SuperHandy Wood Chipper Shredder Mulcher Assembley and Given the Test

No video

SuperHandy Wood Chipper Shredder Mulcher Assembley and Given the Test

Рет қаралды 30,136

Күн бұрын

The SuperHandy Wood Chipper Shredder Mulcher Ultra Duty 7HP Gas 3 in 1 Multi-Function 3" Inch Max Wood Capacity is assembled and given the test
Checkout my Amazon store---
“As an Amazon Associate I earn from qualifying purchases.”
www.amazon.com...
Want an official Disgruntled Mechanic sticker? just send your mailing address to the email below:
thedisgruntledmechanic@gmail.com
Wanna send me a sticker or other swag? Just send it to the address below.
*****************************************************************
Mailing Address:
The Disgruntled Mechanic
P.O. Box 12
5 E Roosevelt Ave
Elysburg, PA 17824
*****************************************************************
Disclaimer:
BE ADVISED: Any public comment left on THE DISGRUNTLED MECHANIC CHANNEL may get a video response from me rather than a written response. IF YOU ARE NOT COMFORTABLE WITH THIS DO NOT COMMENT!
I am not responsible for any damage anyone does to equipment or themselves from the information contained in the video. If you follow the video and you do stupid shit to you, your equipment, or others it is your fault not the Disgruntled Mechanics! This information is given with the understanding that if you use this information you do so with no liability to the Disgruntled Mechanic or this channel. These videos are for entertainment purposes only! Due to factors beyond the control of the Disgruntled Mechanic, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. the Disgruntled Mechanic assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. the Disgruntled Mechanic recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of the Disgruntled Mechanic, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not the Disgruntled Mechanic.

Пікірлер: 101

@txsviking 3 жыл бұрын

Every time I see a wood chipper Fargo comes to mind. 🤣🤣

@TheDisgruntledMechanic 3 жыл бұрын

Ya know Helga said that and never saw it!

@Passionproject100 3 жыл бұрын

I bought one a year ago and I absolutely love it even though It is a ton of work to limb everything up, I love love love it.

@SBE3000 2 жыл бұрын

I got the single feed 3" unit and it's small but mighty so far. I limb everything before I remove it from the tree if possible. The crotches of the branches is the worst for this one but I started cutting them out with my sawsall and binning them for collection. It is more prep work but with 10 dead full grown hickory trees, 3 mulberry trees and an oak, I needed something 😅

@771blahblah 3 жыл бұрын

Not thinking of buying one now... thank you so much for this video

@geyser3445 3 жыл бұрын

I had a similar cused hipper a few years ago and it was more effort to feed the branches into the machine than it was worth, so I sold it.

@TheDisgruntledMechanic 3 жыл бұрын

If they are very staight and no real limbs works great! HA! Believe me I really debated about just sending it back.

@throttlebottle5906 3 жыл бұрын

it's more for old granny to send her hand sheared hedge trimming through lol

@FvM8 2 ай бұрын

😅 Even in the rain had me going.

@limeallens6160 2 ай бұрын

I can mark this one off my list

@dmarshall1964 6 ай бұрын

Bigbear Power 5inch chipper you would love it. Blades are always better than the disk. Good Day I know this was 3 years ago but still ones are watching it.

@zoktoberfest 3 жыл бұрын

You were shoving in 3" logs like it was a 20 hp commercial machine that professional tree cutters use. You have to go easy with big limbs

@TheDisgruntledMechanic 3 жыл бұрын

so now anyone considering buying this chipper knows that it can not be treated like a 20 hp commercial machine that professional tree cutters use!

@getitdonehomerepair 3 жыл бұрын

It looks like it will work great on the smaller pieces . I could use one of those yesterday.

@TheDisgruntledMechanic 3 жыл бұрын

yeah but it is a slow process!

@pissedoffpapa2841 3 жыл бұрын

Greetings Disgruntled Mechanic from The Pissed Off Papa, After seeing this video I think I am gonna go with a Dr power. Thanx for the heads up brother.

@TheDisgruntledMechanic 3 жыл бұрын

My pleasure!

@Boydavie123 2 жыл бұрын

I've never seen a chipper work unless its commercial. However i used the side mount hose and slowly fed the leaves in and that worked great. The top feed is stupid. The guard stops leaves completely. the hose attachment works great and the leaves are ground up to powder literally. It's the new year and i'm trying to get it started. I'm sure it will work.

@jasonfoster9118 2 жыл бұрын

I just ordered one for dead, half rotten limbs. I figured it is weak but I'm just trying to chip up a bunch of old limbs for my garden to build up the soil and mulch around everything.

@BigDog50001 3 жыл бұрын

Wow Mike that thing looks um.....Super Handy! ;)

@steveross9107 Жыл бұрын

I like it. I chopped a lot of cedar where are all curved branches. I did not push it to 3"s. I had plenty of work with just under 3". And honestly, they could have been 3 or very close. I also wish I got the different model without the shredder. The shut would have sent the chips to a better place higher up into a bin instead of so close to the ground. I got mine from Great Circle.

@AntonioClaudioMichael 3 жыл бұрын

Nice looking unit I like the orange

@samdavis5079 3 жыл бұрын

All the reasons I sold my old MTD chipper and went back to pile it up and get the Burnz-A-Matic out.

@TheDisgruntledMechanic 3 жыл бұрын

Yep I hear you on that!

@nathankane8775 3 жыл бұрын

I was just about to add one to my cart, I'm glad I saw this video. The way it barely chips wood would make me crazy.

@TheDisgruntledMechanic 3 жыл бұрын

Very reason I did the video! This was a real time test.

@nathankane8775 3 жыл бұрын

@@TheDisgruntledMechanic I really appreciate it, I have a ton of branches and limbs I want to chip up, it would take forever with that. Not to mention the fact that it keeps stalling. Again, thanks for the vid, you have my sub!

@stoneywilliams1209 2 жыл бұрын

Likewise, it’s videos like this that help people decide if a product is right for them. This thing seemed to struggle with the chore it was made to do. Thanks to the uploader!

@whodoneit218 7 ай бұрын

Like the first commenter said, you cant just throw the limbs in it! Look at the commecial units. Those actually have a feature that feeds the wood in a little at a time and stops feeding when the engine starts to bog down.

@thomasshea4466 7 ай бұрын

Super helpful. Thank you. Just bought this product and quite disappointed so far. Can’t figure out what the top hopper is even there for. It doesn’t work at all.

@mikesworld60 3 жыл бұрын

I love a good fire and some marshmellows.

@cameronpearson5459 9 ай бұрын

I have noticed the blades usually come fairly dull, sharpen first. Additionally, freshly cut oak is going to be one of the hardest wood you can send into one of these bad boys. Just my two cents.

@AntonioClaudioMichael 3 жыл бұрын

Seems kinda hard to pull start like the compression is super high

@peterp4876 2 жыл бұрын

it is good to see the video and how much work it is to feed the branches in it. The video helped me greatly in making up my mind about buying one. No thanks. I would rather burn the branches in a barrel!!

@AntonioClaudioMichael 3 жыл бұрын

Good video mike

@MegaSafariman 3 жыл бұрын

Seems like it always starts to rain just after you spend an hour getting ready to do work outside in the fall lol

@TheDisgruntledMechanic 3 жыл бұрын

Always!

@BrucesShop 3 жыл бұрын

I saw you were chewing up oak. That is tough.

@TheDisgruntledMechanic 3 жыл бұрын

To be fair yes most of it is oak

@wtbm123 3 жыл бұрын

Cool

@SteveRobReviews 3 жыл бұрын

I was just looking into one myself but to go on the back of my tractor .

@TheDisgruntledMechanic 3 жыл бұрын

If not for cost I thought od that too.

@SteveRobReviews 3 жыл бұрын

@@TheDisgruntledMechanic Ya I know almost $3K so I'll keep burning 🤣

@gabrieljacobs1344 3 жыл бұрын

It’ll do 3inch soft woods no problem. Hardwoods need to be shorter branches if they are 3inch.

@throttlebottle5906 3 жыл бұрын

I prefer the old school wood chipper, load into truck bed and haul to large burn pile. lol unless your doing tree service/major landscaping, a chipper is a waste of time until large commercial size with power feeder. everything else is weak and hand fed, use a 2x4 or 4x4 as a push stick or something else that wont fit all the way down into the cutter head ;)

@TheDisgruntledMechanic 3 жыл бұрын

yeah that would help burn all these damn ticks hiding in the leaves around here!

@jaybartgis5148 Жыл бұрын

I think I'll just rent a dumpster. Lol

@wyattoneable 3 жыл бұрын

I had to laugh at about 12:24 when you overloaded it. Yeah, it didn't like the thick stuff. I know you have a lot of clean up to do so hopefully you can work without the limitations.

@m.m.7511 Жыл бұрын

The top is for leaves...lmao

@Gideon_Judges6 3 жыл бұрын

This looks so similar to the Harbor Freight ones that I have to assume it's a rebrand. Any idea? Does the motor say Predator on it?

@plants4thewin 3 жыл бұрын

Well I guess we will see...I cut down 3 poorly maintained cherry trees on a property I just bought. I put it together tonight and will use it tomorrow. Looks like I will be out there all darn day, LOL...

@TheDisgruntledMechanic 3 жыл бұрын

I was pushing oak through it so not sure about cherry. I did notice that it seems to run and chip better as it warms up. If you put something too big in and it stalls just clear the blockage and be sure to choke it when you try to restart it even when warm.

@plants4thewin 3 жыл бұрын

@@TheDisgruntledMechanic thank you

@Nuttsy-vy7xh 3 жыл бұрын

Based on the size of the limbs and branches you were trying to feed into the machine, you probably would have been better to go to a local equipment rental service and use the $600 + dollars to rent a heavy duty chipper, tow behind the truck, that would handle all that oversized brush you stacked up. Easier on the back and in one day it would be completed.

@TheDisgruntledMechanic 3 жыл бұрын

Yep you are correct, sir! When I did this many years ago I think that is exactly what I did!

@larrabeejl 3 жыл бұрын

Stop treating it like its a commercial chipper by throwing the big chunks in it. You're supposed to feed it not throw it. This is just a bad example of user error/equipment abuse.

@TheDisgruntledMechanic 3 жыл бұрын

If it is a BAD example of abuse it means it was done correctly. If it was a GOOD example of abuse then it would be being abused. You have abused the English langauage more than I abused the chipper! And I am glad to see the wood chipper police is alive and on duty!

@dipenpujara5170 Жыл бұрын

How did you get it to stop turning around when you first started it? This happens at around 7:56 on the video

@arthurfricchione8119 3 жыл бұрын

Mike I have a chipper shredder but maybe you can give me some info. On splitting wood yes I know I need an a a LOl but. What else maybe some. Pointers on sharpening an axe. Just some ideas. I have. A lot of wood. Just had some big ones taken down. Stay well and safe. The next week should be a Dorsey. Might need axe for other things here in LINY. 😊😊😊🇺🇸 Mike you are a pisser needed a good laugh on the initial pull to start 🙏😊😊😊😊

@TheDisgruntledMechanic 3 жыл бұрын

Well I have sharpened axes but not that good at it. I do really like my Harbor Freight chain saw sharpener. For the $35 I spent when I bought it many many years ago it is well worth it! Stay safe! Oh and the 1st pull surprised me! Didn't expect it to spin quite that hard as you saw!

@throttlebottle5906 3 жыл бұрын

woah, I think you been brainwashed by the hummingbirds, working that fast :)))))

@AntonioClaudioMichael 3 жыл бұрын

What is that metal on metal clanking noise I keep hearing when the motor turns off 😳🤔

@ziks3000 2 жыл бұрын

The hammer knives for the shredder

@AntonioClaudioMichael 3 жыл бұрын

Interesting tool on the channel bro you do videos like me bro new toys on the channel not always automotive

@AntonioClaudioMichael 3 жыл бұрын

How you like that Milwaukee 16 inch chainsaw on the floor Mike @The Disgruntled Mechanic

@AnnM223 3 жыл бұрын

How much oil you need to put in?

@MetrologyEngineer 3 жыл бұрын

6:54 LOL how's that for compression.

@kirk1907 3 жыл бұрын

Maybe it needs a bit more HP Mike

@TheDisgruntledMechanic 3 жыл бұрын

Without a doubt!

@HealthSupercharger 3 жыл бұрын

yes i am not going to get such small weak machine i need to get stuff done and will go for a 11hp engine and more heavy duty machine.

@brianconnor1810 3 жыл бұрын

As you said, you should have bought a wood chipper not a shredder. A wood chipper with a drum rather than a disc would have suited your needs better for limbs. You need to hold the limbs back a few seconds to allow spinning disc to get speed back up.

@CPthetooladdict 3 жыл бұрын

Man you about flung that thing across your shop! Lol I could have used that this year my dad had a troy built that worked pretty good but man that gave you some fits good reviews mike!

@TheDisgruntledMechanic 3 жыл бұрын

Yeah wasn't quite expecting that hard of a pull!

@CPthetooladdict 3 жыл бұрын

@@TheDisgruntledMechanic well you convinced me you were a beast lol

@TheDisgruntledMechanic 3 жыл бұрын

Haha! I may be used but I ain't used up!

@CPthetooladdict 3 жыл бұрын

@@TheDisgruntledMechanic love it!!! Lol

@allens9573 2 жыл бұрын

So more time has gone by, is it still a decent machine? Im looking at the same one.

@TheDisgruntledMechanic 2 жыл бұрын

If you feed it sloooooowly, yes for small stuff.

@bodgitandleggitgarage 3 жыл бұрын

1st BOOM

@phatt_daddy1663 11 ай бұрын

you operate it like you wanna break it! ID10T Manual!

@TheDisgruntledMechanic 11 ай бұрын

just showing other consumers what it won't do. if I'm an idiot for that so be it. maybe someday I can join MENSA like you!

@m.m.7511 Жыл бұрын

She doesnt like you just slamming crap into it??? Go slow with bigger stuff...jesus....

@ncooty 2 жыл бұрын

Seems to need a lot of coddling.

@TheDisgruntledMechanic 2 жыл бұрын

Yep me and the machine!

@josephfaraci7849 2 жыл бұрын

Your technique for the smaller machines is all wrong! you just don't jam it in there you have to slow feed it! you shouldn't allow that stuff just to build up in the chutes. You're just throwing it in there you have to place it in there, and slowly feed it in- I have a different Shredder than you and it only gave me problems on Hardwood- but it was able to get the job done with a little bogging down because I slow fed it

@TheDisgruntledMechanic 2 жыл бұрын

Read comments you will see why I did it this way

@TheDisgruntledMechanic 2 жыл бұрын

Read other comments on this subjec and my answer . Not gonna type it again