Testing Prius Hybrid battery cell health the easy way

Рет қаралды 5,933

4 ай бұрын

Using a $40 Harbor Freight 12 volt battery tester to test the health of individual cells of my 2008 Toyota Prius battery.
www.harborfreight.com/12v-dig...

Пікірлер: 32

@Adzeoda 2 ай бұрын

This is really helpful for future reference....apparently I had all I needed already😂

@kellyfitzpatrick4355 2 ай бұрын

Excellent! I actually gave up after trying to test cells and replaced a battery. I won't do that again!

@dc5duben96 3 ай бұрын

thanks for the info! really helps me out just diving into my battery problems

@venkaeswararveeramachaneni8798 Ай бұрын

thanks for the prompt reply..

@stevenabnoosian2028 2 ай бұрын

That was really helpful Thank you 🙏

@BFKGintaras Ай бұрын

Wow ! Thank you

@alext8828 11 күн бұрын

I saw a video, way back, where they used a regular load tester on a newly assembled battery and went right along checking each module, disregarding polarity. The tester was one of the ones that's box shape w/ all the holes in the front and a meter above that. There was a switch at the bottom and it had short cables with large alligator clamps. HFT $20, I think the type was. 100 amp carbon pile. I'm sure there is no reading of internal resistance but it shows the draw=down over a few seconds. I wanted to know your opinion on all that. Specifically, does internal resistance correlate to voltage draw down?

@venkaeswararveeramachaneni8798 Ай бұрын

car stopped on the road 2 week ago. can the battery be reconditioned ? getting a dual charger/discharger.

@jayviz Ай бұрын

thank you for this great video. What does this device do differently than simply using a multimeter to test resistance?

@cvedeler Ай бұрын

It puts a load on the battery and tests internal resistance. My simple multimeter can only test resistance, but can't even do that with voltage present. .

@jayviz Ай бұрын

@@cvedeler Ahh, I see. Since anyone considering this procedure probably already owns a charging unit, I am wondering if the resistance feature on such battery chargers would work just as well, or are they inferior in some way? I have the SKYRC B6AC for example.

@jayviz 24 күн бұрын

won't the resistance feature on a battery charger measure this just as precisely? I'm guessing if anyone has yanked their battery, they are preparing to charge it with such a charger. My sky RC charger for example can measure resistance. Or is that inferior in some way?

@rayluo4665 24 күн бұрын

Chris, your test method was indeed creative. But are there devices more suitable for this kind of testing? The battery tester you used was originally designed to test the 12v starter battery, not for a 7.2v (nominal) module. Other than worrying about the reading would be inaccurate, I do not know how that "500A cold cranking amp" was tested, and I wouldn't attempt (until I watched your video) to use it, for fearing that it would draw too much amps from the battery module thus potentially damaging it.

@cvedeler 23 күн бұрын

I'm sure there are many deices more suitable, but they are likely more expensive and harder to find. This is cheap, easily available and works well enough to find the bad cells. I was a little worried about the fact the device is for 12 volt batteries and not 8 volts. But it turned out working anyway. Lower voltage is probably less a concern to higher voltage. Accuracy isn't the goal, but rather finding the cells that may show adequate voltage but fail under load. Such a small device can't possibly draw 500 amps so I wasn't too worried about that.

@waqarbokhari675 10 күн бұрын

I used the onwei tester and it come out as all the modules are bad. It also give you an option to choose the kind of battery, like agm, lithium and 4 others. Resistance was around 5.4 and 6 all across. I don't think this really work good for hybrid battery module.

@e.g.5385 5 күн бұрын

When you replaced the bad module, did you have high voltage difference compared to the other modules? I replaced a module and showing 1.2 voltage difference and throws the "check hybrid system" p0a80 code on my odb2 reader. I need help.

@cvedeler 4 күн бұрын

The voltage of the cells wasn't my problem. All my cells were +/- less than 1 volt. It was the internal resistance that caused my problem.

@adrianleighuk 2 ай бұрын

A question. Once reassembled did this help resolve the issue and if so in your experience what was the best internal resistance as a guide? Thanks for the video. A great idea by the way.

@cvedeler 2 ай бұрын

It worked well. I had one terrible cell, but ended up replacing 5 others that were questionable.

@juanvaldes1837 Ай бұрын

@@cvedelervery helpful thanks a lot

@anhtoan19 2 ай бұрын

Can I send it to Japan?

@venkaeswararveeramachaneni8798 Ай бұрын

i used the tester you used. results voltage abovr 7.55 all cells resistance 5.00 milli ohms, all 100 healthy. but says all cell have zero charge left. what is the solution.how to charge ?

@cvedeler Ай бұрын

7.55 volts is too low. They should be closer to 8 volts. My lowest voltage cell was 7.71. If the cell resistance is 5.0 but the voltage is low, that points to a different issue, possibly with the charging system. Good luck!

@sleepydo6463 2 ай бұрын

silly question but is the 2012 Prius battery same layout?

@cvedeler 2 ай бұрын

I believe it is similar.

@mattaitchey4917 Ай бұрын

2012 will have "low ir" modules, so this ir based test method wont be any use to you

@MervsServiceSecrets 24 күн бұрын

@@mattaitchey4917 I wondered about that as well. For anybody that has monitored resistance using the simple dr prius app, 19 to 20 milliohms is pretty common. Yet in this video, he rejects the one with 17 milliohms as being bad.

@mattaitchey4917 24 күн бұрын

@@MervsServiceSecrets would have been a better module than the others!

@MervsServiceSecrets 23 күн бұрын

@@mattaitchey4917 I don't think I've ever seen a module with a resistance of 5!