Tacoma Supreme Suspensions 3" Front / 1" Rear Pro Billet Lift Kit (2005-2019) Review & Install

Рет қаралды 151,054

5 жыл бұрын

Shop This Supreme Suspensions Pro Billet Lift Kit: terrain.jp/2BAOTak
Subscribe for Daily Toyota Tacoma Videos: bit.ly/2FtUeUw
Level out your Tacoma and increase your ground clearance for off-road or on road performance with this Supreme Suspensions 3-Inch Front & 1-Inch Rear Pro Billet Lift Kit. This will level out the rake that came factory on your truck, allow you to fit a larger wheel and tire, and give it a stronger stance without any drastic or permanent changes to your suspension or drivetrain. terrain.jp/2BAOTak
Item TT2122
MPN# TYTA05FK3010A
----------------------------------------------------------------
🎞Subscribe for Daily Toyota Tacoma Videos: bit.ly/2FtUeUw
Facebook: / extremeterraintacoma
Instagram: / extremeterraintacoma
ExtremeTerrain.com is your shop for the best in Toyota Tacoma aftermarket parts and accessories!
www.extremeterrain.com
#ToyotaTacoma #SupremeSuspensions #LiftKit

Пікірлер: 150

@ExtremeTerrainToyota 5 жыл бұрын

Shop This Supreme Suspensions Pro Billet Lift Kit: terrain.jp/2BAOTak Subscribe for Daily Toyota Tacoma Videos: bit.ly/2FtUeUw

@1-4gentsmithfilms27 3 жыл бұрын

Can you please give me the tire size and type of 33s how wide and what rim size

@squish998 3 жыл бұрын

What a perfect and professionally done video. Simplified an install that would have taken twice as long otherwise. Keep up the great work!

@eh2341 4 жыл бұрын

This is, without doubt, the most thorough, well shot, well lit video that I've seen about putting in a spacer lift kit. My Supreme kit came today (2"+1 1/2") and I will have this video handy during the install. Letting me know what tools I'd need was great. Actually showing the steps from side to side was excellent (most just say, "Do the same on the other side"). I have subscribed. Thanks for the good work.

@ExtremeTerrainToyota 4 жыл бұрын

Thanks for the love, Eric! -Zach

@oldguygamer 4 жыл бұрын

I’m loving these videos specific to Tacomas!! Keep up the great work!

@ExtremeTerrainToyota 4 жыл бұрын

Thanks for the love! We definitely will! -Zach

@rickymejia48 3 жыл бұрын

Awesome video

@meandmyRC99 13 күн бұрын

Nice thorough explanation, thanks!

@bigislandboi4614 5 жыл бұрын

Gr8 instructions on the installation 👍

@Arbyfig 3 жыл бұрын

Seems good, i’m getting my Tacoma later this year, and I am looking a levelling kit just because of the aesthetics of it in all honesty, and I intend to to use it as my daily, just gotta make sure to get a wheel size that does not rub is all

@yungmexican32 4 жыл бұрын

With all of these vids I was able to do a leveling kit on my truck, did a 2.5” front with diff drop and a 1” block on rear. Didn’t want to stress the suspension too much 3” too much on front. Thanks for these great vids!

@ExtremeTerrainToyota 4 жыл бұрын

Thanks for watching! We appreciate it! -Zach

@jasondexter8018 3 жыл бұрын

What kit did you use and what size tire's and wheels are you running. I looking for the same set up as you have.

@yungmexican32 3 жыл бұрын

Jason Dexter 1” block rear, 2.5” spacer front. Tires are 265/75/16 on stock Toyota rims man. But I actually removed the spacer and got beilsteins 5100 on front and got beilsteins 5160s rear, I just left the 1” block. The rides a lot smoother now, paid less than 800 for shocks just took it to get an alignment so around $900 out the door. I recommend this set up man.

@yungmexican32 2 жыл бұрын

@Jordan James no I replaced front shocks with adjustable I got a 2.75” lift front

@RyanBe 4 жыл бұрын

Well 6 1/2 hrs later with jacks and a jack stand it all went well together. Only had an issue with a poorly threaded castle nut on the lower steering knuckle.

@Mmvexxx 4 жыл бұрын

Any issues later down the line with these mods? I have a 19 pro voodoo blue and wanted to run 32s

@RezekAndgrace 2 жыл бұрын

10 out of 10!!! Great install video.

@ExtremeTerrainToyota 2 жыл бұрын

Thanks for watching, Rez! -Zach

@Mike-cu6gk Жыл бұрын

Great video. I’m new to all this, what is the purpose of the transfer drop and do you have to do it with a 2” leveling kit?

@tripaccino Жыл бұрын

Are you adding a bump stop extension as well ?

@aveself 2 жыл бұрын

I have heard of people needing after market upper control arms and possible alignments done after lifting. Is this common with this type of upgrade?

@rickymejia48 3 жыл бұрын

Hi there Joe I've a 20 Tacoma 4x4 and thinking about installing a lift kit from ready lift SKU 69-5112 which is 3F' 1R' How difficult is to install the kit ? Overall do you think that I need to buy the loan plate spacer for the driver side please let me know thanks

@romandominguez8737 3 жыл бұрын

Will this work with the TRD pro Fox suspension?

@juancontreras3783 3 жыл бұрын

I did a similar set up3in lift spacers Front w/2.75 bilstein 5100 total5.75 front lift. My upper control arm hits coil spring. Do I need to replace upper control arm or go with a different set up?

@kylehamilton1120 2 жыл бұрын

What does the front spacer measure out to be? And also do you know the measurements from center of hub to bottom of the fender?

@YellowCab76 4 жыл бұрын

will this fit trd sport?

@richardglynn3744 4 жыл бұрын

Did mine today and used this video every step of the way so thank you very much! Very simple step by step, only thing I would say and this may just be in my experience, facing difficulty getting my tirerod out and refusing to beat it with a hammer I was able to still do everything with it being in place so in the end just one less extra step! Other than that thanks again!

@ExtremeTerrainToyota 4 жыл бұрын

Thanks for watching, Richard! We appreciate it! -Zach

@timfrancis6774 4 жыл бұрын

Are those wheels new painted ones? have a 13 with chrome wheels want black

@patuncangco8953 4 жыл бұрын

What if you have king coil overs?

@sammyfb488 3 жыл бұрын

Surprised they don't provide some type of tapered spacer so it seats better between the transfer case arms and the frame

@threadoflife 3 жыл бұрын

What are your thoughts on the Pro Comp Nitro 3” front leveling kit, 1” rear? 2021 Tacoma TRD Sport 4X4? This is what the installer for Toyota is recommending here with 285/70/17 33’s Nitto RidgeGrapplers on 17inch Matte black D694 Fuel Coverts -12 offset? Thoughts anyone please help. Quoted at $3,100.00 cash includes alignment, warrantied, wheel speed sensor calibration, diff drop, and adaptive cruise control calibration.

@chrismanlawe2528 7 ай бұрын

Is there any need to torque the nuts and bolts to spec? Or is it ok to just let the impact driver to go crazy?

@jesuscortes9982 3 жыл бұрын

I can only put the 3 ”leveling kit in front because I don't want to change anything in the back. Thank you for your answer.

@ArbitraryLifestyle 2 жыл бұрын

Your front will be 1.25" higher than the back if you do this. If you want to simple level it out, everyone uses a 2" lift in the front.

@kevinwatters8631 4 жыл бұрын

You kept saying transfer case, didn't you mean differential drop spacers?

@joefahey9642 5 жыл бұрын

I've seen a few videos of people using red lock tight on some of the strut bolts, is it recommended or does it not play a big factor in those nuts ever coming loose?

@jmataban 5 жыл бұрын

I would use it just to be safe since them nuts do come loose. better safe than sorry

@ignaciocarrillo9509 4 ай бұрын

what tire size is the 33? can you please give me the exact tire size 🙏🏻 , i have the same lift but i want to install 33s and i want to go with what you said fit well with minimum rubbing please thank you

@estarlymendoza1670 2 жыл бұрын

I like your job man

@ExtremeTerrainToyota 2 жыл бұрын

Thanks for watching! -Zach

@richardglynn3744 4 жыл бұрын

Question for ya, I put my lift on about two weeks ago 3” f 2”r, I’ve noticed that my leaf springs have become rather straight instead of having the curvature to it, is this normal? Is this something I should be concerned about? Perhaps drop to an 1” spacer in the rear?

@jprpaintingandrenovations6803 4 жыл бұрын

Sorry to bother you but I am about to install the same lift 3’f and 2’r, did you solve the problem and also did you have to replace the brake lines at front and rear ?

@Naut1188 2 жыл бұрын

Doing this mod on Friday, I hope everything goes smoothly.

@ExtremeTerrainToyota 2 жыл бұрын

Good luck on the install, Sean! We appreciate you watching! -Zach

@Naut1188 2 жыл бұрын

Everything went well. I'd suggest hitting all bolts and nuts with PB blaster as soon as you get the wheels off.

@goatifiy-8814 4 жыл бұрын

What’s the Tacoma completely stocked before you put it on or you had struts or something that you already had to put up there ??

@ArbitraryLifestyle 2 жыл бұрын

It was stock. Those are factory shocks and springs on it.

@gregoryc9087 2 жыл бұрын

What rims?

@Thirty-OughtSick 5 жыл бұрын

What about a kit that keeps the rake?

@joeholmberg250 5 жыл бұрын

How is the ride quality? The prices on this kit is nice, but want to make sure it's good quality. Also, you didn't need a torque wrench?

@ExtremeTerrainToyota 5 жыл бұрын

Ride quality won't change dramatically, but do expect things to stiffen up slightly due to the changed geometry angles. No torque wrench was pictured in this install but it is recommended that all major components are torqued back down to spec. Thanks for watching!

@brettmartin8460 4 жыл бұрын

When you say that 31” tires fit this lift, is that 265/70R16 or 265/75R16?

@greendrill12 4 жыл бұрын

Just type those dimensions into google and it’ll tell you

@rnb0234 3 жыл бұрын

I have a 2019 4x4 tundra crewmax I want to do the same setup what you recommend?

@ArbitraryLifestyle 2 жыл бұрын

Same kit, but for your truck year and model.

@panagiotisf7228 3 жыл бұрын

If I do 2inch spacer upfront and a 2 inch block rear will that keep my factory rake

@ArbitraryLifestyle 2 жыл бұрын

Yep.

@JesusQuintero-fq9kz 5 жыл бұрын

What size wheels on this truk?

@yonatandiaz417 4 жыл бұрын

Hi I have a 2016 Tacoma and I put a 3inch leveling kit in the front of my truck and but a bigger tires 285/70/17. Now my problem is that my tire in the front hit my upper arm when I do a sharp turn. Should I add wheel Spacers or lift up the back a little ?

@KODxsnip3r 4 жыл бұрын

Yonatan Diaz wheel spacers should do the trick.

@karlosmoreno3821 3 жыл бұрын

What offset?

@hockeyfreak043 5 жыл бұрын

I would watch doing the spacer lift..seen the springs on the coil overs fail ..spacer lifts r cheap if u want to do it that way.

@stacksmasher 4 жыл бұрын

Fail on new trucks?

@bryank3058 3 жыл бұрын

Does this add any wear to specific parts?

@ArbitraryLifestyle 2 жыл бұрын

Yes, the shock and spring in particular simply because you are compressing them more. You likely won't notice it for years, but it definitely increases the wear factor.

@PlugNuster 5 жыл бұрын

Any vibrations from the 1 inch lift blocks? Degree shims needed?

@franklinmejia6379 4 жыл бұрын

They haver a certain direction. They might be staggered.

@ArbitraryLifestyle 2 жыл бұрын

You want to get tapered blocks. The shorter end of the block goes towards the front of the truck.

@adrian-ll4to 4 жыл бұрын

Will this kit fit the TRD off-road?

@ArbitraryLifestyle 2 жыл бұрын

Yes.

@GigawattGarage 5 жыл бұрын

I got 2” blocks with my 3” strut spacers will it be level? Or will the rear be higher?

@JanoyCresva777 5 жыл бұрын

Gigabyte1024 it will have a tiny bit of front rake but barely noticeable, with 3/1 the truck looks slightly nose up from certain angles

@andy14169 4 жыл бұрын

i just put a 2" on the front of my taco, and it is now higher in the front and i just ordered 1" blocks for the rear. its not a full on TN tilt by any means, but i can notice it. i measured the wheel to fender, and there is now 7.5 clearance in the front and only 6.5 in the rear. so, a true level (using blocks, new coil-overs behave a little different) for gen 3 tacos is 1 inch lower lift block to the rear than whatever you put on the front. if you look at the before/after in this vid, you can see that the front is a bit higher on this kit as well.

@josuealicea6402 5 жыл бұрын

I will need to alingment the wheels???

@ExtremeTerrainToyota 5 жыл бұрын

Any time you modify your suspension, we always recommend you have an alignment done. Thanks for watching! - Zach

@jorgefalotico7158 4 жыл бұрын

Does this work for the 2wd?

@imthebest7290 3 жыл бұрын

They have one for 2wd

@roydi5122 3 жыл бұрын

I got the same kit but I would like to know why it squeaks??

@imthebest7290 3 жыл бұрын

Did you find out?

@garrettslayman6455 4 жыл бұрын

Just bought this 3 in Supreme leveling kit it's measuring the inch-and-a-half is that the right what's the thickness on a 3-inch?

@ExtremeTerrainToyota 4 жыл бұрын

Sounds about right to be! You can always get in touch with Supreme Suspension directly if you want to double check, but strut spacers normally never are the same height as the lift given (if that makes sense). The spacer itself in combination with the rest of your front end suspension will give the truck lift, not just the spacer itself like what you'd see on solid-axle applications. -Zach

@ArbitraryLifestyle 2 жыл бұрын

Yes that's correct. The level of lift is roughly double the thickness of the spacer.

@karlcalara1140 4 жыл бұрын

Is it safe to go off roading with these things on?

@ArbitraryLifestyle 2 жыл бұрын

Yes, but don't get crazy. If you hear any loud pops or bangs make sure you inspect things before getting back on the road. Specifically look to see if the lower shock mount in the front is bent (most common, but not common at all).

@kevinle4749 2 жыл бұрын

Will this fit on a 2wd 2018 Tacoma trd sport?

@ArbitraryLifestyle 2 жыл бұрын

Yes. Same exact process.

@Glocktard 5 жыл бұрын

No comments about how the truck handled after the install?

@ultrahighquality5657 4 жыл бұрын

For good reason

@mateo4057 4 жыл бұрын

Can I put this exact lift on my 2WD 2017 Tacoma TRD Sport?

@terrancetatum7599 4 жыл бұрын

I installed a Supreme Suspensions 3/2 lift on my 2018 Tacoma 2WD Sport last year. I'm running 33" tires on 17 x 9" wheels with a - 12 offset. Rides great, looks great, no rubbing, no scrubbing and no trimming. I'm completely happy with it.

@brandonwalston405 4 жыл бұрын

Terrance Tatum did you need the transfer case spacers?

@jprpaintingandrenovations6803 4 жыл бұрын

Terrance Tatum I have the same truck and I just bought the same lift, I got a question for you, do you have to replace the brake lines or something else ? Thanks for your help !

@ArbitraryLifestyle 2 жыл бұрын

Yes.

@rafaelbanderas101 3 жыл бұрын

Does the transfer case drop have to be done on a 2wd??

@ChrisTripp 3 жыл бұрын

2wd doesn't have a transfer case lol

@rafaelbanderas101 3 жыл бұрын

@@ChrisTripp lol I got a trd 4x4 premium now so I was a noob with a 2wd basic sr5 back then 😂😂

@papabear007 3 жыл бұрын

Why 3/1 vs 3/2 or just 2 inch in front

@nicagutierrez4441 2 жыл бұрын

3-1 will be level front to back 3-2 will still have a small rake to it 2 inch will be level to the back without adding anything to the rear so its still will be level just not as high as the other two otions

@johncart100 3 жыл бұрын

Is there a front transfer case on a 2 weel drive

@jackcarpenter1615 5 жыл бұрын

Does anyone know why this won’t fit on a 2wd??

@vitocorleone3724 5 жыл бұрын

Jack Carpenter It should fit if the particular 2wd tacoma you are referring to is a pre-runner, but the regular 2wd drive tacoma (5 lug wheel hub) has a completely different suspension design.

@adiaz0103 5 жыл бұрын

It will but the 2WD does not need the diff drop spacers that's why this video (and kit) is supposed to be for 4WD only

@vinnaaay4533 3 жыл бұрын

anyone know why you can't run them on a 2wd tacoma?

@user-xc2tk8wz2v 3 жыл бұрын

You can but the differential drop wouldn't be necessary on a 2wd.

@vinnaaay4533 3 жыл бұрын

@@user-xc2tk8wz2v thanks for the reply, I ended up running this lift kit and didn’t use the diff drop like you said 👍

@techtraveler1365 4 жыл бұрын

You forgot put all torque wrench requirements! When I change struts, all a parts I always have to put all torque wrench were put in factory tight bots.

@Xcrmat123 4 жыл бұрын

I was wondering about that...

@theravedaddy 3 жыл бұрын

Hes using an ugga-dugga gun. 15 ugga-duggas is the industry standard setting.

@huntermaki2892 4 жыл бұрын

Would this work on a Colorado?

@ExtremeTerrainToyota 4 жыл бұрын

This lift kit is made specifically for 2005-2020 Tacomas, I'd recommend looking into a kit made for your specific truck to ensure proper fitment. -Zach

@huntermaki2892 4 жыл бұрын

Extreme Terrain Toyota what lift/level would you recommend for a Colorado similar to this one

@graphguy 5 жыл бұрын

cost?

@dawsonedge7333 5 жыл бұрын

About $165

@ns671fr 5 жыл бұрын

youre supposed to actually change your UCA's at this lift height.

@ArbitraryLifestyle 2 жыл бұрын

New upper control arms would be ideal, as would a differential spacer and (if you have the OR model) the spacers for the skid plate.

@brandonwalston405 4 жыл бұрын

Do I need the transfer case spacers with 2wd?

@xSling 4 жыл бұрын

No you do not, you don't have a transfer case in a 2WD

@jonathanluevano4328 4 жыл бұрын

Safety glasses, protect your eyes fellas! Lol

@athaothao2880 3 жыл бұрын

tacoma supreme suspensions front ok

@jec2606 5 жыл бұрын

What’s the actual size of the coil spacer ? It says 3in but got mine and it’s 1” 3/4 .....

@ExtremeTerrainToyota 5 жыл бұрын

With how the front suspension is set up on these trucks, the spacer itself is not going to equal the height it provides. I would double check all of the part numbers on the box you received to make sure it is the right kit, and if everything matches you're good to go! -Zach

@shakennotstirred3607 4 жыл бұрын

Now you have vibration's like crazy! You have to shim the rear end!! Take drive line angle measurements before!!!

@garydp9760 4 жыл бұрын

So, what's the fix?

@stacksmasher 4 жыл бұрын

@@garydp9760 its a simple shim.

@ArbitraryLifestyle 2 жыл бұрын

There are kits with tapered rear lift blocks that solve this.

@Screaminbeamin 4 жыл бұрын

How is it a 3" in the front, those spacers definitely aren't 3"

@ExtremeTerrainToyota 4 жыл бұрын

IFS strut spacers are a little different compared to traditional coil spring spacers. The height of the spacer itself is never going to match the advertised lift height like you're saying. But the spacer itself *gives the lift height to the vehicles* with the help of the other suspension components. This will lift your truck 3" just fine. 😁 -Zach

@jeremyharris6635 3 жыл бұрын

You roughly adding 1.75ish inch on top the strut that at the mid point of the LCA so that 1.75ish inch at the mid point of the LCA moves the end approximately 3in.

@adg1017 5 жыл бұрын

Great video, but it looks terrible. It already looks like the back is lower than the front, so I imagine it’ll be dragging @$$ every time it leaves a stoplight. You have to have some rake, ppl. Even if you don’t ever use the bed you’re suppose to use (ya know, since it’s a truck).

@briancarpenter6413 5 жыл бұрын

what do you have then? And what would you recommend?

@adg1017 5 жыл бұрын

Brian Carpenter I have a 2/1 and it sits perfectly. Still has some factory rake, but it’s not as severe. I load my truck regularly and it never really drops below level. I can’t recall the brands I used, but it’s a 2” suspension lift in the front and 1” block at the back. The whole thing cost me $400 to have installed, including mounting and balancing the new Method wheels and Toyo ATII Open Country tires.

@prabhanjanlv 4 жыл бұрын

aaron garrett do you mind sharing some pictures?

@adg1017 4 жыл бұрын

Prabhanjan lv I’d be happy to, but I don’t know how on KZfaq

@prabhanjanlv 4 жыл бұрын

@@adg1017 Can you please add me from this link: youtu.be/addme/J0IoHRG8UXRgpVXrus_pSjYUCtKQKg

@RonaldAKline 4 жыл бұрын

The most important tool was left out... SAFETY GLASSES.. where were they..

@theravedaddy 3 жыл бұрын

Always 1 safety nazi on every video.

@JerryD770 4 жыл бұрын

Nothing is better then a bodylift you mess with suspension have alignement tire wear problems with driveline issues..

@garydp9760 4 жыл бұрын

and . . . ?

@leemccready845 3 жыл бұрын

Not once did you wear safety glasses or gloves!!

@theravedaddy 3 жыл бұрын

The video was very informative but that repetitive background bleeping noise forced me to go out the back and strangle next doors ginger cat. ....they got 3 more.... in case you use that music in the next video.

@TheUnseenSoldier 4 жыл бұрын

I’m confused, the guy in the video keeps talking about a strut assembly, but I don’t see one😏 As a strut is an integral component of a suspension, meaning it is a part that integrates all working parts of a suspension into one. A strut is a part that combines the duties of an upper control arm, a steering knuckle, a coil, and shock into one assembled part. A coilover does not do that, a coilover only performs the duties of a coil and shock. And a coilover has been what has been used in Tacoma’s since they were first introduced to the market in the mid 90’s. As with most other present day IFS light duty trucks, they utilize a coil over, rather than a strut to spring and shock dampen. A strut is a component that is more commonly found in cars, and crossover SUV’s. Sorry for the book, anyway, besides that tidbit of misinformation, the video was very informative.

@ExtremeTerrainToyota 4 жыл бұрын

I'll try to get the correct terminology passed along to the guys. 😉 Thanks for watching. -Zach

@TheUnseenSoldier 4 жыл бұрын

ExtremeTerrain Tacoma I’m just teasing 😉 great video, thanks for putting this info out there👌

@msilver382 4 жыл бұрын

Extreme terrain is a hustle. They sell you product, when it doesn't arrive they claim they can only refund a "store credit" even though you paid with a credit card. Real Truck and Rough Country have served me much better.