The slow swaying of the drone seems to me like undercorrecting. You need a higher P and I value, increase it until the drone starts to sway faster, then use the D value to make it correct before it even reaches the goal so it doesn't have too much rotational momentum when it gets there.

Ok... so your flight controller should be fine. However on the flysky remote hold down the “ok” button to get in to the menu. Then go into the functions setup. The from there setup the Subtrim. If the drone goes the the left then adjust the trim in there. Also go I to your configurator and see where the channels are. If they are off center set up your end points. Just KZfaq that there are many tutorials. In the same menu check out the throttle curve. Since you said it was accelerating fast mess around with you throttle curve. Also check out Joshua Bardwells how to build a drone series. He walks through how to calibrate and keep the drone balanced. His example is with a five inch but should be the same for 5 feet. Definitely watch some trouble shooting videos too. Drones are a very complicated thing. Make sure to watch a lot of videos. The same concepts apply to any size drone. And make sure to hold cancel on the remote to save. Good luck!

Make a “jet pack” with your edfs that makes you run faster

Hey man great video! The drifting could be due to the fact that the drone is so massive. Each propeller is moving massive amounts of air and that air can bounce off of the ground and create unstable air (Essentially creating turbulence). It’s kinda like the ground effect in aviation (but not really bc that deals with heat and other factors). The drifting could also be due to the flight controller. DJI’s flight controllers use the round GPS module to calculate the exact position of the drone, and make it makes small adjustments to keep the drone in the same place. If there are trees above the drone obstructing the connection from the satellites that could cause false corrections. I suggest heading back out to the field and attempting to fly at a higher altitude to remove the chance of the ground effect kicking in. As always stay safe and be careful. Again, amazing video. I can’t wait to see you take off!

can you make a upgrade version of your iron-man suit?

You might need a sensor that detects how the drone is oriented and tell the drone to auto correct the balance issue.

Very cool, can't wait to see the end result

Even though it's low tech, I think u should try making a flintlock pistol

Do the drone projectors from far from home. But have it possible so more than one drones can create the hologram.

0:54 I'm confused is this a "Smart glasses" with holographic display or tony stark glasses? which it is bulletproof and holographic. I'm just thinking of glasses right now

JLaservideo : I'm going to make a "building your ideas" video! Grian: Am I a joke to you?

I know a decent amount about this stuff what I would do is replace the flight controller with a beta flight board. And your flysky isn’t broken when you get the beta flight board u can make adjustments to fix that. Also I would fly it in angle mode so it flys more stable and you don’t have to correct it as much.

Propeller DID NOT LIKE THAT : ejected it's self~ feature 🤣 I'm so dead

Look into changing the software to iNAV. It is not for acrobatic drones is more for dji style cruising

Make a mind controlled headset with an EEG chip and an arduino I am currently working on one and I think it will be cool 😎

The advanced Lazer that you used in the last video, find a way to mount that thing on you, try and make it voice activated or some way to make commands easily. It's like Ironman with his darts, because it has that locking system.

Do you know those cartoon hats with propellers on them? So basically you should make that hat fly.

I think you should adjust the PID loop of your Flight Controller. There's a P, an I and a D value that you can change. If you can't do that with your Flight Controller you should probably get a new one (f4?). The PID loop is the key of every stable Drone and is different on every Drone. Here is a good Video that explains the PID loop: kzfaq.info/get/bejne/gKyEfZWEuJrcqXU.html I hope I could help you!

I build a lot of custom fpv racing drones. If you use a newer flight controller (f4 or better) the firmware is amazing now. I recommend betaflight (firmware). There is a ton of info on youtube for how to set up the flight controller, and tune your pid's. Boards are cheap too, you could get something in the $25-$40 range that would be great. Your old FC is a problem, maybe not your only one, but it really could be that simple. You can move that one or two clicks to be centered on your remote, but likely you need to configure your endpoints in your remote. In betaflight you can set up some slack in your reciever input, it's called "deadband" (if you are contantly seeing it move 1 or 2 or 5 points, even without you touching the sticks).BTW those wooden blades are a deathtrap, plz don't die. I love your videos!

It looked to me like the motors are fighting each other. This could be due to a software malfunction that tries to orient the drone level, but you would need a program like that to have the malfunction. It could also be due to different voltages being run through the motors to speed up and slow down the fans to keep the thing level. This along with possible control malfunctions could be the cause of the motors fighting each other.

Build a powered suit. Use 6 raspberrypi 4's (pi4) joined as a supercluster to power the technology in the helmet, each arm, and each leg respectively with the power of one pi4 to act as the monitor for each appendages personal pi4 check out superhero armory here on KZfaq for an idea of what I'm talking about. Keep up these amazing projects Jlaservideo.

Could you make the hidden extending gun from Sherlock with Robert downie Jr Moriarty

I think you must u might want to try gyroscopes. Those help with stability. Double propellers may help with lift issues and stalling.

Using a pixhawk will be more preferred . They got a good firmware there. Your props. Use carbon fibre. It looks like it's heavy so it's less responsive to the controller's output

Take a DJI Mavic pro system. Im sure you can make good use of it's GPS and stabilization technology.

Could u make a laser attachment for smartphone. The market ones cost around 100$-200$

Use some ultrasound sensors to check if all four corners are the same distance from the ground and correct them depending on the values read

Do you have a gps on it? If not, you should have a gps stabilizer it would stop the lateral movement and yaw. If you want plug n play, go with the Eagle Tree Vector, super easy to set up.

I guess that there are too low PID values , but you need to check if controller values doesn’t jump too much then you connect to pc if they are at 1497-1503 it shouldn’t make such a big vobles. So try to rise P value and test few times with different numbers

Get a taranis QX7("budget") or a futaba t16/t18(expensive but good) or a spektrum ix12(also expensve but good) depends of what protocol you want. Do some research and find something better than a flysky please. also if youre willing try to tune the flight controller to prevent overcorrection.

The moters can be put on a Dihedral angel to self stabilise the aircraft and ensure that as much weight is at the bottom of the aircraft to lower it's centre of gravity you will have a much more stable aircraft.

First increase the normal gains to make the drone stable, then increase Gps gains so it doesn't drift away. Don't increase the gain to much because then your drone will start over reacting/resonating.

How much does your drone weigh? If it's less than 55 pounds you're in good shape. Secondly, I would highly recommend getting a higher quality controller such as the spektrum DX6i or equivalent. Also, a good flight controller that will make your life very easy is getting a pixhawk autopilot. A good ground control software for it is qgroundcontrol. This will let you do a lot of fun things as well as incorporate autonomous capabilities.

Perhaps it needs more weight as the motors are lifting it to easily ? If you put an even balance of another 50 kgs on the frame the sensors will feel it more it wouldn’t harm to try

Also hovering low to the ground will cause it to sway because all the air it’s blowing to the ground will shoot back up and move the drone around. I personally moved away from flysky and went to FrSky but that’s just personal opinion, I got too used to the i6 controller that the better gimbals in my QX7 radio felt weird to me at first. Newer flight controllers like an F7 which have dual gyros make a steadier flight. But on a drone that large I’m not so sure an F7 is something you’d want to put on it, more for the five inch drones for FPV freestyle but I may be wrong.

For anyone that is confused he's making the E.D.I.T.H. glasses from spiderman far from home

Hey add a gyro sphere like how it's used on phones and helicopters. It should stabilize itself man

good video. try a Kevlar/ fiberglass suit with night vision like the one in in Spider Man Far From Home. That would be noice

Make a hidden belde from assassins creed!

Install more crash guards and maybe bigger engines?

You should make smart glasses using the tinyest projecter on the market

It’ll be so amazing if you can make a Gitana that’s motor powered. Thank you.😅

Great video. The coolest vtol I think at the moment is the Blackfly check it out maybe they could help with flight control and design. Again I’m going to ask you to make the same thing as I asked last time. Flying wings using 2 motors as assistants for flapping like the Smeets guy which will work just stronger motors and a guy like you. Build it and u will build one and we can fly highhhh

Ask Michel reves to program it

Jake, great video as always! It would be wise to master the basics of hovering with a 20$ banggood drone with no gps-positioning hold and no barometer altitude-hold, because if the gps glitches on the human drone, u can switch to manual mode and regain control of it.. mark a square box on the floor with tape, and try to hover it 50cm high and as stationary as possible right in the middle of that square area. If you can keep it still for the entire battery pack, then you have nailed it. I used this method to learn inverted hover for an rc heli /watch?v=yww4ceFc6BM

Try to incorporate at least 3 degree of diedro to the motors it will become a lot more stable.

Oh, I hope so much, that the video with the glasses are close to a finish... Because, well. Because I wanna see it. Please tell me it is only... A half hour and then you are uploading it.

Are you going to make E.D.I.T.H. ( Even Dead, I’m The Hero) from Spider-Man Far From Home?

I can tell you have some kind of gps controller so take it off Manuel and turn it to auto level. And you will still be able to control it but it will not bank like over 30 degrees.

You should probably make the frame into a square so then one side is not heavy.

Hi, im building my own drone project and i watched your video series to help me. im getting pretty far and wanted to know where you got those propellers from? i need 18 inch props and i cant find anywhere that sells CW and CCW as a pair, where did you get yours?

You need to get a better speed controller and get someone who knows what they are doing to help you with it. So it operates at the same speed for each motor.

Did you have discord? I think if wenn can Talk its easyer for me to help. I had the Same Problems whith my Flysky, But i fixed it. The pids arent tuned right. (Sry for my englisch im german)

You could build a reallife Ironman Repulsor

SEHOUIGSHDIGB HUISBGDFUI BROOO IM SO FREAKING DONE, THAT SCENE AT 1:55 xDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDD THAT WAS SO GOOD BRO

i always watch "flying kyxz" and his drones have more than 10 motors. two on 2 corners, one fancing up and one facing down plus 4 more in the middle with the same design of one up one down. i think having more will help with balance.

It would be cool to see you make something with hoverboards

Go in the flight controller software to calibrate it

Tilt each motor 5 deg to the center of the craft. It's unstable because it's falling off the edge of the air stream. By slitting the air stream out at an angle a bit you'll have farther to go to fall off it.

Can you make like an Ironman or Edith HUD that’s interactive

Could you make a tiny mechanical spider with a camera I wanna keep an eye on my left sock

You need a really good flight control system for manned flight

test the PID modification on your little quad and apply on the biggest one

Do you have air mode on, it should compensate for any odd movements.

Pls try and make Brixton’s ai from Hobbs and shaw like so jlaser can see

Add 4 more propeller nd motor on the downside also to get perfect balance to a drone

Lmao make a statue that tells time, and blows pure vegetable glycerin out of its mouth and yells 420 BLAZE IT every time it turns 4:20 o'clock

The default PID tuning of the flight controller probably needs adjusting, as it is probably not by default, expecting to be controlling a drone of this size!

Late to seeing this. Amazing and beautiful job. Congratulations on the flight. Did you stop on making a man drone ?

Hey dude you should definetly try building a small drone before a big one

install gps and gyro on it

If you have the code, maybe you can round the values of the input from the controller to make up for the margin of error. Make it so that if the input from the controller is close to center, it'll send 0 as an input to the drone.

Do you have links for the motors and escs?

Try a new transmitter and a new receiver

This is a stupid idea but you should make a drone disguised as a household object.

Awesome video!! xoxo

Try having a weighted object where you would be sitting. Where the weights are being carried now you are lowering the center of mass and increasing the lift you need to generate. I think anyways idk im a cart pusher :P

Hey! First great job man! Second, I am not sure about your settings, but are you using the GPS feature of the DJI Naza? Moreover, are you using the GPS self-balance mode, I am not sure but I feel you are flying it in acro mode, just make sure it is in self-balance mode and for the drifting use the GPS, make sure the GPS is elevated from your metal frame since it can interfere. I have somehow a good experience with drones, so don't hesitate to contact me if you need any help.

Have you calibrated the cg

Definitely upgrade your flight controller. Any F4 should do (i reccommend joshua bardwell f4 flight controller) with betaflight 4.0 loaded firmware. Flight control tech was much different 5 years ago and its the f4/f7 perform way better for the price youre paying

prop disintegrated at the 5:25 mark

You should make an RC spider

What kind of motors are those?

Rocket punch gauntlets: position 3 co2 cartridges or hobby rocket engines on specialized pair of gauntlets in a triad configuration at the end of the forearm close to the elbow that are activated using buttons on the designated hand you want to punch with. Make it to where the propulsion system is attached and built in, or if using co2 cartriges or hobby rockets, replaceable. Ant man has buttons on his gloves so he can shrink down to ant proportions, so same idea but with knuckle dusters and wrist supports to prevent hands and wrists from breaking upon impact of any surface. Call them "Falcon gauntlets"

Yooo make a test with 300 of 12 volt battery!!!! Put them all together and at the end from one side connect it to a copper needle and also on the other,and put the two copper needle together

I had that v2 also and it would randomly crash, I thought I might of damaged the compass or something. Anyway I just gave up on it as it’s old technology.

Fire saber not light saber

Look up Para motors the could help you design and control and make it

Well done ❤️❤️❤️❤️

Not exactly an expert but check out the cc3d controller is what I have for my own bad drone project. When it got it it was light years better than the garbage hobby king one I had. The cc3d has lots of settings you can change on the computer to try and get it to help fly stable more. Also with the controller you can usually set trims (I think its trims i forgot) so that its always a little to a direction. You can do this to help fix any offsets, like if it always leans one way trim it to haev a bit more to that counbter that side. But generally if its leaning you might have a balance issue or something. My drone is just a 3d printing project but my printer is old and junk and im lazy and take too long to design new parts in fusion360 so its taking years lol. My motivation is pretty low every time I do anything with it something goes wrong or breaks. Repeat. Best of luck super cool project look forward to next vid.

Maybe if the motors were out further on the arms it be more stable.

Can you try to make the umbrella from kingsman

Build a working Fatman from Fallout with a working nuklear warhead :D

How about a Mini Stealth Boat?

you should make a remote control boat

Build a hotglue gun

like the new intro

or make a cuphead finger gun like you make a very small object and put a colored fire setting and a mode setting like you fill it with different things and it shoots them with different properties

How much weight can it lift@

You should make a 007 James Bond, mini scuba tank