Teach It Tuesday: Raised Vinyl Logo

Рет қаралды 38,145

6 жыл бұрын

Byran Hale show the process of doing a raised logo in a Vinyl panel.
If you have any question leave them in the comments and we will work to answer them.
If you are in the area make sure you stop by the shop and take a look around:
425 SE Dallas St
Grand Prairie, Tx 75051
Instagram: @gprodandcustoms
Facebook: @gprodandcustoms
Twitter: @gprodandcustoms
Bryan Hale: @the_koalamaster74

Пікірлер: 39

@jakemartin4305 3 жыл бұрын

Damm I didn't think that small piece of vinyl would stand out so much that awesome 👌

@DJDOUBLE077 2 жыл бұрын

This channel should have way more views.

@daboss59 3 жыл бұрын

The Mystical Veil was Dropped ! SO simply explained. THE Limit is leaning towards the Basics. Then challenge with bolder options as Skillset improves. Thank You Thank You

@battleop 10 ай бұрын

This is how we did this in the 90s. Today there are a lot easier ways to do this. It's important to know how things were done in the past so you can learn new methods to make things more efficient.

@jesseambachtsheer1138 3 жыл бұрын

was just thinking about how this is done! great video!

@taylorg223 4 жыл бұрын

Thank you for this amazing video !

@dave5833 3 жыл бұрын

Well done Sir. Thank you

@myoneblackfriend3151 Жыл бұрын

Excellent!!!

@nurseratchet8535 3 жыл бұрын

That is slick, thanks!

@MrCbell57 3 жыл бұрын

First time I've seen your channel. I'm interested in setting up a table top router that I can access and change bits quickly. Do you have a video on the set up or instructions on how to create your router set up? By the way I like the raised vinyl panel. Was that a special lettering set designed to be used for embossing?

@ivanrodriguez346 3 жыл бұрын

Thanks for sharing

@BigRichEHhthang100 5 жыл бұрын

Great work ‼️💯 I would love to learn how to do this

@josepheustaquio5544 3 жыл бұрын

well, you kind of just did right?

@nickross6025 2 жыл бұрын

Hey super cool video for sure, where can I get a table saw like that

@sayeedbaig8348 4 жыл бұрын

Very CREATIVE nlce.

@eross21 Жыл бұрын

what kind of vinyl is this? and what adhesive is that? i can’t wait to try this at home

@josepheustaquio5544 3 жыл бұрын

Damn. Impressive.

@bobrossi1185 4 жыл бұрын

very nice

@joshmartin8856 2 жыл бұрын

Would you consider this for door panels? I'm trying to create some early 60s Ford panels and think this might just be the ticket.

@hassanafrej4037 3 жыл бұрын

👏 bravo

@soldiercoleone Жыл бұрын

Ok I got me router table for my birthday and I'm looking for a 45 degree chamfer bit I like how the piece you made had a nice angle anyway I went to look to buy one and they had all kinds of different sizes and I'm stuck

@joserildocarvalho6510 2 жыл бұрын

👍🏼💯

@halojump123 3 жыл бұрын

Betty Goood!!

@michaelthompson9127 2 жыл бұрын

Hi what glue are you using?

@rosswhitaker1200 3 жыл бұрын

I know this video is a couple of years old, but another option that would take less of a steady hand and be cut precisely, is using a cricut and 3mm foam

@jakefriesenjake 3 жыл бұрын

Was just thinking about that. My sticker girl down the street has the little machine. Another perfect use for it. I had her make me stickers to use on my stainless steel radiator plate on my 81 Camaro. I then etched the steel with voltage and saltwater q-tips. I then removed the sticker to reveal the etched "Z28" logo. Simply perfect results.

@jeremybeals4394 2 жыл бұрын

How would you go about doing the same thing on vinyl intended for a seat rather than a solid surface?

@macswanton9622 2 жыл бұрын

Glue down to stretched canvas instead of mdf board

@matthewinga9546 6 жыл бұрын

What was the logo piece made from? So print the logo on paper and lay it on top of what?

@danialhowe9814 3 жыл бұрын

ya i wasn't clear on the either

@debd7803 3 жыл бұрын

The paper was on top of vinyl and as he cut the logo out it also cut the vinyl that was going to be underneath to make the raised area under the main layer. At least that's what I saw. But yeah he kinda didn't fill in a little gap there. And this question was a long time ago!! Just felt like i had to reply! lol

@jakefriesenjake 3 жыл бұрын

Yeah, the material was black vynal logo under the gray vynal, used to raise the letters. Foam could work too, or anything with the thickness you like.

@ariesr4883 4 жыл бұрын

What kind of adhesive did you use on this project?

@ariesr4883 4 жыл бұрын

Yes also which adhesive do you prefer for quick permanent repair and technique for vinyl coming out of a corner slot of a door panel? Btw love how you use the overspray and not waste any material or get your workbench sticky :)

@cotocan 2 жыл бұрын

@@MooreCulture Hi, I'd like to know which glue you used on the wood. Thanks.

@bleedinblue5675 5 ай бұрын

6:40…….giggedy…

@williamtellify 3 жыл бұрын

What a tool. very arrogant. Router king, looks like you need a very good router with lots of bits. thanks for sharing. lots of luck in the future. looks like you have lots of experience,