SURVIVOR 1980 FIAT Spider - FLOOR Rust REPAIRS
Рет қаралды 5,985
2 жыл бұрынIn this episode Nick gives you a rundown in repairing floor sections. This HOW TO video covers required tools, panel layout and fitment as well as installation.
For more videos don't forget to LIKE - Subscribe and share our channel! Thanks!
Follow us and see what Nick is up to:
invisionprototypes
invisionprototypes
www.invisionprototypes.com
Contact us: info@invisionprototypes.com
#iNVisionPrototypes #fiatspider #diy
@lemoncuda Жыл бұрын
This is the best, how to video, for repairing floor sections. I've done a few car floor pan repairs but picked up some great tips that I will add for my next project! Thanks Nick!
@iNVisionPrototypes Жыл бұрын
You bet!
@cato9tales141 2 жыл бұрын
I came back for a rerun of the trailer/lift table segment @ :35 . Great for having to do welding and rust repair to the underside.
@iNVisionPrototypes 2 жыл бұрын
It works very well !!
@tramptruck4859 2 жыл бұрын
Very presentable repair panels. For flanging the edges and punching plug weld holes I use a joggler. Sort of like pliers with a rotating head,punch on one side, step die on the other 😃
@iNVisionPrototypes 2 жыл бұрын
For sure, he did a nice job shaping them up. The joggler is a great tool, either hand operated or pneumatic! Would be a great addition to a guy's tool collection if they are planning a floor repair.
@billmiller7138 2 жыл бұрын
About rust free for a Spyder, that's a nice one!
@iNVisionPrototypes 2 жыл бұрын
He did some serious searching before coming across this one.
@joell439 2 жыл бұрын
Excellent presentation of what an average joe could accomplish with reasonable expectations. I really enjoyed watching along. Always inspiring. Clever trailer body stand too. 👍 Thank you. On a completely separate subject…. How fast was that wind outside whistling through your shop? 😳
@iNVisionPrototypes 2 жыл бұрын
We seem to be getting stronger winds more often here in Niagara. Prevailing gusts hit the big doors head on and no matter how the weather strip is adjusted we still get that whistle. Glad you enjoyed the video!
@midnighttutor Жыл бұрын
Do you have any tips or secrets for using those electric shears? When I cut a flat 18 gauge sheet I end up with wavy edges. Thank you very much!
@iNVisionPrototypes Жыл бұрын
Could be several things causing this. You may need to adjust or replace the shearing tips - should be a set screw on the lower fixed portion...unless the actual reciprocating slider is worn. If it's just on one side cut the sheet so that the drop ends up with the wavy edge.
@cato9tales141 2 жыл бұрын
Your seam sealer recommendation? Thank You. 8)
@iNVisionPrototypes 2 жыл бұрын
Hi Hans, Go to your local automotive supply store and see what's available. We use 3M, but no longer carried due to supply issues. The jungle website also carries products, just depends what you want to pay. I would advise against tar. I'll show you why in an upcoming project. Thanks for watching!
@cato9tales141 2 жыл бұрын
@@iNVisionPrototypes "jungle" 8) thanks!
@keithlanning7381 2 жыл бұрын
Where are you located
@iNVisionPrototypes 2 жыл бұрын
Niagara Falls, Ontario Canada
ELDEST Builds
Рет қаралды 2,8 М.
iNVision Prototypes
Рет қаралды 8 М.
The Grand Tour
Рет қаралды 427 М.
6th Gear Garage
Рет қаралды 331 М.
ELDEST Builds
Рет қаралды 1,3 М.
Number 27
Рет қаралды 155 М.
V12 VGT7 SHORTS
Рет қаралды 6 МЛН
НОВОСТНИЧОК
Рет қаралды 924 М.