We are all wrong it is service and sometimes even services!! lol one of the best KZfaq MasterCAM lessons!!
@Matthew-jz9js8 жыл бұрын
Thank you. This was easy to follow and to the point. As for the comments on your accent... The maturity of the commenters matched their icons.
@ajkennedy19748 жыл бұрын
you are a legend mate cleared some of the main errors I make
@moerichard31106 жыл бұрын
Nice vid. Easy to understand. Ignore negative comments if they knew how to do this they would have made their own videos.
@TomStikkelman6 жыл бұрын
Maurice Richard Thanks Maurice.
@Tri_Nguyen_3 жыл бұрын
Now this is how you get the boys interested !!!
@biswarupdas84806 жыл бұрын
NICE VIDEO PUT SOME MORE VIDEOS ON SURFACE MACHINING
@alanberden70213 жыл бұрын
Now say you wanted to change your start point, to a specific point where your tool starts off of the job. How would you do that? I have been running a job at my work, it has a 1.5mm crown with a 55.624mm rad being cut in G19, But for some reason when I use surface parallel even giving it an extra 20mm total offset in the parameters the 12.7mm ball end mill starts on the part. Also I am coming from the bottom up, so it is wanting to bury into a massive amount of stock. I have tweeked the Program manually to give a few more cuts in the Y axis before it does so, but would be nice if I could figure out how to do it right in mastercam lol. Thank you for the video, and for any feedback given. I also can send pictures if needed!
@pauldery78755 жыл бұрын
Great Vids....
@tanmaysamanta98593 жыл бұрын
Thank you very much sir 🙏👍 😊
@dclxvi49639 жыл бұрын
SURVICE!!!
@petecrowden54338 жыл бұрын
Thanks nice vid.
@policebox10928 жыл бұрын
good
@zakarialahmami89217 жыл бұрын
thanks
@ricardohenschl3891 Жыл бұрын
How do you use subprograms with this pls?
@bmorlok845 жыл бұрын
I enjoy watching your tutorials.. I have a question, I programmed a part that has a large "chamfer" if you will, along a radius, I used finish flow line, and have checked all settings but the chamfer appears to do small linear cuts creating facets.. how would I correct this? Thanks in advance!
@TomStikkelman5 жыл бұрын
2WN_2RBO What version Mastercam are you using?
@TomStikkelman5 жыл бұрын
2WN_2RBO What version Mastercam are you using?
@bmorlok845 жыл бұрын
@@TomStikkelman 2018.. I did research, found the filtering area, but only got it to make smaller line segments, meaning more lines of code.. would be nice to just have it create an arc..
@Artivlogs7842 жыл бұрын
I want to change your start point
@gamingwithsachin80556 жыл бұрын
Sir please 2d and 3d tool path tutorial please...
@Markitos2038 жыл бұрын
now we click on survice..
@marianodiaz4614 жыл бұрын
Hi I know that it won’t be same , but can a normal flat bottom end mill with say .5 mm corner radius be used, ?
@TomStikkelman4 жыл бұрын
mariano diaz Yes it can. The software will use whatever tool you pick
@vinodhmathi62915 жыл бұрын
How to change metric to inch
@thehallsofvalhalla27883 жыл бұрын
Question. How would you go from a block of steel to that finished shape with mastercam? I have the steel and the finished design but don't have the information in between
@TomStikkelman3 жыл бұрын
Email me your file and I can do a video on it
@thehallsofvalhalla27883 жыл бұрын
Ok! What's your email? Thanks
@TomStikkelman3 жыл бұрын
The Halls of Valhalla tstikkelman@gmail.com
@ricardoreyes-rj4hm3 жыл бұрын
@@TomStikkelman what the barrel of the gun be made using a lathe