No video
Tamiya TT02 97MPH Speed Run PB - And then 85mph Crash into my foot!
Рет қаралды 12,354
Күн бұрынMy Tamiya TT02 had a great day and a new PB running the Surpass Hobby 5900kv motor.
LINKS FOR THE PARTS I USED IN THE BUILD AND THE TOOLS I USE BELOW👇
Motor 3650 Surpass 5900kv 👉amzn.to/3cES182 & Here amzn.to/3t8CpAa
Motor & 120 Amp esc 👉amzn.to/3pD1ujO
Surpass 3650 5900kv amzn.to/3t8CpAa
Tamiya aluminum drive shaft/prof shaft joints for TT02 amzn.to/35OtFVx
Arrma Blx185 esc alnk.to/87Sj9IW
Porsche 962 200mm Body By Delta Plastik
deltaplastikus...
Integy double fan amzn.to/3sz50Ow
High Speed Gear Set(adaptor) TAM54500 OP-1500 amzn.to/35Mz0gd
Yeah Racing adjustable TT02 Motor Mount TT02-013BU alnk.to/aeQXScE
www.rcmart.com...
Tamiya TT02 Aluminum rear Upright 2.5 degrees Op-1549 TAM54549
amzn.to/3oNtAsK
Contact Foam Tires 26mm alnk.to/6mIii87
Tamiya On-Road tuned hard spring set Op-440 Tam53440 alnk.to/4MttsWR
Batteries 100C 4s Spektrum 3200mah & Peak Power Plant 3s 45C
Spektrum alnk.to/g33YfgU
Gens Ace TT02 4s Battery alnk.to/goTucWa
Gens Ace 3s alnk.to/2Qp8Ga2
Gears
Spur gear Robinson Racing 48 pitch 52 Tooth Associate/Hpi Touring car
alnk.to/ehUoreK
Pinion Gear Robinson Racing 48p 45 tooth
Tamiya TT02 Low friction suspension balls Part # Op-1559 Tam54559
amzn.to/2LEbues
Clamp style aluminum wheel hub Part# Op-570 Tam53570
www.rcmart.com...
GPM aluminum driveshafts amzn.to/3rOu7eU
GPM Racing Steel differential gears Part# TT2100-BK amzn.to/3suKEWF
Tamiya TT02 Aluminum Steering Set amzn.to/39DDHtZ
BEST low cost Radio transmitters with longest range
RadioLink RC6GS V2 Radio here:👉amzn.to/3cFplf7
Dumborc X4 Radio Here 👉amzn.to/3u91p9O
RC Car Speed GPS here: 👉bit.ly/2PHiVDk and here alnk.to/dpl2mdU
Chargers Here 👉alnk.to/bEbsIa8
Low Cost Good Charger 👉amzn.to/2PO9JNk
Batteries Here 👉alnk.to/2FuOwMJ
Spektrum Smart Charger & 3s smart battery bundle 👉alnk.to/dAfNwln
Spektrum Smart Charger & two 4s smart batteries bundle 👉alnk.to/b7rbLWv
Spektrum Smart Charger & two 6s smart batteries bundle 👉alnk.to/cwLfDtu
Tools I Use HERE:
Hex drivers. Good quality & tight fit: amzn.to/3m88iWl
Soldering iron amzn.to/3BYxdSD
Solder: amzn.to/31ExE4y
Pencil torch: amzn.to/3djYyUS
Velcro: amzn.to/3sL9MZ2
Double Sided Tape Heavy Duty amzn.to/3bQVbV4
Motors & Esc's
Hobbywing 👉
Castle Creations 👉alnk.to/gVEbZ2v
Spektrum Firma 130amp Esc and Motor combo 👉alnk.to/7qdh0L3
Cheap Good Quality Motor & Esc Combo's
1/10 scale
3650 4300KV motor and Esc combo amzn.to/36lbEi1
1/8 scale
3660 Brushless motor & Esc Combo amzn.to/3qnXasq
3670 Brushless Motor, 120amp Esc Combo amzn.to/3fzxV0W
Cheap Good Quality Brushless Motors
1/10 scale
3650 5900kv amzn.to/2LVF9j4
3660 3800kv amzn.to/3qseAku
1/8 scale
3670 2850kv amzn.to/3sx99Tb
3674 2250kv amzn.to/39ESlRv
Cheap Good Quality Esc's
60amp Esc amzn.to/3D06I0b
80amp Esc amzn.to/3dsDviP
120amp Gool RC amzn.to/3o0rzZe
Crawler motor & esc good quality HERE amzn.to/304J6cP
Camera and mount HERE:
GoPro Hero 8 that I use: amzn.to/31CuP4g
Camera/Phone mount for your RC transmitter:amzn.to/3md0oej & here amzn.to/3rE2SU3
#Cheap fast RC Car
#GoolRC
#TT02
#Tamiya
RC Car Crash
Tamiya TT02RR
Tamiya TT02D
Tamiya TT02
Tamiya Speed Run
RC Speed Runs
Arrma Speed Run
Traxxas Speed Run
Surpass Brushless Motor
RC Charlance 60a ESC
Tamiya LIPO
Tamiya Jumping
@KaizerTest 3 жыл бұрын
Hi guys...it's amazing what the little TT02 can accomplish with a cheap brushless motor! Thanks for watching and subscribe and like if you can I appreciate it very much. I answer all comments so if you have any questions ask away. 😄
@R53.charlie 3 жыл бұрын
When you gonna run it again mate?😂😂 gotta get to 100!
@KaizerTest 3 жыл бұрын
@@R53.charlie Sometime this year I think...lol. I haven't been out speed running at all this year yet. We are still in lockdown and the cops have the right to question you. $750 ticket! 😢 But I want to run my Slash 4x4 first. So far 132mph...I need to get to 150 with it. Probably I will run the TT02 then. I was also thinking a TT02B speed run car would be cool too.
@R53.charlie 3 жыл бұрын
@@KaizerTest oh, didn’t realise you were still in lockdown!! That’s shit😒 my tt02 is now more stable, and I’m guessing it’s going about 70mph considering my rustler does 60mph🤔
@KaizerTest 3 жыл бұрын
@@R53.charlie Yeah Canada is not doing great with covid. 4500 cases a day for my province of Ontario. Schools are closed and on remote earning. So my only options right now are my street and the park next to my house...lol. I can't even get any wood to fix my ramp. 70mph on the TT02 is awesome bro. Keep pushing. I have a big 4s battery I may try out. It's heavy but it may give the car more traction and less voltage sag at full throttle. Robinson Racing spur gears are sold out everywhere too and I'm down to only a few so I hope I don't munch any spur gears...lol.
@R53.charlie 3 жыл бұрын
@@KaizerTest haha, I’m only running 24/64 gearing, running my 2 nimhs in series, the esc gets hotter than the motor does! The motor actually stays fairly cool, I can still touch it, and the max I’ve had it at was 65 degrees celcius, so it’s not too bad, but the esc get to about 75, that’s a bit too hot, but I’m gonna think about adding more fans under there or something😂😂 I only run it on my series nimh setup now, because my rustler gets hotter, and it’s rated for 4s!😂 and that only pulls 100a! Funny how it works🤷🏼♂️
@IowaBudgetRCBashers 11 ай бұрын
97 mph on a car that barely does 20 out of the box. So awesome!!’
@StewMac570 4 жыл бұрын
Great video!! Awesome editing. Sorry about the crash, it’s never great when that happens But your very close! Keep at it. I have lost count the amount of times I crashed. Some nice big winglets on the side of the body will help with some stability. Distance is key. Even if you need to take the RC to the start point with you car and set it up then drive back to you driving position. Then a nice progressive pull on the throttle. I ran lockers in both diffs for 100% traction. 800 weight oil in the shocks. Also heavy duty servo saver or horn. Best of luck and I’m keen to see you crack that 100.
@KaizerTest 4 жыл бұрын
Hey thanks Stew! I wouldn't have made it this far without you. Yeah it was a bittersweet victory with this PB. Right there with 97mph only 3mph from 100...then disaster...lol. Oh well...I'm still pleased and shes back together but I had to use regular TT02 front upper A-arms(hope they run ok). I did put thicker diff oil in the rear but the front has light oil...I guess I need to address those issues and thicker shock oil as you said. The winglets are a good idea that I forgot about and will see if I can find something to make some with. I have been running my TT02B on 3s with bigger tires offroad and I snapped a front axle and trying to source stronger axles now....hahaha. It never ends😂👍 Thanks for watching brother.
@kevindigit 4 жыл бұрын
Squeeze slowly into your throttle thru, I’ve learned things from you as well and wanted to say thanks for the content, I’m setting up a GT2 ve now with 6s in parallel so taking it easy with a fast car out the gate, keep your head up, better days ahead
@KaizerTest 4 жыл бұрын
Thanks brother. I have been trying to squeeze slowly and ease into top speed. I have basically two spots to do speed runs. This spot and a rural spot. I like this road better because it's wider and has curbs...the other spot is narrower and the farmer nearby has been getting dirt from his tractor onto the road plus it's a lot further away. The issue with my close spot is that it's not long enough to ease up to speed. I was only 5-10 feet from going into the intersection at the end...lol. I have my son using binoculars to help me see the car and get it turned around as well.
@UDRC85 4 жыл бұрын
Great run bro. Congrats on the new pb. My first car was the Tamiya TA-05.
@KaizerTest 4 жыл бұрын
Thanks brother. My dream is to make 100mph with a Tamiya...its been done before but I got my first Tamiya in 1983 so breaking 100 with one would be sweet. Its doing better than my Slash...lol.
@UDRC85 4 жыл бұрын
Kaizer Test what editing software do you use if you done mind me asking.
@honestbloke2427 4 жыл бұрын
Great video 👍
@KaizerTest 4 жыл бұрын
Thanks man.
@RCSpeedRunDubai 4 жыл бұрын
Grats with the new PB. I just started running 1/10 aswell it is harder to control compare to 1/8. What helps me is a gyro, turned it to 5% enough to keep the car straight. Good luck for future runs!
@KaizerTest 4 жыл бұрын
Thanks for the congrats brother. I do have a gyro on it set low....helps a bit for sure. The car seemed to be running on rails last year. This year (and after some crashes) it seems more squirrely....lol. Oh well, she is rebuilt and ready for action again...or disaster...hahaha.
@RCSpeedRunDubai 4 жыл бұрын
@@KaizerTest great winglet might solve it aswell ;) thats the fun of this hobby ;) gotta love that speedrun adrenaline
@TheRCMaster 4 жыл бұрын
That's insane bro 😳🤣 I hope your foot is ok? Awesome speed btw and sick video 👌
@KaizerTest 4 жыл бұрын
Thanks brother 🤜🤛 yeah the foot was fine. I actually was wearing high top sneakers and other than the hard blow it did nothing to my foot. The car is fixed now too. 😀
@MZBallistic 4 жыл бұрын
I've been looking for a 10th scale car and don't want a 4tec, this may be it. One thing always in the back of my mind is the car hitting me. I'm gonna try standing on the sidewalk from now on. Be safe! subbed.
@KaizerTest 4 жыл бұрын
Yeah I have a 4tec as well and havent touched it since I bought it. The great thing about the TT02 is parts are cheap and fairly plentiful. I have a second kit I'm using for parts and you can usually get the parts tree you need faily easy. I just run a cheap motor and Arrma esc. Tires are BSR or Contact foams and they last. I'm still on the first set of foams...lol.
@Addicted_2RC 3 жыл бұрын
Ok even though you lost it that takes serious control to keep that planted at those speeds. Impressive. So that definitely looked like it hurt!! I love how you step onto the street to tell the fire truck to wait. 🤣😂🤣😂🤣😂🤣👍👍👍👍🔔🔔🔔
@KaizerTest 3 жыл бұрын
Thanks brother. 😃 You can see the car was pretty twitchy. On the 97Mph run when I started off it went pretty close to the curb. This car got sidelined as I started to take more interest in my Slash 4x4 because that car will eventually do 150mph. I'm probably going to take some time again in the spring and take another stab at 100mph with this TT02. I'm going to try using some softer shore tires for more traction and see if that helps. I also have another motor that may push it over 100.
@Addicted_2RC 3 жыл бұрын
@@KaizerTest your really making me want to pull the slash out and rip it apart to turn it into a speed run car 🤔🤔🤔🤔 awesome run can’t wait to see break 100 mph with this
@KaizerTest 3 жыл бұрын
@@Addicted_2RC Thanks bro. Yeah the Slash is going to 150mph. I'm either putting in a Castle 1717 or TP 4070 2200kv motor. And then going to gear it up more. I have some GRP's I'm going to try and 18mph more to 150 😃 Is your Slash a low center of gravity Slash or a high center of gravity slash? I mean the chassis.
@Vassilika1 2 жыл бұрын
5:02 same here... first Love was the Hornet back in the 1980's many other Tamiya RC cars to follow. ;-)
@cheapspeedrc9100 4 жыл бұрын
Do you have a set-up stand? It has made a world of difference to how my TT02 tracks. It’s also a little confidence booster knowing that everything is pointing in the right direction. 100mph is an elusive target (speaking from experience), but you’ll get there. Keep flying the TT02 flag.
@KaizerTest 4 жыл бұрын
No setup stand.. I eyeball everything...I know..not good...lol. My 97Mph run was straight. It's is a little squirrley until it gets to like 60 and then it seems to lock in on a straight line. I love TT02's on the street. I find my TT02B to need a lot of upgrades to make it be able to handle any kind of power. I wish I had a few fellow TT02 speed run or any speed run enthusiasts here in North Toronto I could do runs with. I'm all alone...lol.
@uprcoutlaws2417 4 жыл бұрын
Oh man I know the feeling! I was hit by a gopro during our XO-1 speed runs. GREAT VIDEOS!
@KaizerTest 4 жыл бұрын
Thanks brother! Yeah these speed runs can be super dangerous...you never know if the car is going to come at you. I have an X0-01 as well that I will be running soon on the channel too. Thanks for watching. 👊😀
@RCACTIONAUSTRALIA 4 жыл бұрын
Wow It’s Fast! Hopefully the Ankle is ok 👌🏻
@KaizerTest 4 жыл бұрын
Lol...yeah I'm fine...luckily I was wearing high top running shoes otherwise it may have shattered my ankle.
@JesseBMotors 4 жыл бұрын
Glad you’re alright. That thing is fast 👍🏁
@KaizerTest 4 жыл бұрын
Thanks brother. I'm glad I wore my high top sneakers that day...lol.
@angryyank 4 жыл бұрын
Damn thats pretty fast for sure..... I feel your pain I once airborned my RCIO worlds car into a small bump on the street and it flew into my leg and broke my tibia.... I converted it from a buggy into a land speed record car and on that run it was going about 76 mph and that was way back in 1995 & it was then ranked the fourth fastest RC car in the country..... Was kiinda amazing when these high speeds was pretty unheard of... The all metal chassis is a bone breaker if it clips you at high speed... I learned on that run to rebuild it with a bigger wing and a bit stiffer rear shock setup
@KaizerTest 4 жыл бұрын
Damn! Thats crazy! I got off easy I know. It could have been disasterous. And 76Mph in 1995 was fast! I like the way you say way back in 1995...lol. It doesnt seem like long ago but it is now..😥😂
@angryyank 4 жыл бұрын
@@KaizerTest That it is for sure hope you get her fixed up and rippin in no time.... Thanks for the subbing too
@BigChuck_1 4 жыл бұрын
Just got my first TT02 kit. I know I’m a long long way from 85mph. But.... Who knows. Great Video.
@KaizerTest 4 жыл бұрын
Hey Chuck thanks for watching and commenting. Get the Tamiya high speed spur gear set, a set of Contact foam tires in a harder compound, some rear aluminum uprights for 2 degrees of rear toe in, and run a little toe out. Then you want an 80-120amp esc and a 5900kv motor. Also get the Yeah racing adjustable aluminum motor mount and run robinson racing 52 spur and 45 tooth pinion. All that will get you to 80 plus mph. Add a DeltaPlastiks 2mm Porsche GT body and you are set to about 100mph. I missed 100mph by 3mph...and am bummed I couldnt just put it to rest...hahaha. I may try again for 100 this month but I'm so busy...and I'm bashing RC's offroad when I get the chance too. If you need any tips on the TT02 feel free to ask. I bought my Robinson gears from Amain hobbies online and my esc and motors from Amazon and Ebay. I subbed your channel bro...I like your vids.
@DefiantAML 3 жыл бұрын
Thats why they call em "ankle breakers"
@KaizerTest 3 жыл бұрын
😂
@HRM.H 4 жыл бұрын
Also might want to run more thick differential oil or use yeah racing solid axles.
@KaizerTest 4 жыл бұрын
Yeah for sure. I learned that the hard way on my Slash 4x4...lol. This one I have thick diff fluid in the rear and it helps a lot.
@99headcase 3 жыл бұрын
Yup 100 in a TT o2 good stuff. That's also what I noticed with tamiya! As soon as you're running good (crash) and fix ...
@KaizerTest 3 жыл бұрын
Thanks brother. 👊😀 3 mph shy of 100 but I was running into a headwind. This season I should be able to crack that 100mph in this car. My Slash has done 132mph so far but I need this one to 100mph.😀
@littleskyrcchannel4044 4 жыл бұрын
Was the injury okay? Thank you for commenting on my video as well ❗️
@KaizerTest 4 жыл бұрын
Oh yeah I was fine. Not even a bruise because I was wearing high top running shoes that had lots of ankle padding..thank God...lol.
@littleskyrcchannel4044 4 жыл бұрын
That's right, there is no injury ❗️
@shaneellasdaicastrestorati3675 2 жыл бұрын
Well done that's what I was just thinking of trying to do " world's fastest tamiya. Did you get to 100
@KaizerTest 2 жыл бұрын
Well for world fastest Tamiya check out Stew Mac on youtube. 97mph was my best on this car. I got my Slash 4x4Gt to 138mph. After the 97mph run I havent run the Tamiya.
@c.k.hobbyshop3351 Жыл бұрын
What battery were u running when u hit 97 mph 3s or 4s ? Just wondering 🤔 great passes to bad about the damage
@KaizerTest 11 ай бұрын
4s Spektrum
@713Ace529 4 жыл бұрын
just subscribe. hi there. like that you making great memories with your boy. have fun even when you're struggling it makes it all fun and laughter. I'm looking to get a TT2 and build it for my son. he's thing is to go fast. I'm into nitro and crawlers but I enjoy going fast too.
@KaizerTest 4 жыл бұрын
Thanks for the sub...subbed back. If you get a TT02 get the TT02RR. It has a much better fluid filled differential and a bunch of aluminum parts most notably the rear uprights that give you 3 degrees of toe in. You need this for high speed stability.
@BriansRCStuff Жыл бұрын
Do you think this of the Kyosho Fazer MK2 is a better speed run car? Great speed runs! I know what that feels like as I hit my foot at around 60 mph and it wasn’t right for over a month!
@KaizerTest Жыл бұрын
Hahaha! Yeah for some reason I put high top sneakers on that day and they totally saved my ankle. Not sure what Kyosho you are speaking of but in my opinion if you want to do speed runs the easiest way to go fast is with an Arrma Limitless or Infraction.
@BriansRCStuff Жыл бұрын
@@KaizerTest Sorry, I missed an important word! The Kyosho Fazer MK2 platform. Oh, no doubt but I was trying to have an on road car that isn't crazy expensive that can still be made to go around 100 mph reliably. I have been maxing out my Bandit on the stock power system but I think I am getting close to what I can do with it (without upgrading to a 4s system) and was considering a dedicated on road car. Good move with the hi-tops! 😃
@KaizerTest Жыл бұрын
@@BriansRCStuff Yeah I'm not sure about the Kyosho fazer but if you can get the spur/pinion closer to 1:1 ratio you should be able to get it to 100mph with foam tires.
@kevindigit 4 жыл бұрын
🙁 but as long as you’re fine you can always get another RC hope all is well
@KaizerTest 4 жыл бұрын
Yeah I'm good brother...thanks for asking. I was wearing high tops and I literally felt perfect right after...Thank God I decided to wear my high tops.
@homeworkpictureshq 4 жыл бұрын
Thank you bro
@KaizerTest 4 жыл бұрын
No problem my RC brother. 😀🍺🍺
@Addicted_2RC 3 жыл бұрын
What an intro!!! How did that feel?!?!?!?
@KaizerTest 3 жыл бұрын
😂 Like somebody punched me in the ankle...lol. When I left home that morning I put my high top running shoes on for some reason. There was a lot of padding in the ankle area so basically nothing happened to me. Now if it was my Arrma Felony or Infraction it probably would have been worse. When it hit me I didn't stay planted I tumbled and did a side flip...hahaha.
@Addicted_2RC 3 жыл бұрын
@@KaizerTest you can kind of see the flip roll. 😂🤣😂🤣😂🤣😂🤣 At least you got some awesome footage!!! 👍👍👍👍👍👍👍👍
@KaizerTest 3 жыл бұрын
@@Addicted_2RC Thanks brother. I wish I had my son taking video with my cell phone to see me do the flip...lol.
@Addicted_2RC 3 жыл бұрын
@@KaizerTest That would’ve been epic!!!!!
@cwatson42785 3 жыл бұрын
Wow that was intense!!! 😯 I need to get a body like that when I plan to push high speeds! What is that body called? Also I appreciate you helping me out as while I'm not green to rc im very green to 1/10 scale touring cars lol. I had alot of fun building my first tamiya! My buddy Philthyco rc pushed me to getting one last winter and im glad I did! Can't wait to see you hit that triple digit mark!! So close!! Lol wow that hit was crazy. Lucky you didn't shatter your ankle!...WASTED! 🤣 That hit and fall was pretty epic!
@KaizerTest 3 жыл бұрын
Ahh your buddy is Philthyco...hes a good guy. And I dont mind helping. I have to say these 1/10 Tamiya TT02's are hard to go fast. The setup of steering is important and Im no expert. I just know toe out on the front and toe in on the rear and use foam tires. The body is important for sure. You need to cut the rear of the body out to let air escape otherwise pressure builds up and the body acts as a parachute. Did you see my Tamiya Top Force buggy? I did 71mph on my street on a crappy road. I was using softer foam tires. Only a few outings and they are gone.
@cwatson42785 3 жыл бұрын
@@KaizerTest Hahaha I was talking to Phithyco about you and was telling me about your top force buggy! Ill definitely check it out! Yeah I have those aluminum uprights. Guess the tt02r model comes stock with them along with a few other hop ups. Ill grab that body and foams when I gear up for sure 👍 I'll watch that top force run today for sure! Thanks again brotha! Cheers from the U.S!
@KaizerTest 3 жыл бұрын
And yeah that TT02 came at me like a missile. I wish I had another camera set up to capture the impact...lol. The body I used is a 1/10 DeltaPlastik Porche GT body. I have to look again exactly which one. If you look on DeltaPlastikusa.com website you can probably find it. I ordered directly from them. As for 100Mph in a Tamiya it may have to wait until next year. Im onto running my Slash 4x4 trying to break 125-130mph. And I have my Arrma, Infeaction, Limitless and Felony I want to build up. Eventually looking for 150mph if I can. But the Tamiya is still with me and I will hopefully crack 100mph with it.
@KaizerTest 3 жыл бұрын
@@cwatson42785 Cheers from Canada brother.👍🏼 What are you using for gears? You need the Tamiya high speed gear set..but basically just the adaptor that comes with it. Then you need RobinsonRacing touring car 48p spur in 52 tooth. And get RobinsonRacing 45 tooth pinion. Then you need to dremel out the gear cover for the pinion to clear. Need to cut it out and make it open. What motor and esc are you going to run?
@cwatson42785 3 жыл бұрын
@@KaizerTest Hey Kaizer I'm running a 25 or 26 Robinson pinion, stock spur and im running a hobbywing 3652 3300kv motor and max 10 80a esc. Once i can top this off by reaching top speed once i get tires that will actually allow me to not spin out at 3/4 throttle I'm gonna gear up for sure! Thanks for the gearing advice! I appreciate it! 👍👊🍻😎👌
@lowq6989 3 жыл бұрын
did you have to use a program card for this esc? Great run!
@KaizerTest 3 жыл бұрын
Thanks bro. No you don't need a program card for the Arrma BLX185 esc.
@rendeverance 4 жыл бұрын
Is that the 5900 surpass on 4s? What is your final drive ratio? (Or motor rpm needed for 97mph?) Thank you, planning to try for 100 soon with my tamiya too 👍 I hope the leg is better and the car repairable 👍
@KaizerTest 4 жыл бұрын
Yes the motor is a surpass 5900kv. My gearing was 45 pinion and 52 spur. Final drive is 3.00 roughly but I just experiment with gear combos. Yeah my foot was totally fine no injuries at all...lol. My high top shoes saved my ankle. Thanks for watching bro...post some vids of your progress.
@knightknightman1502 4 жыл бұрын
What shell is that your using please?
@KaizerTest 4 жыл бұрын
Its a DeltaPlastiks 22mm Porsche GT body. They ship all over the world. It's very stiff being 2mm.
@seancunningham1361 3 жыл бұрын
I have a carbon framed chassis tt01 and a 5200kv motor 60a esc and a 3s battery thing hella fast
@KaizerTest 3 жыл бұрын
Nice. These 1/10 scale cars are little screamers.
@seancunningham1361 3 жыл бұрын
Yup
@formosadowns 2 жыл бұрын
have you try test rc on desert highway in remote place very flat straight!
@KaizerTest 2 жыл бұрын
No desert near me in Canada but this road is good. I got my Slash 4x4 GT up to 138mph on this road. The trouble is keeping this car straight.
@CarlosDelaoGunEngraver Жыл бұрын
what camera and mount are you using?
@KaizerTest Жыл бұрын
You mean to video the run? At this point I was using a Gopro session 4 but then moved to a Gopro Hero 8 for better stabilization. I use the gopro head strap.
@Cultralight1 4 жыл бұрын
Damn! :-O
@conradloag7046 3 жыл бұрын
I work down the street
@KaizerTest 3 жыл бұрын
Nice! Do you have any Rc road cars or any Rc's? You can join me sometime but I usually go really early.
@TestDriverRC 11 ай бұрын
HOWS THE CAR?! 😮
@KaizerTest 11 ай бұрын
It's still intact. I haven't run it basically since this 97mph speed run.
@TheK20eg 3 жыл бұрын
Holy crap thank god your okay smh
@camaroboy383 4 жыл бұрын
Holy smokes man! That was crazy! How sore was the foot the next day? Ouch! But that 97mph pass was wicked!🔥🔥🔥💪..
@KaizerTest 4 жыл бұрын
Thanks brother! I was pissed she didn't hit 100mph. That was my dream to do my first 100mph with a Tamiya (I'm an old school Tamiya guy..Old fart now)lol. I was wearing high top shoes so other than getting knocked off my feet I was perfectly fine! hahaha.💪😅
@camaroboy383 4 жыл бұрын
@@KaizerTest I'm with ya man.. would love to see that thing hit 100.. 😎
@KaizerTest 4 жыл бұрын
@@camaroboy383 Thanks brother.👊😀
@seancunningham1361 3 жыл бұрын
What body do you have? Where can I get one? Thanks
@KaizerTest 3 жыл бұрын
It's a DeltaPlastik Porsche GT deltaplastikusa.com/collections/1-10th-rc-bodies/products/0408-porsche-962 Bought it there.
@seancunningham1361 3 жыл бұрын
Thank you!
@KaizerTest 3 жыл бұрын
@@seancunningham1361 No problem brother.
@All-rc804 Жыл бұрын
Hi what spur and pinion did you use for this run?
@KaizerTest Жыл бұрын
Been awhile but it's either a 52 or 48 spur and like a 47 pinion.
@user-os9vo7is7o 4 жыл бұрын
What electronic equipments and gears are used in the car in this video bro🤔
@KaizerTest 4 жыл бұрын
Hi brother. Well I have an Arrma Blx185 esc and a Surpass Hobby 5900kv motor. For a radio I'm running a Spektrum DX5C. Gearing was 45t Pinion and 52t Spur. The body is DeltaPlastik Porsche GT 2mm thick.
@user-os9vo7is7o 4 жыл бұрын
KaizerTest RC wow that‘s pretty great.i have sakura xis nu and i want to upgrade my car until it can run about 90-100mph.But I still have a long way to make it come ture😩😩😩
@HRM.H 4 жыл бұрын
Hahahaha ono rip tt-02 and rip foot. I just build my tt-02 type S. 13.5t blinky setup.
@KaizerTest 4 жыл бұрын
Lmao...I know it hit hard! I was wearing high top shoes and thank God it saved my ankle...the car not so much. I got her rebuilt already but had to use some stock TT02 parts. I don't want to dip into my Yeah racing stash just yet...I want to get to 100 on the cheap if I can.
@fredericwikaryjak3299 3 жыл бұрын
Hello from France 🙋 Good job !!! 👍👏 What IS that body? Sorry i'm bad in english 🙄
@KaizerTest 3 жыл бұрын
Hi from Canada! We have 2 official languages and French is one of them but I'm not good at it..so no worries on the English. You said it perfectly. 😃🍺🍺 The body is a DeltaPlastik Porsche GT. It's 2mm thick so it keeps its shape at high speed. Click here: deltaplastikusa.com/products/0408-porsche-962?variant=29064400437322
@fredericwikaryjak3299 3 жыл бұрын
@@KaizerTest Thanks you very much to answer me . I'm pressed to see your next record 👍. Je te souhaite une bonne continuation 🙋😀👍
@KaizerTest 3 жыл бұрын
@@fredericwikaryjak3299 Thank you very much my friend 😃🍺🍺 Once the snow melts here in Toronto I will be back at the speed runs. My Traxxas Slash 4x4 did 212Kph or 132Mph and my Arrma Felony with stock body did 119Mph. I can't wait to get back out there and go fast. Thanks for watching and post some video's of your cars if you get a chance. Cheers. 🍺🍺😃👍
@fredericwikaryjak3299 3 жыл бұрын
@@KaizerTest How much KV are you ? What sort of pinion and main spur gear for this speed ? TT02 max 23 T pinion ? I have a TT01 PMM and i 'm not very fast with my 3900KV and 25T pinion and 61t main Gear 😁 in 3S.
@fredericwikaryjak3299 3 жыл бұрын
Hello Est ce que le TT02 High speed Gear set peut se monter sur le TT01E ? TT02 High speed Gear set Can go to TT01E ? 🙋😁👍
@littleskyrcchannel4044 3 жыл бұрын
If I move this Tamiya tire at 100mph, will the tire burst? www.tamiya.com/japan/products/51049/index.html And which is stronger, hobbywing max6 or Arrma's esc in this video?
@KaizerTest 3 жыл бұрын
You need to run foam tires like Contact Foam's or BSR's. Those tires you showed will deform and balloon and come off the wheel at 100Mph. The Max 6 is definitely a stronger esc but it's too big for a 1/10 scale car and not needed. The Arrma Blx185 is strong enough.
@pyroman7191 4 жыл бұрын
I have a tt02 replica toyota tureno 8e86 and its for drifting
@KaizerTest 4 жыл бұрын
Sweet! I need to do a drift build TT02 someday.
@pyroman7191 4 жыл бұрын
If you look on my channel you can see it its quite fast with grip wheels but likes to flip if you turn it a cm when you are going 30mph
@KaizerTest 4 жыл бұрын
@@pyroman7191 Cool video. I like the way you and your Dad are running RC cars together...good family time.
@pyroman7191 4 жыл бұрын
@@KaizerTest thanks it is quite fun i have 2 more rc cars i have a off road buggy and a road buggy that looks like the boomarang and anotherone that looks like a boomarand but red and 1/5 scale 60mph but is restricted soo need to take that out and the ecu is blown and waiting for a copasitor/cant spell. That blew up and its has been a few weaks scince we baught them so we have to find another one somewere.
@KaizerTest 4 жыл бұрын
@@pyroman7191 Well keep at it. Half the fun for me is building and working on RC's. Good you are learning mechanics and electronics.👍🏼😀
@AmericanDefender 2 жыл бұрын
What body is that?
@KaizerTest 2 жыл бұрын
I have a link in the video description.
@CarlosDelaoGunEngraver Жыл бұрын
what body is that?
@KaizerTest Жыл бұрын
Deltaplastik Porche GT 2mm thick.
@uptownfragrance6148 3 жыл бұрын
u should get a wind mic bro
@KaizerTest 3 жыл бұрын
Yeah for real...lol. it was bad. I got a newer Go pro with stabilization and put a wind cover over the mic now. Almost no wind noise even in heavy wind now. Here's a newer vid and my fastest speed so far with my Slash. kzfaq.info/get/bejne/hKyDfcuV2teblYU.html
@uptownfragrance6148 3 жыл бұрын
the cross wind is making your car flip its always windy there
@KaizerTest 3 жыл бұрын
Yeah more than likely. Overall it's a good road. A little too short for my Slash 4x4 though. Are you running a TT-02?
@uptownfragrance6148 3 жыл бұрын
@@KaizerTest yea i looking to get one looks pretty good i enjoy your videos pretty detailed
@uptownfragrance6148 3 жыл бұрын
@@KaizerTest on pinion would u do a 43 spur 45
@KaizerTest 3 жыл бұрын
@@uptownfragrance6148 Did you see my TT-02 speed run car up close vid? kzfaq.info/get/bejne/bLB8gt2ksdPUooE.html
@KaizerTest 3 жыл бұрын
@@uptownfragrance6148 I ran a 45T pinion with a 52T spur for 97Mph. Maybe a 43T pinion would give me a little more torque to cut through the wind and go a little faster.
@justinsilva3790 4 жыл бұрын
Do you have links to the entire build?
@KaizerTest 4 жыл бұрын
No but I can help you with info..I don't mind helping. Ask as many questions here as you want.
@justinsilva3790 4 жыл бұрын
i have a servo and gyro id like to use i mainly just need a motor esc combo thatll work well as ive been just trying to research a motor that would work well w AWD. im pretty new to this its a blast tho! which motor and esc did you use exactly
@justinsilva3790 4 жыл бұрын
i saw it said surpass but what brand and stuff? and thanks for getting back to me
@KaizerTest 4 жыл бұрын
@@justinsilva3790 The gyro is ok. Not absolutely necessary and should only be used on a low setting otherwise it will go into a high speed rear end wobble. I used an Arrma BLX185 esc which is a bit overkill. A 120amp esc will take you to at least 90mph. I used an OCday which is pretty well a Gool RC. A hobbywing Max 10sct is 120amp NOT regular Max 10 which is weaker. This esc is basically what I used originally www.ebay.ca/itm/HOBBYFANS-120A-80A-60A-Brushless-2-4S-ESC-BEC-for-1-8-1-10-TRAXXAS-RC-Car-J0C5/254649105731?hash=item3b4a44fd43:g:r8kAAOSwv1JfBs~u And motor is this just choose 5900Kv one www.ebay.ca/itm/SURPASSHOBBY-3650-5900KV-5200KV-Brushless-Motor-Waterproof-Sensorless-Motor/124014990051?hash=item1cdfde92e3:g:hx0AAOSwyWFd-dYU
@KaizerTest 4 жыл бұрын
@@justinsilva3790 The Brand itself is Surpass. I bought from Amazon but it seems there is a shortage on Amazon right now probably because of Covid 19. Ebay has them but they are orange can now. It has to be a 3650 sized motor. Get the 5900kv one or 5200kv. Go to AmainHobbies.com For gears order Robinson racing 48p 45t pinion and a 52 tooth spur. Get at least 2-3 spurs in case you strip one. an extra pinion would be good too. Maybe get a 42 or 43 tooth. Maybe grab one 60t spur as well so you can play with ratios. But I used 45t pinion and 52 tooth spur so you can just stick to that. Grab some Contact racing 30mm Foam tires off Ebay. The stock body will take to to 80mph before you run into aerodynamic problems. Speed runs cars cut out the rear of the body around tail lights to let high pressure air to escape and prevent the car from "parachuting"..lol.
@andreasneophytou9125 3 жыл бұрын
what tires do you use in this car??
@KaizerTest 3 жыл бұрын
I use Contact foams 26mm 35 shore rating.
@daiciuapostol79 3 жыл бұрын
Your life it's on danger out there🤯 watch your kids🙏
@KaizerTest 3 жыл бұрын
Yes for sure. I always try to keep them back from the road.