PLEASE SUPPORT THE CHANNEL FOLLOW @ITSSAMMALSEED (INSTAGRAM) ADD @SAM.MALSEED (SNAPCHAT) NEW VIDEOS WEEKLY! STAY TUNED! THANKS FOR WATCHING!
Пікірлер: 35
@joncotn Жыл бұрын
Thanks for the video Sam
@ai_12 Жыл бұрын
Thanks for the video, hello from Odesa (UA)
@MrDjayalex3 жыл бұрын
Hey @sam. When you removed the intake manifold was the starter motor easily accessible? I've got a starter issue and need to prep the car for the starter arriving tomorrow.
@MrSpeedkg3 жыл бұрын
Is much more easy if u completly remove strut bar, coz is few bolts more and much more space also for engine bay and small bolts use some hand tools not akku
@MechatronikMr3 жыл бұрын
Sam,Is it not true that these (efficient) flaps cause a smoother stalling of the engine while saving the dual mass wheel? And do efficient flaps affect acceleration in the low RPM range ??? M87 2.0d M47
@MrAbartlett3 жыл бұрын
What's the pipercross filter like on the car?
@savoostojic6513 жыл бұрын
Thank you for this video. One question: If I make same thing will I have to remove or change something on computer with OBD?
@Classic_Re-creation3 жыл бұрын
No need for any software mods or updates the computer will still tell the actuator to open and close and it will operate as normal just without the flaps in place
@zycienacodzien Жыл бұрын
why you didnt clean it inside?
@ALPINA5273 жыл бұрын
How many miles had your car done before you did the swirl flap delete? I have a BMW Alpina D3 saloon M47 engine.
@sammalseed87643 жыл бұрын
it had done just under 150,000 miles mate
@Classic_Re-creation3 жыл бұрын
Mine has just done 160k and removed mine a few weeks ago no sighn of damage on mine but when I went to un do the tiny t5 screw on each flap the screw shattered so it wS proberbly ready for going
@djkosmo87853 жыл бұрын
Why is this required and which are the consequences? Doesn't this affects the engine warm up process or the power this delivers?
@Classic_Re-creation3 жыл бұрын
If you don't remove the swirl flaps they can fail and fall into your intake and destroy your engine, the down side is that low end torqu can be lost due to fuel and air not mixing as well, real world driving their is no differance
@simonaarekol33362 жыл бұрын
Swirl flaps are only made to reduce emissions at idle running. There won't be any difference in power output. If anything, the power output will increase if you have bad swirl flaps.
@absaly Жыл бұрын
sterling job
@B2KJFF2 жыл бұрын
I have a 2007 bmw e90 with m47 engine. I have 2 questions 1) Do I need to do any coding after this? 2) do I need 22mm or 33mm swirl flap?
@Bondak4042 жыл бұрын
Dont need to code it after you remove them. I don't know about wich zise you need.
@iman27302 жыл бұрын
22mm
@kat01973 жыл бұрын
WTF you show everything but you didn't show how car run after delete FLAPS!!!! Come on!!!!!!!!!!!!!!!!!!!!!!
@dj.mabro.2 жыл бұрын
How many Nm torque for the bolts,please sir.Thanks
@zeznutbosanac53963 жыл бұрын
how many milimeters are those swirl flaps? 33 or 22? thank you
@Classic_Re-creation3 жыл бұрын
22mm on 2ltr diesel and 33mm on 3ltr diesel the flaps are bigger on 3ltr as the intake holes are bigger and their fore needs a bigger hole to allow the flap to go through
@Jonathanbaker3 жыл бұрын
map or O2
@maucina124 ай бұрын
Is there a way to find out if they were already removed by previous owners?
@leonhughes27614 ай бұрын
Yes pull.it off 😂😂
@TopoIl12 Жыл бұрын
What diameter should I get for the blanks,22mm or 33mm? I've got a BMW e90 320d m47 2006 163 ps
@jarnoverhoeven8773 Жыл бұрын
did you ever get the answer to that iam wondering the same thing
@TopoIl12 Жыл бұрын
@@jarnoverhoeven8773 yes bro, I've done the job with 22mm.
@jarnoverhoeven8773 Жыл бұрын
@@TopoIl12 thanks mate
@TopoIl12 Жыл бұрын
@@jarnoverhoeven8773 no problem bro,just make sure you have the same engine ,i had it done by a mechanic btw i didn't do it myself 👍
@jarnoverhoeven8773 Жыл бұрын
@@TopoIl12 i have the exact same engine mine is a 2007 but pre lci same horses and i already have had the manifold off for new plugs so shouldnt be an issue
@Cypry4hiphop3 жыл бұрын
omg. you removed so many unnecesarry parts. this is a 30 min job :)
@simonaarekol33362 жыл бұрын
care to elaborate? i can understand the EGR, but what else?