Mosfet IRFZ44N 1300W Hi-RES audio amplifier. In today's video I make an ultra bass amplifier using Z44N mosfet transistor. Please like and subscribes my channel. Thank you all ! #technicalDIY #diy #amplifier #ultrabass
Пікірлер: 1 200
@technicaldiy3 ай бұрын
*DIY Powerful Ultra Bass Amplifier SSD Computer , No IC , Simple Circuit* kzfaq.info/get/bejne/hrx-ZcyivdyZm5s.htmlsi=jPtXuJCVo-xog2hT
@user-ih6pu4pm3z2 ай бұрын
Oye y si kiero k levanté unas 4 bocinas d esas omas grandes Sele ponen más integrados d audio
@oorkruiser3 жыл бұрын
This is more like art than electronic achievement
@edmilsonrodrigues77343 жыл бұрын
Gostei 👏 parabéns ficou show de bola 👏 obrigado.
@mypopcorn88582 жыл бұрын
Galing na man salamat sa pag share ng talent mo bro
@arnaldooliveira76272 жыл бұрын
É pelo menos neste esquema eu estou vendo a fonte de alimentação, porque teve um outro vídeo com tipo 122 e 127 , mais um triponte que não mostrava entrada da alimentação. Vc esta de parabéns.
@kleyfram87922 жыл бұрын
Parece ser tão simples de fazer
@cyberhiper2 жыл бұрын
This is a Class A amplifier, output is approx. 2.5w with 12v power supply.
@yourethebest73452 жыл бұрын
That's what I. Saying it won't produce more than 10 watt in it's maximum voltage at 60v where as MOSFET power limit is at it's peak according to datasheet and being class a it's highly inefficient amplifier I don't know why these people fool other saying it's 1000 watt something like that
@westelaudio9432 жыл бұрын
There are class A amps like this, their power is in the mW range and gain is very low. However this one isn't even set up correctly. There is nothing to AC couple the speaker to the output, so a) the power resistor is useless and b) the DC offset would keep the cone off center all the time. However, the cone is not moving a bit when he connects power, and also no crackle when the jack is hooked up. My guess is, he hid a small amp module in the "power brick", connected via bluetooth. The "power rail" carries the actual audio signal, and enters the speaker through the medium sized resistor and ground.
@gordonwelcher95982 жыл бұрын
He is misleading people by posting these barely functional circuits with ridiculous ratings. Some are dangerous or will burn out the speaker. Why do you think manufacturers use so many more components to get a proper operating safe circuit? How many people have wasted their time with the garbage he posts?
@Uraim Жыл бұрын
@@westelaudio943yes actually, when he places the battery on the table, there isnt any sound when the table and battery collides. also the battery is modified, its obvious, also based on calculation, side of the battery says, that its a 6volt battery actually. if we calculate the output wattage, it no more than 0.28Watt, or 280mW. Also when he connects the speaker, or the battery, if the speaker is already connected, there isnt any bumps, most of his diy amplifier isnt working in real condition, i didnt told you new thing i guess.
@Uraim Жыл бұрын
@@gordonwelcher9598 i actually once blew up my player :) like years ago, luckily i just had a 2-3$ mp3 player, due the decoupling capacior on input was reversed, and i decided to give power to little baby, (i used +12v and -12v on an atx psu.) note: it was 3years ago when i not even had solder iron, nor knowledge about amplifiers. today i built a nice 15watt amplifier for 4ohm, its an AB class amplifier based on quasi complementary pair, giving a whopping 35Volt for voltage rail, it draws half an amp on max volume, it have negative feedback to decrease distortion, it have bootstrap for additional power from the driver, it was a nice project. 2 transistors on the output, (two 13009) and for a driver: c1885 and a912 pair, and a c945 where the signal is boosted from aux.
@user-wo1lu7hs2p3 жыл бұрын
ขอบคุณครับ. หาของเจ๋งๆมาให้เล่น เบสสุดยอด
@richardndikumana29703 жыл бұрын
Est ce que cet amplie na pas de parasites!????
@finochachalaco76883 ай бұрын
No hay ninguna duda de que eres una persona muy especial y profesional que bárbaro gracias por compartir tus conocimientos y experiencias con tus amigos y seguidores gracias por compartir tus experiencias con nosotros tus seguidores 😉 😊 👍 🙌 🙏 😊😊😊
@shahdevice30862 жыл бұрын
ooooOOOOO SSSSuuuummm dude !!!!! Your system took me 14 years back in my life , a music lover teenager , who used to die for a sound experience from a Panasonic 5 Cd Changer Sound System with 3D Sround and Wide Equlizers and Bass and Loudness and what not .. But financially , all he had was AM radio scanner, and a half broken Cassette player ... OMG man that was my time I had an idea of making a circuit that could work like an Amplifier ... But people told that kid , that his idea was not implementable ...
@prprojetos97263 жыл бұрын
Congratulations blessed ball show stays with God hugs
@alexanderkuhn2298 Жыл бұрын
Good job, connecting the battery right up to the speaker, cause that will totally work. For once I thought you were going to build an actual class A amp, but nope, lots of issues with your “circuit”
@gilbertovilchis76862 жыл бұрын
GRANDE GRANDE GRANDE, MARAVILLOSA APORTACION PARA EL MUNDO,GRACIAS.
@InventableESPT2 жыл бұрын
Aportación? Que aportó, mentiras eso es el aporte que te da, sabes que el video es falso verdad? el amplificador a lo mucho da 3w de potencia, bueno todo el canal miente, de esto no se aprende anda
@JoseRamirez-xc9dg2 жыл бұрын
Una pregunta.... la caja azul es una batería y de que capacidad
@locuragamersclub69422 жыл бұрын
@@JoseRamirez-xc9dg es 12 v es la batería que usan las alarma
@oorkruiser3 жыл бұрын
Impressive for such a simple circuit
@pedrofm52773 жыл бұрын
Muito bem explicado
@hugohernandez22892 жыл бұрын
excellent video I see what you do congratulations hand up
@CristianoVakisswinnerBarrosАй бұрын
Done is more than the perfection!
@rhs1062 жыл бұрын
Cara!meus cinseros parabéns pela excelente qualidade do seu vídeo. Parabéns!!!!
@user-ju6rm6wu9g3 жыл бұрын
God work. ..and easily to make. .thankfully
@tamirathailu8101 Жыл бұрын
Excellent!!! your are making an advertising for Microsoft surface too!
@LakhwinderSingh-gx7jk3 жыл бұрын
Beautiful sir
@danyvillanueva34462 жыл бұрын
muy buen video bien esplicado me gusta la electronica y me gustaria aprender
@edgararturogarciaportillo37992 жыл бұрын
Los cálculos de potencia para este circuito son 4.5 watts rms max. Considerando Vf=12v, y el amplificador clase A entrega un máximo de Vf/2, es decir la bocina recibe máximo 6vrms, y con 8 ohm de impedancia, la potencia es P=V*V/R, (6*6)/8= 4.5W Corrijo, esta potencia no es RMS, es potencia peak, gracias por la observación a 歸虛
@misterioznicoveculjak64612 жыл бұрын
hahhahahahhhhaa 4,5? 1w max
@FederacionFunk Жыл бұрын
Hola, y como se calcula la ganancia de este circuito?
@murat-tj5hl Жыл бұрын
Hesap çok iyi
@qddk9545 Жыл бұрын
I am sure that it is at least 10,000 watts 🙂
@luispirela1128 Жыл бұрын
Edgar y como se hace si quiero colocarle otro speaker ? gracias
@Noalaagenda2030Marioneta-jf1jw Жыл бұрын
Excelente saludos desde Metán Salta Argentina
@Craftcorn_br3 жыл бұрын
Show de bola amigo vou fazer um dese
@sahirraupe75073 жыл бұрын
Bisa buat dengan volume bass dan trablenya dong
@shahdevice30862 жыл бұрын
Bro , you know what , I am not an electrical engineering student , so I dont understand in depth, but I can follow you, the way u did in this video .. Can u make a video for a circuit that inputs music from my laptop or phone , and it must add High Bass , and Loudness & Equilizer sort of functions ??? It would be a blessing
@awalelectronics79542 жыл бұрын
kzfaq.info/get/bejne/fq2kgsmqz7jHeZ8.html watch video about Ak amp
@Uraim Жыл бұрын
no, dont do it, it will result in your phone/laptop input audio will gonna go in smoke, study first, also i would not recommend following this guy, due his amplifers are deadly for mobile and laptop input use.
@alexanderkuhn2298 Жыл бұрын
If you are interesting in electrical engineering do yourself a favor and dont watch these videos, there are much more credible sources elsewhere
@joelmathew3733 жыл бұрын
Can you make a video for making amp for using guitars pls
@Juniorfinger9993 жыл бұрын
Kembali lagi sperti biasa, ini ter kongkrit bagus jleger bom.. wow amazing
@bolamick32782 жыл бұрын
Show vou montar tbm 😸
@Matutosdapaz-l8c2 жыл бұрын
Qual trânsistor ele usa ????
@juninhocastro953 Жыл бұрын
@@Matutosdapaz-l8c IRF44ZN
@djedbrasil90193 жыл бұрын
Congratulations... excelent!!!!!
@kaylanekamilly79072 жыл бұрын
FICOU BATENDO PRA DENTRO MAS FICOU ÓTIMO...
@endersimancas5717 Жыл бұрын
Es excelente amplificador
@cleusnipilantil5020 Жыл бұрын
Vou fazer um ficou muito show. Qual essa música também muito top
@ibnurulyanto12182 жыл бұрын
Can use potensio for increas or dicreas?
@billimacompositorbl65742 жыл бұрын
Muito massa...ganhou mais um inscrito 👏👏👏👏👏
@rajneshkumarrajnesh9557 Жыл бұрын
Agar yah savan to dikha rahe hain aap vah bajega nahin to
@esmeraldaguadalupeperezher4032 жыл бұрын
Excelente,pero vieras metido la bocina en una base o una cubeta de agua para ver que tal el sonido encerrado.saludos desde Campeche,Mexico
@Oliveira_jr30_Oficial2 жыл бұрын
Mais inscrito amei... Sem. Contar que estou cursando T.I.C
@davpro17922 жыл бұрын
That's like 1 watts at maximum, 1300w would blow that speaker it would be bottoming out really hard smoke and blow, lol
@moisesflorencioarcelino15693 жыл бұрын
Muito bom e xou de bola parabens l
@Mr.Ghostmix Жыл бұрын
watching and sending support thanks for sharing shout out host
@modeDEEJAY2 жыл бұрын
Nice job bro! Congrats!
@sergiosom38313 жыл бұрын
Muito bom, gostei do projeto
@nicatronelectro6946 Жыл бұрын
10 Watts only,. IT is better if do you give us the diagram ...
2 жыл бұрын
Excelente, buena calidad de sonido. Muy económica y eficiente.
@manu-062 жыл бұрын
neeee este video es muy falso
@juliopena23362 жыл бұрын
@@manu-06 porque???
@manu-062 жыл бұрын
@@juliopena2336 no existe un amplificador clase a con 1300 watts ._. Este proyecto a lo mucho 12w
@juliopena23362 жыл бұрын
@@manu-06 pensé que cuando decía que era falso, se refería a que no funcionaba nada. Es de lógico que ese circuito no puede dar tan alta potencia. Gracias
@warjitowarjito9492 жыл бұрын
Dah nyoba gak bisa keluar suaranya
@imanudin6653 Жыл бұрын
Mantab terimakasih atas ilmunya semoga sehat selalu aamiin. Bang
@amsalbatubara952 жыл бұрын
Thanks for tutorial... that's wonderful
@thomaswomack38882 жыл бұрын
while what you did is impressive... it is simply impossible to get 1300 watts from a single ended amplifier running on 12vdc Even if you double the voltage you will never get anywhere near 1300 watts from a single discrete transistor. The laws of physics and amplifier design havent changed. You might be getting between 4 and 5 watts out of your amplifier. Single ended amps are power hungry monsters and can only claim around 40% efficiency. So measure the current draw from your battery and multiply that by the voltage of the battery under load and that will tell you what the amplifier is drawing from the supply. The power output will be only about 40% of the input power. And you absolutely cannot get more power out than you are putting in!!!
@herowillrose31982 жыл бұрын
You are electrical and electronic engineering. No one dare to changed ohm laws nor physics, but one could only adding and subtracting. This project for mimicking purposes, if assembler want to exponentially functional circuits, he must have the right ohms laws for his output satisfactory.
@gordonwelcher95982 жыл бұрын
He is misleading people by posting these barely functional circuits with ridiculous ratings. Some are dangerous or will burn out the speaker. Why do you think manufacturers use so many more components to get a proper operating safe circuit? How many people have wasted their time with the garbage he posts?
@juliusortaleza1486 Жыл бұрын
1300PMPO possible 😅 lol
@mihaipaun83611 ай бұрын
Cred că depinde mult și tensiunea de intrare ( semnal )
@oberst_krass11 ай бұрын
@@juliusortaleza1486in PMPO everything is possible.🤷🏻👍🏼
@zachrytaskn13303 жыл бұрын
süper okul purojesi ❤👍
@skhosanamathiyane3 жыл бұрын
Wow man,,,,,,,,South Africa
@naseemahmad58322 жыл бұрын
Amazing video
@subutayozselanikli3 жыл бұрын
Try to use F-CK69 Gaetanium transistor, it will give 10.000W or how much you want. Don't forget to use Shitanium filter caps for output.
@nodriveasusephotos80192 жыл бұрын
what are the filter caps for?
@Matrix...7772 жыл бұрын
🤣😂🤣😂🤣
@user-qq5hz2qb9c3 жыл бұрын
Я в детстве тоже усилители собирал,только маркер тогда ещё не был в ссср,а так бы я нарисовал ,что у меня динамик10гигаватт
@karantechnicalproject64732 жыл бұрын
Nice video sir 👍🏻👍🏻👌👌👌👌👍🏻👍🏻
@GoKreatif3 жыл бұрын
good job bro
@user-on3kn8ii3w3 жыл бұрын
улыбнулся)))
@user-tf9fk4ph8h2 жыл бұрын
Бред какой то?
@user-on3kn8ii3w2 жыл бұрын
@@user-tf9fk4ph8h рофл!)))
@williammelo8802 жыл бұрын
Mas, valeu o vídeo, me lembrando aqui qdo trabalhava na ind.eletronica, eu fabricava as placas de circuitos impresso.
@maurolx3 жыл бұрын
congratulations on the video, simple and amazing..!!!
@bongpenafiel13862 жыл бұрын
Ang galing mo talaga idol gawa mo ako nyan
@LakhwinderSingh-gx7jk3 жыл бұрын
Sir, please make this circuit in the supply of three faces please
@LuiguiGamer12 жыл бұрын
En la caja de descripción pude observar por lo menos 2 mentiras: 1300W y Hi-RES. Haces buen trabajo creando pero por otro lado no mientas.
@jorgecontreras76312 жыл бұрын
Si si es verdad, lo le dije son 1300 Watts de consumo, va ni eso, 1300 Watts RMS jamás puede ser 😀👍
@CarlosReyes-tp5cw2 жыл бұрын
Es genial voy hacerlo
@Learnelectronics7383 жыл бұрын
Great you video amplifier small
@amitdhasmana19882 жыл бұрын
How would you remove humming sound while conducting to transformer Ac-to-Dc ?
@CreativeTechos2 жыл бұрын
Simple tested solution Connect 1uf poly cap between audio input + and ground.
@tonywalman3 жыл бұрын
With this single ended drive, the max power output can be easily predicted by the supply voltage and speaker impedance....
@tronetrickard71302 жыл бұрын
Can i use this circuits for boost dc volt?
@westelaudio9432 жыл бұрын
There are class A amps like this, their power is in the mW range and gain is very low. However this one isn't even set up correctly. There is nothing to AC couple the speaker to the output, so a) the power resistor is useless and b) the DC offset would keep the cone off center all the time. However, the cone is not moving a bit when he connects power, and also no crackle when the jack is hooked up. My guess is, he hid a small amp module in the "power brick", connected via bluetooth. The "power rail" carries the actual audio signal, and enters the speaker through the medium sized resistor and ground.
@kilo_alfa2 жыл бұрын
Beau travail, merci pour le partage. Félicitations du Maroc 🇲🇦🇲🇦🇲🇦
@mr.van98313 жыл бұрын
Ông này là ông anh thợ điện mà Chắc chắn
@hieupham50432 жыл бұрын
Hàng VN mà làm tiêu đề tiếg anh tưởg hàng ngoại
@wilsonbell35163 жыл бұрын
4.36 из под радиатора выбегает таракан аудиофил))))
@robertoloyola16393 жыл бұрын
fala sério nunca daria essa potência toda..
@kingedtz45223 жыл бұрын
Kkk né isso kkk
@adrianocordeiro86433 жыл бұрын
Deve ser esses cara que fazem os mini-Sistem das casas brazoca hj em dia kkkkk. Consomem 10w e reproduz 1300w
@kingedtz45223 жыл бұрын
@@adrianocordeiro8643 kkkkk Nem classe D com 90% de aproveitamento kkk
@rahulpatelgujratahmedabad34973 жыл бұрын
Good tiching karte hai 👍👌👌👌👌👌👌👍👍👍👍👍
@dusblb10 ай бұрын
luarbiasa....ilmunya...
@carloszambrano32273 жыл бұрын
Excelente amplificador, gracias..!
@luisdamianduran27443 жыл бұрын
Ati te funcionó??
@carloszambrano32273 жыл бұрын
@@luisdamianduran2744 Saludos, aun no lo he armado aunque tengo todos los componentes.
@manu-062 жыл бұрын
@@carloszambrano3227 noooo bro no te da 1300w A lo mucho 10
@carloszambrano32272 жыл бұрын
@@manu-06 eso es correcto, no más de 10w.
@manu-062 жыл бұрын
@@carloszambrano3227 ci y además un amplificador clase a no puede pasar los 30w
@coratelasac78443 жыл бұрын
Excelente, muy buena
@Suavache2 жыл бұрын
Mạch công suất âm thanh bé mà khỏe phết của nhà nhỉ
@rambebeton44833 жыл бұрын
Mantap brooo
@forropezadomaninhodostecla70143 жыл бұрын
Vc tem o layout desse projetinho?????
@syariefhelmi9709 Жыл бұрын
what voltage and watts do you use as a power supply?
@completeselular35012 ай бұрын
Batrainya berapa volt
@paulobastosbastos4026 Жыл бұрын
show ,muito bom
@SolderAngek2 жыл бұрын
Nice share.. Amazing 👏👍👍
@milenbuinov3843 жыл бұрын
this small speaker is 50w and this amplifier is 20w max
@user-go6dy7eo5h3 жыл бұрын
Не 50,а 5-10 от силы но чуйка возможно не плохая😅
@milenbuinov3843 жыл бұрын
@@user-go6dy7eo5h 10w speaker is printed. on magnet
@paolbackman6513 жыл бұрын
You wrong, this transistor have P_max 94W and speaker have the sign 500W written with permanent pen, by a simple calculation we find the power (500+94)*2=1188 and this is almost 1300W. Amplifier ofcourse works in Class PM(perpetum mobile) and speaker is constructed from very advanced materials and cheap sticker on magnet :)
@user-go6dy7eo5h3 жыл бұрын
Мужики,вы меня дурите😄
@johnangel15122 жыл бұрын
@@paolbackman651 anyone can write 500W on a speaker, more likely a 10w speaker, freeze video where he's waving the speaker about 6min.50s
@joorsoerowirjo77002 жыл бұрын
I like these simple designs....very easy to build for beginners. But 1300watts with a single fet from a 12v battery.....that's impossible.
@awalelectronics79542 жыл бұрын
Yes Ak power amp version 1.0.1 brother AB mode per work karta hai 12 volt sai 30+30 volt(28.4 ampere) create karta hai kzfaq.info/get/bejne/fq2kgsmqz7jHeZ8.html
@jinkazuyatvlogs93322 жыл бұрын
Just try and you can tell💪
@gordonwelcher95982 жыл бұрын
He is misleading people by posting these barely functional circuits with ridiculous ratings. Some are dangerous or will burn out the speaker. Why do you think manufacturers use so many more components to get a proper operating safe circuit? How many people have wasted their time with the garbage he posts?
@Ampsinthejump3 жыл бұрын
A simple design, but it will suffer some distortion.
@mrcheaspk31732 жыл бұрын
Good idea i like 👉🎬
@marcoscapote5873 жыл бұрын
cara gostei muito, só que a ligação do falante está invertida né? batendo pra dentro , o certo é para fora
@rogeriojesus75442 жыл бұрын
Esse alto falante ai 500w😏
@chathucreations51762 жыл бұрын
How much is the output watt ? How much power and Ampier should I give?
@starmakercoversongs51862 жыл бұрын
1000000v or fack
@patrickmcmanus53732 жыл бұрын
Please do one in 9 volt. Thanks for all your videos. 💜👍
@CristianoVakisswinnerBarrosАй бұрын
❤❤❤❤❤❤ what a great help!!!!
@wlsnpndrvs85932 жыл бұрын
Wtf? My Peavey Max amplifier had 24, 150 w Darlington power transistors in it, and it was 400 Watts per channel RMS.
@natalinoviana3 жыл бұрын
Será que pode usar uma fonte de 12volts ao invés da bateria?
@ramos32463 жыл бұрын
Ele usou bateria porque dificilmente temos em casa fonte de 12 volts que forneça amperagem alta. Para esse falante de 500w em 12 volts nesse circuito a fonte precisa entregar 41 amper de corrente para usar a potência total do alto falante. Mas dá sim com certeza, só que a fonte deve fornecer no mínimo 41 amperes , caso a fonte forneça uma amperagem inferior ao que o falante de 500w precisa, ele não vai entregar tudo que pode.
@smartchoiceassistenciatecn47212 жыл бұрын
@@ramos3246 será que vira testar em um carro?
@micasaveiro2 жыл бұрын
essa bateria é de 12volt 12 amperes
@arttechvision2 жыл бұрын
Amazing....
@gadirajurambaburaju97903 жыл бұрын
Nice 👍
@joseluisdossantos60453 жыл бұрын
Ótimo
@alexejditz25532 жыл бұрын
Ребят когда он показывает динамик посмотрите там 10 ватт 8 ом😂
@lariontt Жыл бұрын
Классный музон💥🔊🥁🎶
@manoeldalapaconceicaosanto54203 жыл бұрын
Vou tentar fazer um desse para ver se dar certo dessa potência
@adrianocordeiro86433 жыл бұрын
Máximo 20 wats e sem qualidade o falante só vai reproduzir meia onda. .
@engineerkohat2 жыл бұрын
Great work. So much views. 1300W is not a joke.
@kennmossman87019 ай бұрын
use Ohms Law it is IMPOSSIBLE here to get 13000W
@ribeirotecnico71802 жыл бұрын
Projeto muito bom gostei Nossa passou uma barata? Rs
@Gans_G2 жыл бұрын
Siiii, también la ví
@oprekasik81922 жыл бұрын
keren pokoknya. 👍👍
@music_and_legend2 жыл бұрын
Achei a música que o @mw informática usa kakkakakak parabéns pelo vídeo
@user-hg6qj5ig6m3 жыл бұрын
От 12 вольт как то попахивает вранье
@user-zk2pn7ds6b3 жыл бұрын
Да неа, вполне рабочий вариант. Только качества звука желает лучшего
@user-wi5hn7wy3d2 жыл бұрын
При 12 вольтах? 1300 ? КПД-1000%-прорыв в физике,понятно,что у них другой "ГОСТ".
@rsehaber3 жыл бұрын
1.300w? Or 13w?
@sltrickshow30483 жыл бұрын
13 w 😁😁😁😂😂
@waik01823 жыл бұрын
This amplifier delivers only 8w
@suhermancogreg83432 жыл бұрын
Mantaaap bang.bisa buat jual di pasaran ni..di toko toko udh ada blm bang hasil karya nya