No video
Surfboard Shaping - Rails Mark and Bend
Рет қаралды 11,942
Күн бұрынMark rails and bend them with electric planer and hand rasp.
Refine with 40/80 grit.
This is the last video 5/5 for the entire Shaping of this Surfboard.
________________________________________________
Next series will be about Painting Surfboard.
________________________________________________
Leave a comment for any question or suggestion!
I am here to ear from you 💪
Relevant TAG:
#surfboard #railbend #eps
@rooneyfamily6377 Жыл бұрын
Nice work man
@nocturnasurfboardtenerife5456 Жыл бұрын
Precioso trabajo, felicidades. Un saludo desde las islas canarias
@mrfelipehurtado 2 жыл бұрын
Awesome
@mrfelipehurtado Жыл бұрын
PLEASE MOR VIDEOS!!!
@romuyou3697 2 жыл бұрын
Too bad you don't explain where to place your landmarks and the apex!!! thank you for your video
@cerritosway 2 жыл бұрын
Thanks for your appreciation. What would you like to know exatcly? I will help you if I can.
@romuyou3697 2 жыл бұрын
@@cerritosway the video and great and congratulations for the work. I would like to see how to knock down the rails. how to draw the lines in order to cut the rails (angles)
@cerritosway 2 жыл бұрын
@@romuyou3697 Thanks for the time you spend to watch and comment. You would like to see a specific board size?!
@romuyou3697 2 жыл бұрын
@@cerritosway hi!!! No just a shortboad! see how to place the apex according to rails (boxy or other) and how to knock them down! see how to place the markers for cutting the rails. thank you for this work
@cerritosway 2 жыл бұрын
@@romuyou3697 For short board I use 2 and 4 inches on deck mark, going trough nose and tail I divided by half. On rail, starting from bottom, I usually mark it the bottom tuck at 0.4" (1cm) and the middle mark between 1" and 1" 3/8 (2.5cm and 3.5 cm). This second mark will determinate your boxy or knify rail. Is diffult to explain it on words I will try to make a video sooner.
@CarsonWilcox08 2 жыл бұрын
How do you know where to put the lines for the rails
@cerritosway 2 жыл бұрын
Hi Carson. I use 3d shape software to print rail template and deduct Marks. But on This One i went with standard Mark wich where 2 and 4 inches on deck . On rail 1 1/4 and 1 1/2 from bottom.
@CarsonWilcox08 2 жыл бұрын
Ok Thanks!!
@Frank-pj3ic 2 жыл бұрын
@@cerritosway Hi Cerritos. One question : I have Demo Shape 3D and I Can't print rails and outline. Help me?
@cerritosway 2 жыл бұрын
HI FRank! Take a screen shot of rail section. Use Photoshop or similar to scale it in real size, then print it on A4 paper.
@Thepedroportes 2 жыл бұрын
What blank did you use for this specific board?
@cerritosway Жыл бұрын
Ola Pedro! I used a BLOCK Cut peace of EPS around 30kg
@user-cp3mk7cz7i Жыл бұрын
你这个是eps内芯，还是pu内芯
@cerritosway 5 ай бұрын
EPS from block cut. Not sueprfused
Otter Surfboards
Рет қаралды 4,2 М.
Fiberglass Florida
Рет қаралды 89 М.