Suction Pump Installation

Suction Pump Installation | Piping

Рет қаралды 198,766

7 жыл бұрын

This video explain Suction Pump Installation method
video source/thanks to www.sintech.in/
Watch More Piping Videos....
1.Layout and Development of Pipe Branch 90 degree : • Layout and Development...
2.Piping_How to read isometric drawings_Basic : • Piping_How to read iso...
3.Pipe wall thickness calculation as per ASME B31.3 : • Pipe wall thickness ca...
4.Piping_Fabricate 45 Degree Elbow(miter bend) from pipe : • Piping_Fabricate 45 De...
5.How to fit up pipe to 45 deg elbow? : • How to fit up pipe to ...
6.How to fit up pipe to flange? : • Piping symbols In isom...

Пікірлер: 49

@moirah1234 7 жыл бұрын

Very informative. Thanks

@jiarahat5302 7 жыл бұрын

very good information thanks

@piping-cadtutorial 4 жыл бұрын

The video is very helpful. Thank you about information you provide.

@TECHNICALPIPING 4 жыл бұрын

Thanks.share to all

@nags8482 6 жыл бұрын

Would have added more info on the piping alignment or allowable deviation in between piping flange and pump nozzle, allowable shaft deflection during buttoning up the flanges.... Grouting details would have given more details like grouting method, clearing of blow holes or defecting grouting, final grouting....

@djoudjou1214 6 ай бұрын

I liked your upscale page posts

@ibsarkhan3770 4 жыл бұрын

Shouldn't we use 3D or 5D of spool for ecc red from suction?

@lighttv3770 3 жыл бұрын

Informative

@kanthan4729 3 жыл бұрын

We should open the discharge isolation valve to lower the load on the prime mover? right?

@user-nb5dh9ry5j 6 жыл бұрын

هل هونا ك مضخاط ضغط مركزي لها القدر على استخرج المياه مسافة 80 متر بئر جوفي

@HalftoneCHANNEL 7 жыл бұрын

without grouting between foundation and base you can expect excessive vibration and noise

@aditya05umrao 6 жыл бұрын

In which plateform this video made?

@SRINIVASAMBADI 6 жыл бұрын

What about cavitation formation when we use flat side bottom eccentric reducer in positive suction head.

@sowmantung6457 6 жыл бұрын

Ihave the same Question relate to Esentric reducer

@calonpresiden3468 4 жыл бұрын

Good animation

@RT-kh8rg 5 жыл бұрын

How do I located the suction line and discharge

@mantvtor8305 4 жыл бұрын

good animation

@SkYadav-po6jk 5 жыл бұрын

Good

@drewhartley6472 4 жыл бұрын

Please have just one background music reduced level during the dialogue and kill the other beat music it’s distracting from what otherwise is a very informative film 😎

@cmmc116 7 жыл бұрын

Hi, new subscriber here. A question. The 6% slope is absorbed for the inlet gasket?

@phiksit 7 жыл бұрын

You would have to make a angular / mitered fit up at the eccentric reducer to get your slope.

@user-pq8pw5wo1r 6 жыл бұрын

yes

@MTA141 4 жыл бұрын

Hi Technical Piping, i have a question: Why we should fit eccentric reducer, maybe can make avoid air pocket formation? Thanks a lot!

@ansarbaig7183 2 жыл бұрын

Old practice advised to use Ecc bottom flat but latest engineering practice says to use Ecc top flat no metter whether tank is A/G or U/G in order to avoid flowing bubbles in pump.

@khalilahmad882 3 жыл бұрын

Gr8

@naglp7981 7 жыл бұрын

please tell me how to select size of pipe

@silambarasanveerachamy3453 7 жыл бұрын

Nag Lp it's depends on the pump nozzle size...

@nags8482 6 жыл бұрын

Pipe size selection is based on pump nozzle size, pump nozzle size is based on process flow and head requirements. Types of pump selections are different and need to consider process and site conditions

@balyanharahap899 5 жыл бұрын

at 2:55 how long the minimum pipe after reducer?

@santhalakshmi172 5 жыл бұрын

@mantvtor8305 4 жыл бұрын

please explain and make video vibration standard of pump

@saudkw92 4 жыл бұрын

Why isn't an isolation valve recommended?

@rajkumar-tk8dz 6 жыл бұрын

sir ,please make ur vedio in Hindi also

@niyonsengaolivier563 5 жыл бұрын

please share your video to us

@shaginpaul5488 2 жыл бұрын

Brother please mention standards accordingly...for reference..

@Komeh_ 2 жыл бұрын

arent we supposed to use a minimum of 5D rather than 3D?? API 686 Specified a minimum of 5D, please clarify. thanks

@dixonaloysius1366 5 жыл бұрын

the background music is interpreting the voice

@artin4580 Жыл бұрын

inclining upwards 6mm for 100 mm is wrong in. it is 6 mm for 1000 milimeter

@ansarbaig7183 2 жыл бұрын

I am piping designer and I have worked in JGC Japan. Please improve yourself as described below. 1.Discharge piping on the nozzle is not good practice. Load on pump nozzle cause disturbance of pump alignment. 2. Reducer with pump nozzle is not good. There should be 5d straight run between Reducer and pump in order to provide turbulence free flow to pump. 3. There is to be Ecc Reducer top flat even if flow is from A/G tank.

@AliAhmad-df2sf Жыл бұрын

Hi How can I contact with you !!! Plz reply I want to ask couple of questions.

@ansarbaig7183 Жыл бұрын

@@AliAhmad-df2sf Can you ask the question at this panel. Please introduce your self too. I Don't mind to render my services.

@samueljebaraj4742 Жыл бұрын

Why don't go for bottom flat bro for eccentric reducer ?? is there any standard reason in it ??

@ansarbaig7183 Жыл бұрын

@@samueljebaraj4742 Ecc B/F is an old practice. If you see American "piping guide" old version, there's same. However, the latest practice in most reputable companies like Technip, Bechtel, Florabia, JGC, Aramco & Adco is to keep Top flat as latest practice. The reason is to avoid bubbles generation in the upper cavity of reducer. The RPM of pump is 3000 or sometimes more, even the little quantity of bubbles attack the pump impeller like bullet which reduces the life of pump. Moreover bubble causes noise and vibration too. Piping Designing is a vast field, however Designing around pump is most easy and simple. If you are keen fully interested, we can share our views on every type of piping Designing in future.

@ansarbaig7183 Жыл бұрын

@@AliAhmad-df2sf how do you like to contact me?

@sovereignjocker2556 3 жыл бұрын

Kindly try to avoid this background music. So annoying and not able to listen to your explanation.

@neerajpokhriyal7958 Жыл бұрын

copy

@GemmyHeart Жыл бұрын

Main products: sealing gasket,gland packing,PTFE/graphite/asbestos products, ceramic fiber products, high temperature heat insulation and fireproof material. Free technical support (sealing, heat preservation, heat insulation, fire prevention problems) All products 1 piece can also be customized, 30 years of service experience, fast and safe shipping anywhere.