Suzuki Boulevard C50 shaft/final drive replacement and disassemble (worn splines/ gear)

Рет қаралды 12,724

YOLO LIFE Adventures Before Dentures

Жыл бұрын

How to remove Suzuki c50 rear wheel
• Suzuki boulevard c50 r...

Пікірлер: 51

@ronaldadventuresantos7220 Ай бұрын

Wonderful, thanks for the video. I love Japanese motorcycle. I love that you have tubeless wheels

@josephharris1869 2 ай бұрын

Thank you brother !! Putting mine back together today

@rocxylemmon8535 3 ай бұрын

Thankbyou for this! You have a great spirit to do this to show us how to keep these bikes on the road.

@mccslawg 8 ай бұрын

Thank you! Great video. I have a 2014 C50 BOSS. I love this bike. Your video I will save if and when I need to take on this job

@jnetane Ай бұрын

Great video! Thank you

@abelgonzaslez2103 Жыл бұрын

SO GREAT THANK YOU MUCH .

@pd8559 Жыл бұрын

Most excellent video. Other than the final drive what else has typically needed replacement by 30k miles?

@Yololife813 Жыл бұрын

I would check drum brakes, front brakes, coolant, bleed brakes, if clutch seems to slip relplace that too, spark plugs. Basic maintenance. Owner manual can be found on website.

@AlexandreKlafke20 Жыл бұрын

Thx for the nice vídeo!

@alisaleem6988 8 ай бұрын

Here you can explain how to open and change the clutch valves of a Susuki Boulevard C50 2007 bike.

@keithnguyen1436 11 ай бұрын

Excellent video. Where did you get the whole final drive assembly and how much if you don't mind me asking?

@Yololife813 11 ай бұрын

eBay. I think it’s $100

@JooKed 10 ай бұрын

Question, how did you get the female coupling holder nut off? I'm talking about the one with the folded lip you need to pry open, but you need to hold the assembly in place to take the 22mm nut off, how did you manage? Vice?

@Yololife813 10 ай бұрын

I used my impact wrench

@wesrutkowski5564 4 ай бұрын

I have exactly same problem , when you received the new drive shaft assembly was the shaft firm and not loose and wobbly like what you showed on this video?

@Yololife813 4 ай бұрын

It was loose but not much like the one on the vid

@wesrutkowski5564 4 ай бұрын

@@Yololife813 thank you

@robinson_crusoe_ 9 ай бұрын

Hi there 👋. I start reassembling all of this final gear unit yesterday and had a question. Maybe you know how that bond 1207B should be applied? There are 2 holes for breather on final gear case. Thank you.

@Yololife813 9 ай бұрын

Sorry I don’t know how’s that bond or how to apply it. I just replaced the entire shaft drive.

@olheghtt 11 ай бұрын

It looked to me like there were five bolts to remove that frame + the one bolt with the hex head, do those six bolts have a torque spec or do they just going tight with blue thread lock... Same question for the three acorn bolts.

@Yololife813 11 ай бұрын

I believe They all have torque specs. You can Google it I just hand tight them.

@olheghtt 11 ай бұрын

@@Yololife813 I'll double-check my service manual, Haynes manuals are not all that well written.

@ChristCostanza 10 ай бұрын

Where did you find the whole final drive assembly like that? I am having the same issue and I'd like to replace every like you did, but the only whole assemblies I've found have the same issue...

@Yololife813 10 ай бұрын

eBay

@alexandremiro Жыл бұрын

Great video ! How long it took you the whole thing ? I see you take off your pullover while putting back the shaft in the yoke (that drop down a bit) and the video is cut. How did you do it ? Thank you

@Yololife813 Жыл бұрын

Took me little over 5 minutes get the shaft in.Just have to rotate the shaft and angle down. It will go in eventually

@alexandremiro Жыл бұрын

@@Yololife813 Thank you !

@alexandremiro Жыл бұрын

@@Yololife813 And what about the whole thing ? How long it took you more o less ?

@Yololife813 Жыл бұрын

@@alexandremiro probably little more than 2.5 hrs. If I did have to do the video, probably 1.5 hr

@alexandremiro Жыл бұрын

@@Yololife813 Thank you !

@user-gb9rf8fk2g Жыл бұрын

Great job. May I know the part number that is not working?

@Yololife813 Жыл бұрын

I ordered on eBay the whole used shaft. There was no part number. If you need part #go on partzilla.com and look up part number on their site.

@user-gb9rf8fk2g Жыл бұрын

@@Yololife813 thank you so much

@collosus81lash98 Жыл бұрын

Good video. How many miles do you have on it?

@Yololife813 Жыл бұрын

30000miles

@madhanakumar6155 Ай бұрын

Nice video clearly briefed fr replacing final drive shaft. Where is the EBay need full address & contact # for my future requirement if any. I own c 90, boulevard is good bike from Suzuki.

@Yololife813 Ай бұрын

eBay app you can order anything on there. Just do a search

@ronaldadventuresantos7220 Ай бұрын

I need to find tubeless wheels for my boulevard 08

@Yololife813 Ай бұрын

Try eBay?

@murcielagosky 4 ай бұрын

Just today, it happened to my wife's 2009 m50. Question. If you buy a used one from eBay, how would you know that it won't happen a year later again?

@Yololife813 4 ай бұрын

You won’t. It’s just a chance you have to take. Ask the seller how many miles is on the bike when the shaft came off. The less miles the better. When you get the used shaft inspect and put grease on the splines before install it. Good luck

@alisaleem6988 8 ай бұрын

Where is the predecessor of the engine operating, Susuke Boulevard, opening and installation diagram