1 6 жыл бұрын

Hmm I have seen one as I remember ill tr to post link

@vertox4837 6 жыл бұрын

Plasma Channel there are flybacks that output AC ;)

@smashdesystem 7 жыл бұрын

That's so simple yet brilliant. I wonder how much voltage could you output with a microwave transformer instead.

@gogo311 7 жыл бұрын

MOT operates at 50Hz, it wouldn't drive a flyback transformer.

@inductor1.77 7 жыл бұрын

lmao, hook up a mot to it and youd have a good bang.

@felixboian-togyik3346 6 жыл бұрын

ka boom :)

@brianwu3566 6 жыл бұрын

2000vac-2400vac

@greenthizzle4 6 жыл бұрын

gogo311 your europe/England is showing..

@edgeeffect 6 жыл бұрын

That's cool... in the old days we'd have found a flyback transformer out of a CRT device... but in this day and age of flat screens, they're getting rare. Good call on finding an ioniser, although they're not really THAT common on this side of The Atlantic. Although a bit more explanation of WHY we're using these components and how they work would be much more helpful.

@PlasmaChannel 6 жыл бұрын

That is really interesting feedback. Are you in Europe? Ionizers are rare over there? They are all over the place in USA.

@mihirchandran 3 жыл бұрын

You can also get a flyback transformer by disassembling an old cathode ray tube television.

@amarama4725 4 жыл бұрын

The bast channel ever thank you plasma

@PlasmaChannel 4 жыл бұрын

I'm honored by your opinion. Thank you.

@amandanish8294 4 жыл бұрын

Hey Jay, can you please provide schematic of over 20kv powers supply. I am actually curious about it

@9lives950 8 ай бұрын

Bro looks like the guy from great scott

@USSBARBEL Жыл бұрын

Safety concepts? Retired Navy electrician... worked with 500 VDC & AC, but not 10KV.... Thanks!

@koevoet7288 6 жыл бұрын

Is it safe to touch?

@PlasmaChannel 6 жыл бұрын

It is!

@johnray854 Жыл бұрын

Remember the greatest enemy is the one who lives within... stupidity

@user-kn4wv2wf1q 6 ай бұрын

nice video the best

@josephhammaker2573 6 жыл бұрын

You're awesome I love your channel

@PlasmaChannel 6 жыл бұрын

Joseph thank you so much!

@spider91fc 5 жыл бұрын

A FULL... BRIDGE... RECTIFIER!!!...

@PlasmaChannel 4 жыл бұрын

A puny single diode? FULL BRIDGE RECTIFIEEER!

@kyle2015 5 жыл бұрын

Something i noticed at the end you say dont forget, the brain heard forget, maybe try remember to like and subscribe. But, Love this video and went out to buy the suplies right after thanks!

@pazetto 3 жыл бұрын

0:30 ElectroBOOM influence

@syedabdullahalbokhari5134 3 жыл бұрын

can u make plasma to destroy water bacteria?

@bentuffin6357 6 жыл бұрын

Very helpful thanks

@PlasmaChannel 6 жыл бұрын

Be safe, give it a try!

@erlendse 7 жыл бұрын

Clever, I haven't heard about that mix before. I didn't know ionizers used ferrite transformer. (but I know plasma balls do) Are you going to do more power supply videos? There is the TV flybacks, the AC stuff, mains frequency, high frequency, the safe and the deadly. And cover DC & AC and the difference in behavior? Some people seems to really overrate the voltage of Tesla coils too, also a nice topic.

@PlasmaChannel 7 жыл бұрын

I fully agree with the over ratings of Tesla Coil. Pulse rate and EM envelope drastically affects spark length... I do plan on doing additional power supply videos! Thanks for the comment.

@andresamaniego4647 4 жыл бұрын

Hey! Love the channel! I have a question.... I’ve been working on a similar project but the question I have is what exactly did you do with the remaining wires. I know the ballast has 4 output wires and you have to use 2 but did you do anything with the other two? Did you just cap them off?

@PlasmaChannel 4 жыл бұрын

Hello, thank you! Yes, I just cut them off and capped them.

@ruby_R53 3 жыл бұрын

if you definitely do not need to use the remaining ballast wires, I recommend just unsoldering them, then you will have a large cable that you can reuse

@msvnr1951 6 жыл бұрын

very nice explanation and sexy neat presentation. I believe you will become famous in the upcoming days. Question: is it a flyback transformer because it is also found in old CRT TV .

@msvnr1951 6 жыл бұрын

how to make a DC high voltage power supply ???

@thetribal697 Жыл бұрын

Going to my own diy powder coating gun with voltage multiplier

@toul100 2 жыл бұрын

You know the FCC can literally regulate what you’re doing right now

@PlasmaChannel 2 жыл бұрын

Every video of mine has been shot in an RF shielded room, with grounded mesh placed on the walls. All my filming locations have been customized, which has not been cheap. Very few of my videos involve any kind of interference producing devices as well.

@Andrey-wolt 6 жыл бұрын

You is very very very best!!!my kumir

@PlasmaChannel 6 жыл бұрын

Ha, thank you!

@electric_photon4660 4 жыл бұрын

I stumbled upon this while experimenting years ago and was able to achieve 100kV. I seemed to have gotten lucky with the flyback I used cause I couldn't replicate it with any others

@PlasmaChannel 4 жыл бұрын

It is funny how each flyback can produce drastically different results. 100kv is impressive.

@electric_photon4660 4 жыл бұрын

@@PlasmaChannel I have some really old ones that will produce arcs as big as a MOT with a zvs driver and then some that just make little sparks

@wildmanfujiami5870 4 жыл бұрын

@@PlasmaChannel i'm sure this has a lot to do with wire gauge, the Q factor of the transformer, the type of driver waveform (sine, square, sawtooth), and its natural resonance range. i built a transformer from scratch that consisted of just 1 layer of 32AWG enamel wire on an old EM choke core that was about 2.5 inches long and an inch wide that must have produced at least 20kv at the right frequency with a square wave, given the arc length

@1Stevencat 4 жыл бұрын

Very cool,

@PlasmaChannel 4 жыл бұрын

Thank you Steven

@nigel-matthews 4 жыл бұрын

I never realized the flyback transformers from those ionic breezes didn't have the diodes like the ones from CRT TVs.

@ozymandiasking173 4 жыл бұрын

i was wondering about that. i thoughr all US made flybacks were DC

@Elfnetdesigns 5 жыл бұрын

Even cheaper driver is the circuit from a CFL bulb.

@PlasmaChannel 5 жыл бұрын

True. These are quite reliable....but not high in power.

@up267 5 жыл бұрын

Really! it can kill me if I touches the arc

@PlasmaChannel 5 жыл бұрын

It will not kill, not enough power or current

@up267 5 жыл бұрын

@@PlasmaChannel thank you sir

@rkb6783 2 жыл бұрын

I'm a new viewer, could I ask a question ? Did you get this demonstration from your fourth graders teachers assistant ? I really would like to ask my grandkids grade school & kindergartner teachers assistants. To do this for each class...