Homemade Rifle Primer

Рет қаралды 996,121

Tacome1942

12 жыл бұрын

this is not meant to be tutorial or anything like that. it just shows what works the best for me and how you use this information is all up to you.
it's very tricky to get the right cups, sometimes you get lucky, sometimes not. on a good run, i could get 5-10 cups in 5 minutes but on the other hand, i might only get 1-2 so i guess you'll get better over time. the primers i made take very strong spring and large mass(firing pin) to set off so for lighter firing mechanism, you might want to go with softer materials like aluminum. if your gun can set of real primers, then you can skip all this and buy the real thing.
THIS IS FOR LOW PRESSURE ROUNDS ONLY!!!!! (or percussion guns)
So again, just be very carful with her, she is very sensitive and have fun but stay safe!

Пікірлер: 394

@forge20 2 жыл бұрын

I watched this 9 years ago... and it's still good today. Honestly, I miss you, dude. Your craftsmanship, calm explanations, and cool projects were YT gold.

@anthonyatienza3363 Жыл бұрын

There's more people starting to get into this hobby now.

@VasilyTerkin228 6 күн бұрын

@@anthonyatienza3363 на это есть веские причины

@fifthcolumn388 3 жыл бұрын

If you don’t have the metal sheeting, just reuse the old primer cap by using a piece of metal rod (the blunt end of a drill bit) which fits inside the cap to punch out the dimple from the previous firing, then finish the way this video says to.

@tonyharris3759 7 жыл бұрын

Keep on Keeping on, You getting there, just make sure You take all of the safety precausions ..

@ChucksSEADnDEAD 11 жыл бұрын

Depends on the kind of primer. Some can be knocked out with a small rod inserted trough the mouth of the casing. If you can't, you can drill it out.

@bolshoibooze8010 3 жыл бұрын

I've tried this before back in 2012 ammo shortages...and it is not safe for semi operation. The compound is too shock sensitive causing 4/10 rounds I made had slam fire out of AR and SKS. But should work fairly well with single loader shotgun and bolt action.

@adam_-adam 9 жыл бұрын

do you know if a 50 bmg primer has more lead styphnate (explosive compound) that a 209 shot shell primer? i was wanting to make a mini shape charge with the primer' i do know shotshell primers are pretty powerfull and if you set it on a penny and blow it up with a blow torch the explosive will actually bend the penny" its amazingly strong for the amount of explosive compound in them" anyways hope you may know the answer' i wanna go out and buy some soon" also do you know anything about if rim fire shells carry more explosive compound than shotshell primers? i remember along time ago taking apart nail gun bullets and there was this yellow primer in it that ichave know clue what it was but there was a crap load' maybe more than the about of 4-5 shotshell primers.

@independentthinker8930 5 жыл бұрын

Under a real round with the pressures involved, will aluminum hold without a ruture? Pressurd should create a gas seal without glue, maybe nail polish to moisture proof it if the aluminun holds up. I would use the old cups again, flattening the firing pin dent would be much easier and it's steel.

@IDGAF56852 3 жыл бұрын

Great idea bloke,if theres no primers at all we improvise and this is how its done. Ive seen this method with matches and striker and works just a well but your ingredients are more stable and safer to work with. Good stuff 👍👌

@samuelpatrick5050 11 жыл бұрын

thats a berdan primed shell. to remove just fill it pretty close to the top with water, find a punch the size of the bullet bore, put the primer over a hole, and hammer the punch down

@discoverytravels7426 Жыл бұрын

😂😂😂😂

@JETHO321 3 ай бұрын

@@discoverytravels7426 Whats funny?

@colingallagher4848 3 жыл бұрын

Great video, for those doing this, just make sure to test test test until you are sure what you do works.

@kellyshea92 6 жыл бұрын

I would never have thought that cap gun caps would be strong enough to use as the explosive to ignite the powder

@evanharrison4054 3 жыл бұрын

Any impact sensitive material is good, basically. If you grind matchheads and mix it with ground dust from the side of the matchbox and put it in the primer...it will corrode the shit out of your barrel, but it works.

@joneifer8987 3 жыл бұрын

Best primer video I could find. Thanks for showing us how. I feel totally less stressed about running out of primers now.

@NareshKumar-ui7lr 3 жыл бұрын

00ⁿ0ⁿ00{po 0}ⁿ9pp}}

@B3RS3RK3RAH 3 жыл бұрын

@@NareshKumar-ui7lr indians be like:

@jerrytrimble691 3 жыл бұрын

The Afghans used chopped celluloid film as powder and strike any where mach heads in the primer pocket to reload rounds.

@andrewlambert7246 2 жыл бұрын

Use a needle to get them out. One can use the old cup by straitning it out a little. I will do a program sometime in the future and show how to real primer compound from the grounds up. One can also make primer compound for .22 ammo as well.

@Game-oe8ts 9 жыл бұрын

Pretty cool. Thanks.

@TheSkater1233 11 жыл бұрын

where do you get the measurements for the guns you build

@dlighted8861 3 жыл бұрын

Is there a way to just use the plastic caps? I can't find paper caps locally and don't buy online.

@xProxywarsx 11 жыл бұрын

It's very fun as well as helps you save your rounds and not shoot 50 at a time. It also stops his gun from getting too dirty. In addition to what is typed, a light load is ideal for his bullets as his springs are meant for light strikes.

@FrostyyShooter 11 жыл бұрын

what type of caps do you use cause the one i bought the powder is glued to the paper

@Mohammed.AltamashKhan Ай бұрын

Thank you brother for the knowledge 🎉❤😊

@FrostyyShooter 11 жыл бұрын

when i try to make a primer the drill bit will tares the metal apart any ideas to prevent that?

@UnSengorX 11 жыл бұрын

would you trust in these to use a real load? (i mean gun power and a proyecftile)

@billybutcher9912 3 жыл бұрын

Using spent primer cups aside, this is the most dependable method of building a primer. Dependable, as in useful and functional. Other methods yield less reliable results. Great video.!! (I heard you just fine.btw)

@cal30m1 3 жыл бұрын

Why not use a flat drift punch to flatten a spent primer’s cup?

@jung6423 10 жыл бұрын

Would you tell me what that tape at 3:21 is? I want to know about that tape.

@chapiit08 11 жыл бұрын

Homemade brass can be made out of solid bar stock on a lathe. Then it needs to be annealed and formed over a press and die(s) It's the only viable method that doesn't make use of press punches, drawing presses, etc. It would be wise to stick to a straight case caliber like 45-70 etc. with a very slight taper that can actually be machined to final shape/dimension rather than press formed and a Berdan primer pocket is ideal as they are much easier to make than the Boxer type.

@kumbackquatsta 11 жыл бұрын

could you do a video on making metallic cartridges without using fired brass

@fordosember 5 жыл бұрын

Perfect work.

@rideride5696 3 жыл бұрын

looks like your homemade primer got pierced during the test fire, would be interesting to see a fully reloaded round fired

@rogerraven6976 3 жыл бұрын

Yes this is a problem

@Sahkopekka200 9 жыл бұрын

Nice rifle, stan!

@dalroache 4 жыл бұрын

Due to its small size etc won't it be blasted out back end I know it not have no where to go but won't gases escape out back etc I don't know as I from the UK so I am not knowledgeable like you guys but hey awesome man I love the fact most things can be done with a little bit of determination and a little bit of knowledge etc

@preese43 3 жыл бұрын

Seems more efficient just to buy the primers already made. What is time worth?

@samuelpatrick5050 11 жыл бұрын

not sure if its already been covered but could i use aluminm can metal for this or no?

@shishKababGamers666 11 жыл бұрын

what caliber rounds are you using? i found a spent shell (7.62) but the flash hole is split into two little holes so i cant remove the primer :(

@erickcouvrette1385 2 жыл бұрын

Hi, What is the thickness of the sheet metal you used ? Have a nice day.

@brandonm4107 10 жыл бұрын

good video but is this safe for real bullets wouldedt you be risking some serious blow back with the improvised cup

@lucasoldaker2158 3 жыл бұрын

What kinda stock is that gun on or what is it wrapped with

@Jagdtyger2A 8 ай бұрын

Very cool, I am sad that my eyes no longer an srr small things like that to do it my self any more. But very cool. All that is needed now is a tool like the "tap cap" percussion cap former

@Moriuz95 11 жыл бұрын

How did you get the old/used primer out?? I tried to hammer on it from the other side so it comes off but it dosen't :/

@silverballer1911 11 жыл бұрын

how can i stop my cups getting cut?? when i push it in the metal splits at the bottom

@Marine052191 11 жыл бұрын

Silverballer1911, you using a knife to press the compound in the primer cup? How are the getting cut?

@ansuz444 4 жыл бұрын

"Take her out, you'll wanna be gentle with her, she's very sensitive, she'll tend to go off on you if you mistreat her. Then, tap her out."

@bermudezhg 3 жыл бұрын

If you took the anvil from an used primer, you can reuse the primer cup as well !! Just hammer flat the old firing pin indentation. This method works 3 or 4 times with a given used primer cup.

@branni6538 2 жыл бұрын

It will work more if heated to red hot and flattened then quenched or left unquenched. Heating removes the stress in the metal and so will normalizing it.

@crazychickensss 7 жыл бұрын

your the man . thanks !

@ademirberlofa8669 2 жыл бұрын

you fire in the aluminium?

@jubeetobbe5025 8 жыл бұрын

What was the powder you use?

@OspreyKnight 11 жыл бұрын

If you're making a straight walled case like a 38 special you're fine and easy. But drawing out a brass case you need someone to machine a series of forms(that are accurate to thousandth of an inch) and get a heavy press.

@lisalisa3635 2 ай бұрын

You could use Paper to contain the charge, Bullet and primer like the flintlock rifles of the 1700s

@jacqueslefave4296 3 жыл бұрын

Be sure to scrub and oil that barrel, and to be safe, the receiver too, the cap powder/material may have corrosive residue, don't wait, do immediately after the shooting session! I can smell sulphur from those popped caps, that's a warning sign!

@YourMomsLover 11 жыл бұрын

Since you have used primers, try pulling the anvil out, using the drill-bit to tap out the firing pin mark in the orig cup, and do the same, just reload the primers...

@gereekt 11 жыл бұрын

how do you take the original primers out of it?

@CDel86 7 жыл бұрын

My god, reloading takes long enough as is. Hell of a SHTF method though!

@DobleWhiteAndStabley 3 жыл бұрын

Look up the base components of priming compound and their history. Pressing cups is not that hard to mindlessly punch out a few hundred. Recycle your anvils or make them. Then use your highschool chemistry knowledge to make it. (Be mindful of your local laws)

@donaldcampbell5277 3 жыл бұрын

A muzzleloader would be faster.

@DobleWhiteAndStabley 3 жыл бұрын

Well yes but actually no. Dude, you're not going to be doing this in the heat of a fight or hunting or practice. You do it on your off time so that you save time between shots when you actually take them. I'm thinking you aren't very experienced with guns yet. There are a lot of people like that this year and that is ok.

@SammyNeverEver 3 жыл бұрын

@@DobleWhiteAndStabley how do you make anvils?

@SwordTune 3 жыл бұрын

@@SammyNeverEver They're just pieces of metal that won't budge so the primer can be crushed. The more important thing is to know how to make the primer compound.

@user-ij2es9kz1q 3 жыл бұрын

That’s an impressive paper rifle.

@yourfriend3999 3 ай бұрын

bro how did you get the 556 cartridge i need answer please?😂

@ferdiandimatgaper2017 2 жыл бұрын

Wow... good experiment... good job...

@user-oz2mk3po7c 3 жыл бұрын

What is the material of sheet metal? How thick?

@終わりのない愛 2 жыл бұрын

Be careful not to kill us once🙄

@tusharsonawane5664 5 жыл бұрын

What is the name of that red round stick

@victorb22622 2 жыл бұрын

Nice video.thought i m new about bullet and weapon, i just curious, how he shot without gun powder in bullet.it has just a primer.but primer for what ? Without gunpowder it has no use.lol.see,i firstly told i m new

@zou-w 3 жыл бұрын

What is the red paper called？

@Micscience 2 жыл бұрын

Was that shot just the force of the primer or was there gun powder inside as well?

@AustralianKickboxer1 11 жыл бұрын

@Tacome1942 Can you please show us your method for getting old primers out?

@tiger5gaming 11 жыл бұрын

I'm not really a gun person so I don't really know a lot of stuff about guns, but what does the anvil do?

@TheAngler2210 11 жыл бұрын

what was that metal sheet from? i didnt understood :P

@samuelpatrick5050 11 жыл бұрын

so i can use this on Tula ammo?

@OspreyKnight 11 жыл бұрын

If you're using a boxer primed case you just stick something though the touch hole and push it out(he's using a boxer primed case) If you're using a berdan primed case... look up on youtube how to remove it. Berdan primed cases have two holes in the base of the case, while a boxer has one large one. The advantage of a berdan case here is that you don't need that triangular anvil because the case is the anvil.

@jaybeebee14 11 жыл бұрын

@cornzplosion Well then that wouldnt be metallic now would it?

@conangaming2156 3 жыл бұрын

This proves that gun/ammo restrictions don’t work, they can’t get rid of either. Good video mate, this technique could be useful in the future if our governments keep making restrictions

@bensamule3252 2 жыл бұрын

yah they cannot take away guns but they can ammo so we just have to make it

@ajaxashford4815 7 жыл бұрын

can any of you learn the basics of what he is trying to show you? paper gun or no. learning the basics for how to make a primer or to take a spent cartrage and turn it back into a round you can use again for hunting or self defense is PRICELESS.

@jizzmonkey9679 4 жыл бұрын

Not exactly priceless when they are commonly available rounds,

@albertforletta1498 4 жыл бұрын

I’ll give you $28.89. Go buy 1,000 primers. It’s faster, and easier. Lol. Cheers.

@RobCalhounPGH 3 жыл бұрын

@@albertforletta1498 & @ jizzmonkey Funny how those comments aged like a fine milk. The current situation is exactly what this was intended for, not being a cheap ass.

@albertforletta1498 3 жыл бұрын

Rob Calhoun , would you want me to give you $28.89?? Lol. I don’t need to make my own primers. I will never experience an ammo shortage. You could shut down all ammo manufacturers on this entire planet and reloading suppliers, and I will still be going to the range shooting lots of ammo for the next 5 years. What ammo shortage? I didn’t know we had an ammo shortage.

@RobCalhounPGH 3 жыл бұрын

@@albertforletta1498 Nope, can't shoot money. But some ammo would be nice :)

@CinamonChina 2 жыл бұрын

how would you homemade "Anvil"? If you wana try

@andregross7420 11 жыл бұрын

Have you ever had a cap blow up on you while making the primer?

@mo-sg3tg Жыл бұрын

What is the red paper??

@Avalonious 11 жыл бұрын

Homemade gun: Check! Homemade bullets: Check! Homemade primers: Check! Now to make homemade brass!

@alonsoflight 11 жыл бұрын

how you take out the old primer of the cartridge

@fa1rcz902 3 жыл бұрын

1 question how did u put that newspapers on that rifle so prefect?

@starshiphopper7044 2 ай бұрын

Cause rifle is made of newspaper

@126mx 11 жыл бұрын

this is gona be a very useful talent in the near future if this ammo shortage bullshit continues or guns get outlawed

@thechuckennoris5751 3 жыл бұрын

This aged well

@lupacchinobros 3 жыл бұрын

Yep...this guy right here is a damn hero.

@culebrasty 3 жыл бұрын

@@lupacchinobros 😂

@darrionj707 2 жыл бұрын

Oof

@vaghelamayur5876 3 жыл бұрын

Bhai tumne praimr ke lastme kya dala

@skymycat1 Жыл бұрын

I think you have come up with a great why of reloading primer s

@johnnymccann5607 3 жыл бұрын

How constant are they.

@billucf96 3 жыл бұрын

excellent use of easy to get materials...reloading process can definitely be made quicker though

@ashashaikh4317 5 жыл бұрын

How you made the paper rifle

@shoiabrigana 3 жыл бұрын

Just use match heads tho and grind some of where you scratch the match head to powder and mix them , to try it that it will work put a little bit on your left thumb nail and put your right thumb nail where the powder on and scratch it quick and it’ll spark that mean it’s ready to go or beat it with hammer becareful the mix is sensitive to force.

@marzuki7389 Жыл бұрын

By Y

@amanameen4564 3 жыл бұрын

can i use craker only not paper

@chocolateninja22 11 жыл бұрын

I bet it's fun when the roll cap goes off while cutting it

@prancingdog 8 жыл бұрын

*REQUEST:* Please use a microphone, it is so hard to hear what you are saying sometimes. Love the videos.

@nknatewood8226 8 жыл бұрын

Agreed. *YES*, Tacome Mumbler, please do use a mic!

@radenhamzah8038 Жыл бұрын

@@nknatewood8226 mintakdikirim kipnya

@nknatewood8226 Жыл бұрын

@@radenhamzah8038 : Don't speak whatever this is - an "Indian/Indonesian" dialect? Universal English, please. TIA!

@schl0tte 11 жыл бұрын

the falling hammer squeezes the primer to the anvil

@rosquetamarclesterr.6477 3 жыл бұрын

I want to know how to make a improvise primer plss

@OspreyKnight 11 жыл бұрын

If you have berdan primed cases yes because the anvil is part of the case. if you have boxer, like he has you need that anvil or there will be nothing for the primer compound to be smashed against.

@ythiecinh8536 3 жыл бұрын

Which matal to do cup primmer

@danlocoelho 11 жыл бұрын

can someone tell me how to take the original primers off the rounds? I tried a lot of stuff but it is still there, seems like its glued ¬¬. Sorry for any wrong word im from brazil ;)