Tekno ET48 2.0 upgrades and XMAXX
Рет қаралды 1,521
Жыл бұрынFigured I Do video on this awesome upgrade for the ET 48 and some recent changes to the XMAXX
Center brace link for ET48
www.ebay.com/itm/403497536416...
M2C racing link
 m2cracing.net/
Swag and stickers link
inkmonkee.myshopify.com/colle...
@ekimyhael9964 5 ай бұрын
Thanks for the tekno brace install video ! Just got mine.
@BarstoneRC 5 ай бұрын
No problem 👍
@islandrc-duke1972 Жыл бұрын
Awesome RC and upgrades
@BarstoneRC Жыл бұрын
Thanks 👍
@Dos_Rc Жыл бұрын
Your welcome brother , I love that brace been running it on my et 48 2.0 since I built it. It’s about time you got it lol
@BarstoneRC Жыл бұрын
Yeah, I know you told me about it a dozen times I think lol I finally decided to do it. Thank you brother.
@hrivera9357 Жыл бұрын
I bought that one but from M2C,I installed yesterday and it just make my MT410 awesome,God bless u my friend 🙏
@averylooper5534 Жыл бұрын
Love your shoptime videos. Thanks for posting I always learn something on these
@BarstoneRC Жыл бұрын
Thanks for stopping by Avery. I appreciate it buddy.
@blacksheeprc8113 Жыл бұрын
Thing is great
@chadbiermann3380 Жыл бұрын
Nice little bench video!! Can't wait to see the Teckno out for its next bash!!
@BarstoneRC Жыл бұрын
Coming soon!
@omega_rc Жыл бұрын
Hey Bars if I could leave one humble opinion about the center bars for Teknos (I’ve used all racing and m2c center bars in my Teknos) is to not over tighten the screw that bolts down into the front top plate. Alot of pressure goes into that part and if it’s overtightened it will eventually break the small piece that holds that bolt. It’s happened to both center braces that I have used. Hope it’s some help awesome video again brotha! 🤙🤙🤙
@BarstoneRC Жыл бұрын
I appreciate the information buddy I haven’t talked to many people that use these yet, so it’s good to know
@omega_rc Жыл бұрын
@@BarstoneRC leaving it loose allows for some very slight flex and it will help from breaking the small piece, although when it breaks it doesn’t really make a difference but I’m sure you’d rather have it in one piece than two 🤣
@johnnyhaberfield721 Жыл бұрын
It's the only time of the year all my trucks are up and ready to go.Shame the weathers not.✌️
@BarstoneRC Жыл бұрын
I know everything‘s ready to roll and it’s cold and nasty out
@johnnyhaberfield721 Жыл бұрын
@@BarstoneRC I planned ahead and got myself a V5 kraton ,plus M2C XL kit and various other goodies to put together,keep me sane.✌️
@jacobhenson3952 Жыл бұрын
Nice man make sure you watch your temps with that stock motor it gets hot pretty fast. I put protek fans in the stock fan mount and it seems to help a lot but the stock fans are not that good I melted one stock motor with the max 5 but if you keep a eye on it then it’s not to bad.
@BarstoneRC Жыл бұрын
Yeah, I was beating on it pretty good for about 20 minutes straight the other day and checking it on and off. It was staying pretty decent so far.
@RC4us Жыл бұрын
That brace looks so sweet
@BarstoneRC Жыл бұрын
Really digging it and it works great
@RC4us Жыл бұрын
@@BarstoneRC good stuff
@peighday Жыл бұрын
That’s what I’m running as well. Stock motor with Max5 and WFO plate with 20/50 gearing. Also got the m2c wide kit and some DuraTrax Lockup. I think it’s a nice setup.
@BarstoneRC Жыл бұрын
Awesome setup
@livegood9876 Жыл бұрын
What are you running on the servo / servo saver again. All i caught was Hot Racing....? 9:53?
@BarstoneRC Жыл бұрын
I’m running the whole aluminum, hot, racing, servo saver, set up
@davidbegeotsr4025 Жыл бұрын
On the techno DJ does your battery still fit all right
@BarstoneRC Жыл бұрын
Yeah, the battery still fit good in there. I run the smaller ones in it the 4000 mA most of the time.
@lukerecore3211 Жыл бұрын
Is that a blx 185 amp esc and a blx motor??
@BarstoneRC Жыл бұрын
Yes it is.
The RCNetwork
Рет қаралды 28 М.
PrimeRC
Рет қаралды 3,4 М.
West Desert Wheeler
Рет қаралды 13 М.
RCDriver_Online
Рет қаралды 48 М.
ENZO
Рет қаралды 3,7 МЛН