2007 GMC Acadia Service Stabilitrak - No Traction Control

2007 GMC Acadia Service Stabilitrak - No Traction Control - English Part 1

Рет қаралды 177,338

4 жыл бұрын

Our Acadia was towed home after displaying messages Service Stabilitrak, No Traction Control, and Service Traction Control. After using a scanner, the following codes are stored: P0011, P0014, P0021, and P0024. They all are related to the camshaft variable timing solenoids. Also HCAT, AIR, and EGR monitors are not working.
In this video, I tackle the common problem of a clogged PCV Valve (Positive Crankcase Ventilation).
A clogged PCV valve will make the engine to start vomiting oil to the snorkel before the throttle body. This can also clogged the MAF sensor (Mass Air Flow), the throttle body lever, the throttle body position sensor, which would give us the failed monitors for emissions.
Also, the same problem would cause a low oil pressure inside the engine and not enough oil to reach the camshaft solenoids...which would trigger the four codes I am getting.

Пікірлер: 78

@jamiefurman1478 3 жыл бұрын

Thanks so much for the video! I just recently had all the same readouts as you did. I figured that the stabilitrac was controlled by the brakes and checked my brake fluid level. It was low. Filled it to proper level and bingo, everything works fine now! BTW my PC valve was dirty like yours! I got a little aggressive and broke one of the lines! Whoops!

@mahshawky777 4 жыл бұрын

Thank you very much I have fixed my vehicle GMC Acadia 2011 after I watched your video and I have learned a lot and now I am more familiar with my vehicle, thank you again.

@robpeters5204 3 жыл бұрын

Very good video. The only thing I would have done differently was to put the oil cap back on the engine instead of cramming a shop rag into it. Keep up the good work!

@anastasiavargas884 2 жыл бұрын

hello hopefully when my hubby gets to remove the pcv that will fix the issue w have on our acadia.thnk u soo very much.really helpful n detasiled video .god bless

@MsFaus75 4 жыл бұрын

Hola muchas gracias, fue de mucha ayuda,, estaré pendiente por más vídeos, Gracias. Saludos.

@svca12218 4 жыл бұрын

Faustino que bueno que te ayudó.

@itzdragonlover1800 3 жыл бұрын

@@svca12218 tengo una 2010 no pasa de 25 a 30 millasgmc

@XxnosmanXx Жыл бұрын

Nice video brother, thanks for sharing. Helped a lot

@hectormorales565 Жыл бұрын

Oil in the throttle cone is due to a clogged crankshaft breather in the back follow the top hose

@steamistry3740 3 жыл бұрын

I have a 2009 GMC Acadia awd and I can’t get the p0011 light to go off. I changed all 4 vvt solenoids I changed the pvc in the back of engine I put new oil pressure sending unit and new purge valve canister. Car drives good but light won’t go off I reset it and it comes back

@mattkubiak1153 3 жыл бұрын

This was excellent. I had so much gunk in my manifold exhaust. I replaced the PCV valve in the back, cleaned the throttle body, cleaned the mass air flow sensor....but still getting stabilitrak and traction warnings. It only happens after i have been driving for a while then stop. Within 15 sec of stopping the warnings come back on. Doesn't seem to affect the performance or anything. Not sure what else to do.

@svca12218 3 жыл бұрын

Hello Matt, I did this video b/c I was getting all the other codes. Once I performed the fix; they all went away. Almost a year later, now I am having the stabilitrak and traction messages again. Like you, without any problems to the performance but triggered when stopping (the message goes away when turning off and on). I have investigated and these can be triggered by many issues. One could be a faulty break pedal sensor; or the famous wheel speed sensors. You need a GM2 scanner to pinpoint these...I bought a knock off chinese scanner to help me fix this but I haven't gotten to it yet....check out this forum...they talk about the speed sensor and how it can be dirty and be cleaned: www.acadiaforum.net/threads/question-about-the-wheel-speed-sensors.13286/

@brandonwarner2881 Жыл бұрын

FIXED! My 2014 gmc acadia slt was showing traction control off and service stabilitrak after just a few mins of driving after about 35mph if I accelerated more than 1/3 throttle the truck would cut power in quick intervals making the drivetrain shake hard. So after finding that my brake switch sensor was always triggering the lights to be on and it had to do with the slack that built up over the years in my brake peddle... changing the sensor wouldn't fixed the problem... so I added a small piece of plastic to the sensor to fix the problem. I've been driving it alot over the last few weeks with zero problems! Hope this helps someone.

@shumuinia_drinks Жыл бұрын

Hi help me please . Can you elaborate on what exactly you did because I didn't really understand it

@navaranderson8812 4 ай бұрын

HELP

@prettylady8867 3 жыл бұрын

Can you fix my Acadia lol u did awesome job

@alexlopez9803 Жыл бұрын

The tubing on my truck is in two pieces, how should I like for it when buying it??? What’s that part called, thank you… video very helpful…

@clasicosdelasmejoresepocas7347 2 жыл бұрын

El mio tiene el mismo problema pero ya no arranca !Que debo hacer?

@redberg79 2 жыл бұрын

Cool. Thank you.

@Tashkass11192 4 жыл бұрын

I have a GMC Acadia 2008 and I’m always getting those signs. What I had changed recently was the accelerator. But now when it on and on park smoke come out of the hood. Not when I’m driving only on park.

@jasminevarela2464 3 жыл бұрын

I have the same year abd make and it over heats all the time

@Tashkass11192 3 жыл бұрын

jasmine varela haha mine when it rains it stops working.

@cruxinterfaces 4 жыл бұрын

You're a professional installer, you should try using our products on your vehicle Thank you for the content

@christopherhayles2393 3 жыл бұрын

Your parts are too expensive and not good

@JoeWorker-em3jp 4 ай бұрын

I replaced the brake light switch behind pedal. Found that the brake lights were either staying on or were strobing when pedal was released causing stabiltrack msg All good now

@jwhite_og8314 2 жыл бұрын

I have the same readouts and will be doing this to our Acadia. But when ever I'm driving and turn left I get a horrible grinding noise and at the same time I get stability Trac and Traction controll off then the grinding goes away I thought it was the brakes but it isn't checked all pads and rotors.

@sindellis 2 жыл бұрын

Just saw your post, not sure if you found the problem, check your abs cable on your bearing, also the bottom cable to see if its worn, that may solve your problem

@purnapulami7648 5 ай бұрын

Same thing happened to me. When i start and start driving and applied brake grinding noise and brake shake my feet feel like ice in between rotor and pads but when i rech speed of 35mph the stabilizer trak and abs light comes on and when i parked and turn off for few minutes and start the message comes off and both sign turn off .same-thing repeat after driving.

@KopperstonedKidd 3 жыл бұрын

Mine just went off the other weekend im cryn

@owsowmuskwanaistus9213 2 жыл бұрын

That hole is caused by the beauty cover banging and rattling against it Soni just put some protection on the tube

@joshgoodman6891 Жыл бұрын

I have these same codes come on after I bought my 07 acadia.. it also goes to 3 4k rpm b4 shifting. I thought it was the transmission going out... I checked the where the airr filter hose goes and oil is everywhere in it.... there's no check engine light on tho?.

@dakotabammer9036 Жыл бұрын

Does it shake real bad when coming to a stop and does it feel like it takes a whole block to get it up to 30 mph?

@joshgoodman6891 Жыл бұрын

@@dakotabammer9036 Yes

@shumuinia_drinks Жыл бұрын

Hello, please help me. Acadia 10th year. 215 km mileage. High fuel consumption. I replaced the spark plugs, the valve cover gasket, cleaned the valve covers, cleaned the pcv valve, replaced the plunger, cleaned the throttle valve, and the hoses that go to the plunger. There was also oil in the air hose, I also cleaned it. But the fuel consumption is too high. I think it has to do with high engine revs. Which does not slow down when changing gears and coasting without gas. What do you think it could be or some sensor or regulator could be broken?

@svca12218 Жыл бұрын

did you disconnect the battery or changed throttle body? When disconnecting the battery or changing/replacing/cleaning the throttle body you have to follow a GM relearn procedure. It can be done with the expensive tablets at a mechanic/dealer shop or look for GM throttle body relearn procedure in google. (start the engine,, let it idle in park for 3 minutes, then turn off, etc...) make sure you use a timer. I had to do this several times in mine to get rid of the high revs. Cheers.

@shumuinia_drinks Жыл бұрын

@@svca12218 wow i try it

@shumuinia_drinks Жыл бұрын

@@svca12218 yes I removed the throttle valve for cleaning because it was very dirty because of the valve, but I had high revs even before cleaning

@shumuinia_drinks Жыл бұрын

Hi guys. I did this job I taught the throttle twice. In my opinion, there are minor improvements, but. In the range of revolutions 1900 - 2200 There are slight jolts. This is especially noticeable on the cruise control, when the car constantly drives in this range, it constantly coughs. Then it switches to a lower gear, increases the revolutions and accelerates. Very similar to the exhaust gas recirculation valve problem but this valve is new and the system has been cleaned. It seems that some sensor is not working correctly. Please share your thoughts.

@jakestock11 4 жыл бұрын

Looks like I am the 8th person to view this... is there a part 2? I recently had the motor out of my Acadia and replaced the timing chains and tensioners. After re-installing the motor trans K member the Stabilitrak and traction control codes are now coming up. Seems like this could be the same issue I'm having... did you end up pulling the variable valve timing sensors? Did you replace them or clean them?

@svca12218 4 жыл бұрын

Hello Jakestock11. Yes there is a part 2. I might upload it today. I replaced the PCV valve and opened the holes to GM suggestions (5/64 bottom and 7/64 top). Reconnected everything and that got rid of all 4 solenoids codes. But right after that, it developed a knocking sound coming from back of engine and many more emissions monitors are out...my wife did tell me about this intermittent knocking sound...she drives the car...I tested the fuel purge valve and I am replacing it today. Parts store had to order it and I am picking it up today. Hopefully that will be the end of it.

@eyetaser 4 жыл бұрын

Dewi Raimundo did that repair the knocking noise?

@svca12218 4 жыл бұрын

@@eyetaser Hello Taylor...watch part 2...the knocking noise was the fuel purge valve. Cheers.

@greglanford4049 2 жыл бұрын

Mine read all the same codes. When my arcade reaches 50 miles an hour it starts shaking. Any ideas?

@svca12218 2 жыл бұрын

really hard to pin point the problem without reading the codes. Engine must have three ingredients to work perfectly: electricity (spark); fuel, and air. One of those is not being supplied correctly and you have problems.

@joseb5900 3 жыл бұрын

What was the part that fix stability track

@gilracho2245 Жыл бұрын

Adding break fluid fixed mine.

@robertcarlton8712 4 жыл бұрын

Hello. I’m curious how the fix has worked since you made the video. Did it do away with the stabilitrack warnings permanently? Also, I did this fix on my Acadia and now the throttle is sticking open. Any suggestions? Thanks.

@svca12218 4 жыл бұрын

Hello Robert. Since the fix, the problem didn't come back for me. Please know that these "newer" cars have many "resets" that must be done with a powerful handheld tablet/computer. One must have access to one of these tablets in order to reset the throttle angle to the correct number....my local dealership charges $150 just to do that....I was able to buy a VXDiag GM interface to connect a laptop to the vehicle....it comes with a knockoff GM software that lets me do many things without going to the dealership: reset throttle, test circuits, and see live data....adding a subscription to ACDelco TDS (technical delivery system) for 3 days for $57....lets you reprogram modules if needed. If your throttle is sticking I would look for a new part in rockauto.com it should cost about $120....but please keep in mind...many repairs for this model require that expensive computer to reset values. I am just a DIY mechanic and now I have seen the need to upgrade to that interface and later I will need an automotive oscilloscope also. Cheers.

@christopherhayles2393 3 жыл бұрын

Good job but show all details of how you take things apart and reassemble

@svca12218 3 жыл бұрын

Thank you for the comment. I try to keep the videos under 20 mins.

@kwameboateng2578 4 жыл бұрын

Great video but it would have been nice to leave a description of the parts and items bought for reference.

@svca12218 4 жыл бұрын

Thank you for the idea. I will add the part numbers to the description of this video and then on the video for future ones. Cheers.

@ronyvargas7401 4 жыл бұрын

Hola yo tengo El mismo problema con mi carro Saturn Outlook 2007 si se soluciono El problema que tenia con con lo que le hizo disculpe?

@Rick-id3re 2 жыл бұрын

Where did you get the tubing from mines broke need help pls

@svca12218 2 жыл бұрын

Hello Rick, I took the tube to Autozone and luckily they had a replacement. Do the same, they might have something the same diameter, maybe not rigid, and you would have to cut it. But it is just an air tube. Cheers.

@davidcobarruvias4185 3 жыл бұрын

Did your cluster also go crazy ???going up and done ???

@svca12218 3 жыл бұрын

Yes...look for throttle body relearn manual process...that will be for the computer to relearn the opening of the throttle body butterfly.

@jimmycastle5095 3 жыл бұрын

How much should this cost me to have done? Thanks

@iliavoronov9468 3 жыл бұрын

Before you do all that. check the gas cap!!!! It causes all those issues!!! 10 dollar fix

@frankierose7228 3 жыл бұрын

What about the stability issue?

@svca12218 3 жыл бұрын

both messages Traction Control Off and Service Stabilitrak disappeared after I completed all the work in part 2.

@dreamteam8481 4 жыл бұрын

I recently had my 2009 GMC Acadia worked on. Had the timing chain replaced, before and after the timing chain was replaced the warning for service stabilitrak, all wheel drive off and traction control off were displayed. I had the car for 24 hours it ran fine. Now it won’t start, no clicking or anything. Everything is connected right and starter and fuses are fine. Any help?

@alma2369 3 жыл бұрын

Check to see if battery poles are on tight

@marleyfire3211 2 жыл бұрын

Why does it keep doing this

@christopherhayles2393 3 жыл бұрын

I like your videos but you didn’t show us you took the parts out. Next time show all details plz thxs

@emrecnar80 2 жыл бұрын

Any big problem, if we dont fix it ??

@svca12218 2 жыл бұрын

In my case, these codes made the vehicle go into limp mode (safe mode). You can turn off and on. It will go away for a few minutes; but then it would come back.