keep the engine in the frame. Suzuki s40 head gasket requires angle grinder corner from top fin of head cylinder on passenger rear side. once you get to remove the head pull up and rotate clockwise (top view) around the tall bolt.
Пікірлер: 38
@snowreaper49533 жыл бұрын
Awesome video! My 2013 s40 just hit 55000km the other day will look at getting this done shortly!
@jettran4465 Жыл бұрын
Have fun!
@jayerwahlgren47353 жыл бұрын
Incredibly helpful video boss thank you
@jettran4465 Жыл бұрын
Glad it helped
@motoirek5908 Жыл бұрын
😀 I love Suzuki Savage 👍💙
@libertylove417811 ай бұрын
Legend, sweet video. I recently did an oil change on my 2013 S40 and a skinny toy like spring was connected to the back of the magnetic drain plug. The engine doesn’t sound bad or have any rattling noises. What would it be from? And before this situation occurred, my motorcycle in full throttle could do 88 mph and now I can only do 70 mph what could make this great loss of power? I already did an oil change and installed a new spark plug within spec. The bike is 200 miles shy of 7500 miles. I am currently waiting for a new battery and to clean & oil the K&N filter.
@michaelelse9328 Жыл бұрын
💥 S 💨 A 💨 V 💨 A 💨 G 💨 E 💥☮️ Best wishes from Germany! 🤞🏻🕊☮️
@JuanatorF Жыл бұрын
Buen video. Gracias. Recomendacion. Mas facil sacar el motor. Saludos
@DrDnepr3 ай бұрын
Very nice I have to change the camchain nice guide so far ....however I read you are not supposed to turn the engine counter clockwise ... Also why would you use sandpaper on the engine all the small particles ect can get into everywhere ... But yes very nice ... Thank you for sharing !!
@michellesaved79222 жыл бұрын
Hi that was a Great video... Thank you Very much... I would like to say some of it was faster then I can see. I wish I could have heard your comments and it would be nice to know what solvent you were using... I'm knew... I hope this feedback is helpful...
@jettran4465 Жыл бұрын
Any cleaner solvent you use shall be good enough or equivalent
@paulsavage4777 Жыл бұрын
26th minute is so precious LOL!😆
@luizgiao652 Жыл бұрын
The issue is in another spot, I suspect in the pug inside the head, and the poor air gasoline mix, carburetor may be readjust whith major main jet, to avoid execive heat.
@youfritter Жыл бұрын
too lean? I have seen vids pointing this out with the LS650
@luizgiao652 Жыл бұрын
@@youfritter yes, is the point.
@zoesantiagomichellecortezp5040 Жыл бұрын
Hey como estas? Me podrás apoya, necesito el manual de taller de este motor precisamente.
@eduardogil83382 жыл бұрын
Hey what is the jose in 1:57 for? Does it connect to something or is it a vent hose??
@jettran4465 Жыл бұрын
Sort of a vent or breather line
@dudebro88114 ай бұрын
California models (apparently) require the hose because of emission laws, it connects to a charcoal filter. There should also be an intake beneath the seat that pulls into the same filter. From the filter it goes into the carb.
@mattswenson81293 жыл бұрын
Where did you find the torque specs for the head bolts? SOS
@jettran44653 жыл бұрын
To confirm, the 4 head bolts that connect the head to the cylinder, and not the 18 bolts for the cylinder head? 8mm are 27Nm and 9mm are 33Nm
@danielfonsecarodriguez61523 жыл бұрын
@@jettran4465 and 18 bolts ? How much is it?
@jettran44653 жыл бұрын
@@danielfonsecarodriguez6152 28 ft-lb for head and 8 ft-lb for head cover. Go slow> hand tight> 10 ft-lb around all> 15 ft-lb around all> 20 around all> 25...
@davidblacksherkey87263 жыл бұрын
You should voice over what everything is and does and start a school type of channel
@jettran44653 жыл бұрын
not here to teach.
@karinadevega8994 Жыл бұрын
El cilindro sale sin usar la amoladora, no es necesario devastar las aletas de refrigeración
@jettran4465 Жыл бұрын
I tried for a hour to remove without the clearance, one corner cut on the fin isn’t going to affect the performance.
@claudiogalvez4682 Жыл бұрын
Como recomiendas que se remueba?
@pablolachmann7044 Жыл бұрын
Thanks, why did you speed it up? KZfaq allows to speed a video up to 2 times if you want. Now it's very stressfull to watch.
@Comin_at_U_Live Жыл бұрын
KZfaq allows you to Down the video down so is not so stressfull for your sensitive feelings..
@pablolachmann7044 Жыл бұрын
@@Comin_at_U_Live lol
@Comin_at_U_Live Жыл бұрын
@@pablolachmann7044 I know right? I even slowed it down to 0.5 half speed & 0.25 quarterspeed
@youtellmegod3 жыл бұрын
I don't suppose you happen to Live in Ohio?
@jettran44653 жыл бұрын
Need someone to turn a wrench for ya?
@youtellmegod3 жыл бұрын
@@jettran4465 Yes I do! R U in the usa, OHIO?
@TheBassmaster163 жыл бұрын
@@jettran4465 what about Alabama ? I would pay you good money to come help me out.
@jettran44653 жыл бұрын
@@TheBassmaster16 The video is a tutorial. I believe in you to get it done.