TACOMA 3RZ MISFIRE | MY NEW TRUCK

Рет қаралды 9,376

2 жыл бұрын

New VIDEOS everyday.
Shop Merc- nuttynu.creator-spring.com
My vlog camera : amzn.to/34wKcMR
My PRO camera : amzn.to/3fAvQ4A
Pro Camera I use too : amzn.to/2R59ApU
My GoPro : amzn.to/3hZxL4e
Camera Gimbals : amzn.to/2ROJFU1
Ronn-M I love : amzn.to/34wpTiH
Drone: amzn.to/3vBoWkR
Camera Bag: amzn.to/3p6WLIs
Rode Mic I use: amzn.to/3fznIRK
Mic Recorder I use: amzn.to/3fVQ9bv
Portable LED lights: amzn.to/3c1iV9u
Join me on Robinhood, use my code join.robinhood.com/nux3
Business Inquires only | NuttyNumedia@gmail.com
Instagram @NuttyNu & @NuttyNu_4x4
Support the channel
Donate - CashApp- @ $NuttyNu
PayPal- @ Nuttynumedia@gmail.com
Disclosure: Links contain affiliates. When you buy through one of our links we will receive a commission. This is at no cost to you. Thank you for supporting NuttyNu and allowing us to continue to bring you valuable content.
Copyright 2011-2021
NuttyNu Media
No re-production/ re-upload of any content footage without written consent from me.
The story, all names, characters and incidents portrayed in this production are fictitious. Any similarity to actual person, living or dead, is purely coincidental.
No identification with actual persons, places, buildings and products is intended or should be inferred.

Пікірлер: 38

@moneydog6317 2 жыл бұрын

I had a theory it would be them injectors. This is just a thought when you're changing your spark plugs it doesn't hurt to put a little bit of anti seize on the threads for the future.

@SolarMillUSA Жыл бұрын

Reduce the torque value when using anti-seize, typically about 25% less, because it's lubricating the threads and the FSM torque values are specified for dry threads. Failure to account for this can strip the threads because more force is being applied than realized.

@Dwayne7834 2 жыл бұрын

Good score on the truck. Hopefully the injectors get you going.

@RippSnortin 2 жыл бұрын

Good info.

@REELCOMPAS 2 жыл бұрын

Thanks for sharing. I have the same issue on a 1995 Tacoma 4x4 I just picked up a few days ago. Mine turns on but misfires on all 4 cylinders. Still haven't narrowed it down. Keep us updated

@NuttyNu 2 жыл бұрын

burnt valves, new head install

@pitchforkpeasant6219 Жыл бұрын

@@NuttyNu burnt valves on mine. One burnt intake valve on both cylinders 1&4. Got .008 between shims and cam lobes on intake side which is spec but .008 was thinnest gauge i had and couldnt get it under ANY of the exhaust valves. For some reason the valve “lash” shrinks instead of the typical grows like old school us domestics. So not getting valve lash checked and properly shimmed will wreck your valves and maybe head too

@damienbell3155 2 жыл бұрын

Fuel pumps don’t go out on Toyota’s lol. I know. Go with injectors. eBay.

@skidmark7845 8 ай бұрын

Mine only has a random misfire at startup and will do this for about 30 seconds and then straightens up and runs smoothly all day even after several stops throughout the day. I got the truck after the owner did a butcher job changing the head gasket. He had it mistimed and it broke the timing chain. After replacing the chain and gear assembly, along with a new cover, oil pump and water pump. Replaced all the wires, plugs and repaired every pigtail and sensor (he broke everyone of them), I was able to troubleshoot the engine over heating problems to a broken vacuum line that was on a ported vacuum that controlled the eve. It was the initial cause of the engine over heating and they pulled the head off for no reason other than that. I had pulled the injectors off, put a 9 volt battery on them and sprayed carb and choke spray through them. This is where I went wrong by just not changing them. The truck has been running fine and never gave me any problems until now. I’m gonna change the injectors. I’m thinking that one of them is leaking down and the fuel pressure is leaking down after sitting a couple days. Being a common rail system, it makes sense that it throws a random misfire code. Only through the code once but if this is what’s happening, it doesn’t matter which injector is causing the problem. It’s gonna act up until it gets sufficient and even pressure on all four. At least I’m praying that’s gonna be the issue. It maybe time for a fuel pump also cause I’m also thinking that the internal check valve is leaking by. Either way, I’m gonna fix it even though it straitens out after a half a minute or so. I don’t know if the guy had the head resurfaced or if he had it torqued down right or not and I no way of knowing if he had it checked for cracks or burnt valves. Not even sure if the valve clearances were in spec. I’m gonna think it’s not that. I just had back surgery and don’t know if I’m up for that challenge

@skidmark7845 8 ай бұрын

Dam auto correct. I meant to control the EGR

@eugenegomez1 Жыл бұрын

do you have a video on removing fuel injectors on the 3rz? thanks

@NuttyNu Жыл бұрын

I don’t, but it’s really easy.

@chao9323 2 жыл бұрын

Do a compression test ..im a toyota tech 3rz motor are known for burnt valves

@NuttyNu 2 жыл бұрын

Okay!

@CatChase957 2 жыл бұрын

I was thinking the same thing, its possible to be the fuel delivery, but I feel like that would cause the misfire always instead @ low RPMs.

@bigfootswatching9986 2 жыл бұрын

I"m a KZfaq Tec.........try to search and google the issues here on YT.

@pitchforkpeasant6219 Жыл бұрын

Mine burnt 2 intake valves. 1 on cyls 1&4. Less than .008 on all exhaust valves. Was the thinnest had at the time. .008 on all intake valves strangely so in spec but still burnt 2. Future reference check valve lash every so often