Template Routing Basics

No video

Template Routing Basics

Рет қаралды 130,939

Күн бұрын

One of the easiest ways to duplicate parts is by using templates. Learn how to make templates and which router bit should you use when cutting around a template. You'll also learn how to set up your router or router table to make cuts around templates.
Subscribe to this channel for new weekly video woodworking lessons, tips and tricks:
/ woodworkersjournal
Get more FREE project plans, expert tips and tool updates in our weekly email newsletter. Subscribe here:
www.woodworkers...
Visit our website for the best woodworking projects and lessons:
www.woodworkers...

Пікірлер: 53

@joergwiesmann4261 3 жыл бұрын

thank YOU very much !!! kinde regards from Switzerland !!!

@sergiopadronarellano5437 2 жыл бұрын

The importance and use of templates!!! Thanks!

@russelllynch7606 2 жыл бұрын

Thank you for the clear explanation

@somedude3159 7 ай бұрын

Thanks for the flip the piece advice to utilize the bottom bearing

@ericschwartz9982 2 жыл бұрын

Very helpful video. I stumbled onto this while looking for resources for building my Adirondack chairs. What a coincidence!

@mgammill 6 жыл бұрын

Best video on KZfaq for table routing and direction

@BearXXII Жыл бұрын

Thank you! Very concise and clear!

@brianchester4218 6 жыл бұрын

That was the best video I have watched simple straight forward you should take up teaching if you don't already do so

@tammoton9494 11 ай бұрын

Just great.

@josemanuelnavarro6637 8 жыл бұрын

Great explanation for begginers. Thank you!

@tyronedeasbrailsford951 Жыл бұрын

Great information! Thanks

@DesignEcologies Жыл бұрын

Thank you

@politovski2000 5 жыл бұрын

Eres un genio !!! El mejor video de esta clase, muy bien explicado. Muchas Gracias por compartir. Saludos desde Argentina

@sssyntax 4 жыл бұрын

You are an excellent teacher !

@micro963 3 жыл бұрын

Thank you for sharing great video 👍👍👍how do I go by template routing 1/8” plywood, what type of routing bit do I need, do I have to be worry about grain direction?

@robertdominguez4003 7 жыл бұрын

This by far the best how to vidio iv'e seen so for.. Thanks...

@Commonsensenotsocommon 2 жыл бұрын

very useful thank you!

@GaylordBalzer 2 жыл бұрын

Great video.

@bevelededgewoodworks2649 Жыл бұрын

Nice video, what brand of carpet tape did you use? I found Shurtape brand that says it's permanent, not good!

@tanyawebb4137 7 жыл бұрын

This was a great video! What is the yellow grip tool that you were using to hold down the wood?

@Uncle_Buzz 8 жыл бұрын

You guys have been doing some extremely useful videos lately, thanks for that!

@hinduspl 8 жыл бұрын

wow.... this chair... hope you will get video how to complete something like that soon!

@Tipjar333 4 жыл бұрын

Well presented. Thank you.

@Chimp_No_1 7 жыл бұрын

Extremely helpful. Many thanks.

@gregoriorafaelfernandezmun8375 4 жыл бұрын

Hola......tienes plantillas de sillas adirondack reclinables...??..... Gracias.. saludos desde México ..

@DeanGrove 8 жыл бұрын

Also,what I saw from a Luthier here on KZfaq. Use masking tape (less sticky residue) on both the template and the wood, put superglue onto the masking tape and that way you have a solid fixed template, without any residue.

@mickleblade 8 жыл бұрын

+Dean Grove interesting idea, I might try that, but there's masking tape and then there's masking tape. I've had varying results with the stuff in decorating projects

@robertcornelius3514 8 жыл бұрын

Just an idea, but if you do have to go against the grain, then I would add thin ca glue to that area of the work piece. I have to try this.

@robertcornelius3514 8 жыл бұрын

Also, make sure you use a rubber bottom hold down that has a handle on top to push small pieces through the bit. This prevents a "grab" from throwing the piece across the room.

@rodlopez57 6 жыл бұрын

Any particular double tape brand? Which one do you recommend ? Really didactical videoThank you, Rod

@m3rdpwr 8 жыл бұрын

Didn't explain the grooved inside corner where the trim bit won't fit.

@hinduspl 8 жыл бұрын

chiesel?

@grahamcameron7628 4 жыл бұрын

Trace the inside corner with a sharpe pencil. Then, after removing the template use hand tools to finish. Usually a coping saw and sanding.

@m3rdpwr 4 жыл бұрын

@@grahamcameron7628 This was 4 years go, I'm thinking I knew he did it using a chisel, etc. I probably posted it as a nice to mention thing.

@kayleecox3717 3 жыл бұрын

thanks!

@tommybloink 4 жыл бұрын

Can you do this with a piece of wood 1.5" thick?

@shelby50411 6 жыл бұрын

How did you make the template?

@dtrachtman 2 жыл бұрын

What speed should the router run at?

@hinduspl 8 жыл бұрын

I dont f...... get this whole thing with grain direction.. I know what they're saying but I always have problem with figureout in what direction this grain really is.. any advices?

@robertcornelius3514 8 жыл бұрын

It's easy. Just use your finger nail to dig in to the wood. Then mark an arrow using a pencil. Hope this helps.

@JoeC1977 6 жыл бұрын

Here's what I got out of it - you want to route from a straight edge (going with the grain) to a non-straight edge (one going not with the grain).