Tannus Armour Tire Insert Installation

Рет қаралды 46,301

Күн бұрын

Пікірлер: 82

@jayarnold.244 4 күн бұрын

I used the same tire with the same tube and followed the instructions as provided. Took about an hour as I also put “ flat out” in tube as well. One point I highly recommend is to break the bead on both sides and to slightly inflate tube. The ride feels the same. Great video. Thank you.

@tjmmcd1 2 жыл бұрын

Just got a pair of Tannus inserts for my Hemiway Cruiser. The hardest, knuckle bruising part was aligning the innertube valve into the rim 'after' inserting the Tannus liner. Thanks so much for taking the time to post this, how-to video. Makes it so much easier than doing it blindly.

@flyingsoul7147 7 ай бұрын

Hey do u need to remove the wheel. My wheel is detached from the rim but i dont want to remove it toonkuch work 😂

@jamrockccccc 2 жыл бұрын

Thank you very much for your video sir , I was 2 minutes away from throwing away everything including the bike until I saw your video many thanks

@1purposedrivnlife Жыл бұрын

😂 haha!! Nice to know that I'm not the only one.

@FarmerFpv 3 жыл бұрын

Throwing the Tannus Armor into the Cloths dryer for 5 minutes straitens it out back to normal il also making it much more playable. You should try it trust me, makes it so much easier.

@RideTannus 2 жыл бұрын

That is a new one for us. I like it! We've always recommended some sunlight or a hair dryer. I guess just make sure the boss is ok with it before ya do it lol. Thanks for sharing!

@ryanrodriguez1234 16 күн бұрын

I'm already in too deep. Taking a break, been at it for about 45 minutes. 🫠

@frankcloskey7789 2 жыл бұрын

Excellent putting everything back together.8/26/2021

@twotwentyswift Жыл бұрын

This actually turned out to be even easier than it looked on KZfaq.....that's a first! 😂

@RideTannus Жыл бұрын

Love to hear it!

@stevedirdochegal6568 Жыл бұрын

Got my Tannus Armour today for my 29 x 2,60...i got a whole new set of Continental tires along with it..since it comes all bent up like that now after installing and taking it for a spin my wheels are bumpy af so im gonna ride it to and from work next week and if its still that bumpy im going tubeless.. probably shoulda listened to my gut feeling in the first place...

@krikri3387 3 жыл бұрын

Well done!

@redandblack124 2 жыл бұрын

awesome video!! Thanks

@michaelmarquina8365 Ай бұрын

From my experience working with Tannus Armour liners, you need to run smaller tubes. If not you'll have a heck of a hard time putting everything back together.

@michaelh2716 3 жыл бұрын

Thanks for the info!!!

@axelstandoutspeakswithmusi4220 Жыл бұрын

Thanks for posting.

@tpmdenji Жыл бұрын

Boy I hope it’s as easy as you made it look

@reggin_spelt_backwards 5 ай бұрын

I broke 4 fingers installing mine with a double down tire but its ok. I will heal and ride my bike after!! Cheers 🎉

@trevorabrahamfixesbikes8662 2 жыл бұрын

The instructions that came with my tire levers state that they are not for installing a tire. They should only be used for removing a tire from a rim or removing ears from under a flat brim hat.

@traviseller3770 Жыл бұрын

Yeah those metal tire levers are a great way to mess your wheel up If you use a little body English hold your tire down into the drop Center you can generally do this with a small plastic tire liver or do it by hand is a decent video but there are a lot of mistakes they would give people trouble

@tpmdenji Жыл бұрын

My milk carton also says it’s causes cancer

@shura_666_ 2 жыл бұрын

Thank you

@MR57LV 3 жыл бұрын

Very helpful

@californiabound9258 Жыл бұрын

I had a bike shop installed these on my Cyrusher 690 . I can't go up a hill anymore without killing myself peddling with assist on. Could the shop have done something to the motor? The Batterie is good. This could be just bad timing for the motor as well. I had Cyrusher check everything via video. The thought it was the controller so I replaced it. No change. Just looking for advice. Thanks

@SwoleKage 2 ай бұрын

I just got some yesterday, it was a super easy install. Only thing is, I've noticed tire pressure drops, is that normal or due to the material condensing under the weight of my bike? The tube is the correct size and is brand new so I'm not sure if I did something wrong

@MoyHobbies 2 ай бұрын

They suggest trimming it did you have to trim or just tuck the excess liner in the rim?

@davidrosa3182 3 жыл бұрын

According to tannus website you need a smaller tube. 26x3 tube for a 26x4 tire. You used the same one. I’m lost here

@Sup-jz2ow 2 жыл бұрын

He says on the vid tannus recommends a smaller tube but if you don't have one the normal one will work 4:50

@whyndellgrizzard7495 2 жыл бұрын

It came with them- but other youtube vid's continued with the 4"- after using the 3.5" it straightened out.

@whyndellgrizzard7495 3 жыл бұрын

I followed along with what you did- I have a RAD Rover step thru 1 with 4" tires. When I removed the tire deflated and removed tube, this was the front tire. Then inserted the TA, it seemed big for the tire but finally got it in, then inserted a new tube that was sent with the TA, aligned valve pushed everything in place, then reset tire. Set on floor roll it around with a little weight, then began to inflate tire, stopping at 10#'s to roll and massage it, then finished inflating. After inflating to 15#'s I noticed valve stem was sitting at an angle, so deflated, repeated procedure from installing tube and reinflation, making sure valve stem was straight, once again valve stem was set at an angle, after full inflation. QUESTION: WHAT COULD BE CAUSING THIS?

@ryanjspinks 2 жыл бұрын

Try inflating the tube on its own, valve stem may be crooked from the factory

@whyndellgrizzard7495 2 жыл бұрын

@@ryanjspinks Got it straightened out, when it inflated the tire twisted, this caused it to keep kicking the valve stem off to the side. So now I have developed a process by which I install and then inflate to avoid this in the future, I have the rear tire to do this weekend.

@kenneth7197 2 жыл бұрын

I installed my

@sdflyer1672 2 жыл бұрын

@@whyndellgrizzard7495 Thank you for the information! I had the exact same problem today while installing the front tire...I finally had to take everything apart and start from the beginning being extra cautious to make sure the valve stem didn't tilt to one side while tucking the tire bead back in. VERY time consuming and frustrating. So, can you please explain with more detail what your discovered process consists of? Thank you so very much in advance for your help! I'm doing the rear wheel tomorrow :(

@Alusnovalotus 2 жыл бұрын

Lol. I have the #2 and I still got a flat with these on. Now I can’t get the damn tire off and it’s frustrating as hell

@nedkent5239 2 жыл бұрын

Trying to get the hop out of Fat Bike tires has seriously made me consider getting rid of my Fat Bikes. Almost impossible on certain tire and tube combinations to get hop out! Have tried EVERYTHING

@syberphish 6 ай бұрын

... hop? What is this dreaded hop you speak of? It sounds terrible. I've no doubt that now that you've made me aware of it I'll become afflicted by it quite soon.

@syberphish 6 ай бұрын

what causes hop? My daughter is learning opposites in school and she'd tell you that the opposite of hop is not-hop, and if you think about it... she's right.

@MrKingcj33 2 жыл бұрын

Good information but why didn't you show the tuff part like how to seal the bead to the rim?

@RickDuarte-wh8dn 6 ай бұрын

I believe the procedure you mention is only for tubeless tires

@bobgeldoff9413 13 күн бұрын

i have a slime tape so if i got this Tannus Armour and used it too will this be enough so i dont have to buy more slime?

@Im1234and5 Ай бұрын

Can a 3.0 inner tube fit for a 20" 4.0 inner tube I mean 20" 4.0 rim.My rims is 20" 4.0.But will a 3.0 go into a 20" 4.0 ?

@slowmopoke 6 ай бұрын

Some people just like to do it in the rear

@colinwatkins2950 2 жыл бұрын

ive heard that tannus linner can deteriorate inside the tyre over time and mybe damage your inner tube.

@kengunnett2017 2 жыл бұрын

What if it does, you want to give up protection from flats over time, to save a $20 tube?

@RideTannus 2 жыл бұрын

A little bit of baby powder can help combat this. Creates a nice slip zone. If that is happening, it's most likely a tire defect? Cheers

@Zippy0George0Bungle 2 жыл бұрын

No matter how much I massage everything, I still can’t get shot of a bulge in the sidewall, it moves each time I inflate. Very frustrating.

@sitzwerke 3 жыл бұрын

Hi, thanks for instruction :) You have a 26 x 4.8 Wheel. What size is the Tannus Armour?

@johnathanrandells4325 2 жыл бұрын

Did u ever find out buddy

@RideTannus 2 жыл бұрын

@@johnathanrandells4325 The Tannus Armour would be our 26x4.0-4.8 insert. Here is a link if needed: tannusamerica.com/products/tannus-armour?variant=31871966216303

@osasosasosasosasosasosasos7313 Жыл бұрын

They have size for fatbike 26×4.9-4.8

@dannyhero2536 Жыл бұрын

What's the dimensions of the tube for this tire I can't find them anywhere

@haisss1 3 жыл бұрын

could we run it tube less ? i have 26x4 fat tyre, what size armour shou i use? thanx

@RideTannus 2 жыл бұрын

Sorry, we do not offer a Fat Tire Tubeless version. We do offer our Tubed Armour for you though. tannusamerica.com/products/tannus-armour?variant=31871966216303

@kengunnett2017 2 жыл бұрын

A local shop quoted me $40 a wheel to install these.

@bobgeldoff9413 13 күн бұрын

once again no one has said what they can resist.thier not cheap.so for this money i expect 100% protection.itrs not like their a cheaper solution.plus how much smaller tubes? could i get away with 1.95-2.10 on a 2.8" tyre??? or is not problem with pinch flats.also vould you use tpu tubes this seems a better use can tpu tube have puncture proof slime in and could you use it here also with the Tannus Armour for complete piece of mind or maybe slime tape with this tannus is more then enough for 100%

@mike8654 2 жыл бұрын

no way in heck. I've gone 3 hours and can't get the armor to seat correctly. The initial insert of one side rolls over and won't stay up against wall it rides in the channel and won't move up and out of the way.

@murderyurface3595 4 ай бұрын

Get a bag of zipties & use them to hold the tire tightly to the rim as you work your way around it. You shouldn't have many zip ties left when you're done lol Oh & a little dish soap on the tire on the area that has to go over the under the rim helps alot

@Alusnovalotus 2 жыл бұрын

Sadly, these didn’t work at all for me. A small nail ran right in and now I have to patch the tire but it’s a lot harder to get the tire off. Any suggestions on how to do that??

@RideTannus 2 жыл бұрын

Hi alus! Sorry to hear about the nail puncture. To get the inserts out all you need to do is reverse the steps shown by quietkat. Tire levers will be your best friend. Cheers

@Alusnovalotus 2 жыл бұрын

@@RideTannus awesome. And you are right, they’re life savers

@dannydanix8698 Жыл бұрын

Thank you for the video bruh, you explained it very well. My only question is does it work for a Super 73 fat tire 20" 4.0 ?

@cookiepopps5673 Жыл бұрын

Do they come in fat tire 20×4.0 and how much please?

@RideTannus Жыл бұрын

Yes they do! We would recommend our 20 x 3.0-4.0 tire insert. Thanks

@danielborowik7003 Жыл бұрын

i've ordered 2 sets of tannus 26x4" armor and both dont fit on my paselec gs9 pro 26x4" fat tyre ebike, the armor is so tight on one side that there is no room for the 26x3 tubes that i have bought let alone to fully install it, am i doing something wrong or do i need a next size up and if so what should i go for, can anyone help

@bobgeldoff9413 13 күн бұрын

i dont have the luxury of easily removing my rear wheel so i want full protection with no fucking around every 10 mins with a puncture

@mrdre9241 2 жыл бұрын

I broke three tire levers trying to do this…

@theantiqueactionfigure 2 жыл бұрын

I've owned motorcycles that didn't have that much tire to work with, Lol!

@syberphish 6 ай бұрын

I have to do this without being able to take my front wheel off the bike... they hid the disconnect up inside the frame. Joy.

@jazwraps7178 2 ай бұрын

Its an absolute clown joke you installed it that easy.

@drrobotnikmeanbeanma 2 жыл бұрын

Do they make Tannus Tires for 20" 4.0.If so where to get them what website and what's the name of the Tannus Tire.A Tannus Tire is something that never gets a flat ?

@RideTannus 2 жыл бұрын

You can shop them here: tannusamerica.com/products/tannus-armour?variant=32211843580015 . We do offer a 20x3.0-4.0 Armour Insert. Thanks

@joebyrneMensrights 2 жыл бұрын

These things flatten to about 1/8 of the original thickness and cause flats.but I guess you know that by now .

@philliprice5980 2 жыл бұрын

How so?

@joebyrneMensrights 2 жыл бұрын

@@philliprice5980 pressure from the inner tube with down bearing pressure flattens these down to about 1/8 of an inch . The inner tubes. Slips and ruptured at the stem and crimp the tire tube. twice before I noticed problem . I've started to see the negative reviews. Everyone that buys these will expierence the same thing. I ran them at the suggested 20 lbs .

@jazwraps7178 2 ай бұрын

Bout to quite bikes forever lol