Suzuki GS450: Carburetor Rebuild

Рет қаралды 12,736

5 жыл бұрын

Time-lapse of carburetor rebuild (not a tutorial)
OH! and i used Teflon (plumbers tape) to build up the exterior of the T outlets so they fit nice and snug in the carbs =)

Пікірлер: 18

@bren42069 2 ай бұрын

sweet. i have a set of those taken apart on my bench right now. some very smart person who had the bike before me put the wrong needle and seat in mine. so i'm waiting on parts that are hopefully the right ones 😅

@dane4890 Жыл бұрын

Love it, thanks!

@brocksherwood6757 4 жыл бұрын

Where would you recommend getting a entire rebuild kit for these carbs at?

@nakoawarrior3186 3 жыл бұрын

Rusty Riders 203 Mount Vernon Rd, Newark, OH 43055, very affordable parts,......1 740 522 8875

@gustaafvries 2 жыл бұрын

What is the size of the jets that you have installed in the carbs ?

@ViezeVingertjes 4 жыл бұрын

Hi, There are 3 lines going into the carbs right? The two visible on here and one from the top. Where are those going to/coming from? Is the black one the fuel line? What are the transparant ones?

@ricardoperez7975 3 жыл бұрын

I have the same one, what are the transparent ones, they will go to the fuel tank vacuum one?

@hc807 3 жыл бұрын

Great Video! What model and size are these carbs. Thank you

@bren42069 2 ай бұрын

mikuni bs34ss

@terryerickson4786 5 жыл бұрын

What was the float height. I have mine at .22mm but the hit the carb before the needle valve gets shut down.

@SaniveK_ 5 жыл бұрын

Mine did the exact same thing! I had to manually adjust them by feel =\ High enough to close, and not too low so that the floats would get stuck open. Start with the .22mm, then adjust so they close but don't get stuck. Trial and error really. In the end, I tested them at multiple different angles before re-installing them. Hold them right-side up and test the floats with your hand. You'll get the feel of where it needs to be. When you get one set right and tested on the bike, DON'T TOUCH IT! I got the left carb functioning well, but it took a few more on-and-off-again's before i got the right one correct. Don't give up and get frustrated! I just about gave up like 5 times, but stuck with it and finally found that sweet spot. Bench syncing got them close, but I used a homemade tool to dial them in. (two bottles with colored water and hoses that go to the sync ports. Here's a good example of one in action: kzfaq.info/get/bejne/baqPmZNmxMebZI0.html )

@terryerickson4786 5 жыл бұрын

@@SaniveK_ Thanks, i believe i will make one of them bottles. Pretty slick.

@hunterreid1081 4 жыл бұрын

Where did you find your rebuild kit?

@SaniveK_ 4 жыл бұрын

The bowl gaskets on mine were actually in good shape, so i just ordered am O-ring set from here > www.cycleorings.com/

@SirGuidemere91 Жыл бұрын

What snap ring pliers did you use?

@SaniveK_ Жыл бұрын

They are generic pliers I found at Harbor Freight.

@sergeantraven3015 2 жыл бұрын

What do the transparent hoses go to?

@SaniveK_ 2 жыл бұрын

Those are "exhaust" lines that just hang down behind the engine. I never saw anything come out of them... like ever, so I removed them. Not difference =)