Table Saw Maintenance Tips

Рет қаралды 32,382

3 жыл бұрын

The heart of most woodshops is the table saw, but it could use a little care once in a while. This video will go over the main areas of care to keep your table saw clean and rust-free, plus how to maintain the mechanisms for smooth, accurate use.
Get a free, step-by-step article to give your Table Saw a Tune-up here: www.woodsmithplans.com/plan/t...
Download tips and tricks to make your cast iron table saw top look great and last a long time here: www.woodsmithplans.com/plan/t...
Subscribe to Woodsmith to receive tips, plans, projects, and techniques both in print, and in video. It’s all at www.woodsmith.com.
Follow us at / woodsmithmagazine
www.woodsmith.com

Пікірлер: 18

@chalcedony6858 3 жыл бұрын

I liked watching this. Not too many people get down underneath. I'd like to see more details of worm gear and so on?

@WoodsmithShowandmagazine 3 жыл бұрын

Absolutely. It's a little hard to get in there to see the inner workings of the table saw with a video camera, but you can download a free article on the subject with more photos here: www.woodsmithplans.com/plan/table-saw-tune-up/

@atillaserdar8988 Жыл бұрын

thank you

@terry2346 3 жыл бұрын

I set the blade to be parallel to my miter slot and this was VERY fiddly and took several tries but I could not believe what a difference that made! I also upgraded the belt and this helped having my old Craftsman 113.XXXX to be running like new. Keeping the ability to do a 45 degree tilt to the blade is much more problematic for me and I have pretty much given up on doing this and use jigs to get that 45 angle cut.

@jerrys576 3 жыл бұрын

Good chamfer bit in the router table does a better job.

@musicbymark 3 жыл бұрын

Where do you buy the flat referencing disk/dummy blade?

@williamwild1 3 жыл бұрын

I little maintenance or have a hook for a hand... Can i have a few minutes to think it over?

@larrywiltse6268 3 жыл бұрын

An option to the brass brush is your tooth brush that you should have replaced three year ago? Great video. I like your method of checking that the mitre slot is parallel to the blade. I have a Shopsmith and use a digital angle gauge to set the table to 90 degrees to the blade.

@WoodsmithShowandmagazine 3 жыл бұрын

Thanks! Glad you found the video helpful.

@musicbymark 3 жыл бұрын

Wish you'd show the table adjustment underneath.

@robbiehepler 3 жыл бұрын

Your framing square must be more accurate than most. I use a plastic drafting triangle clamped to my miter gauge. Very accurate.

@strrchristmas 3 жыл бұрын

I'm a long-time subscriber to both your KZfaq channel and your magazine. I really enjoy the videos. I have one problem: When you promise something, you need to deliver on that promise. When you say there will be links in the description, there should be links in the description. I followed both the published links, and neither took me to the items used in the video.

@WoodsmithShowandmagazine 3 жыл бұрын

Yep, that was my bad - I was a little quick on the Publish button. Thanks for pointing that out. I've added links to the accompanying material for this video now and also below. Let me know if you have any questions. Get a free, step-by-step article to give your Table Saw a Tune-up here: www.woodsmithplans.com/plan/table-saw-tune-up/?apid=36564 Download tips and tricks to make your cast iron table saw top look great and last a long time here: www.woodsmithplans.com/plan/table-saw-makeover/?apid=36564