The AlternatorGenerator, First Attempt. 48V Battery Charging

Рет қаралды 1,592,548

Күн бұрын

Will this even work? 48V alternators are expensive. Can we make one from a standard 12V car alternator? I don't know, which is why I decided to try. This video a a complete walk-though, start to finish.
I bought a 12V car alternator off of craigslist for $100. I wasn't looking for any specific model, but I wanted a serpentine pulley on the alternator, and it had to look decent. Next was a Predator gas engine from Harbor Freight. In this case, I purchased the 224cc MAX engine, which is 6.6hp. The 212cc 6.5hp engine would have also worked well for this build.
The goal is to make a dedicated generator that can recharge my 48V battery bank. I'm using the EG4 LiFePO4 batteries, which is a little more than 30kWh. Sometimes, during the winter, the solar production doesn't keep up with my loads. That's when I need to supplement my solar with some generator run-time in order to recharge my battery bank. Yes, 48V generators exist on the market, but they are thousands of dollars. I built this generator for about $400.
Intro: 00:00
Theory of Operation: 00:43
Parts Used: 04:44
Alternator Wiring: 07:04
Building the Base: 16:43
Drive Pulley Installation: 21:05
Wiring the Busbars, Rectifiers, Buck Converter, and Capacitor: 27:45
Test Run: 38:29
Conclusion: 44:20
Amazon affiliate Links:
Hydraulic Crimping Tool Set, Temco: amzn.to/3JZmzkv
Ratcheting Crimping Tool: amzn.to/3ZnipZm
Full Bridge Rectifier: amzn.to/3nvZ0In
Heat Sink, Aluminum: amzn.to/40uxCZQ
Thermal Paste: amzn.to/3FZ36yX
Ring Terminals, UL, Marine: amzn.to/3K0N3lw
Capacitor, 450V, 1000uF: amzn.to/3lTHopw
DC to DC Buck Converter, 12V 5A: amzn.to/3nug0yK
Charge Controller used in this video (Victron 250/100): amzn.to/40k4kNz
Less Expensive Charge Controller: amzn.to/3K4fZJE
Engine Hour Meter and Tachometer: amzn.to/3KhxMhE
Vibration Engine Mounts: amzn.to/3nmbbaz
Rubber Feet: amzn.to/40DKsoq
Nuts, Flanged, Nylon insert: amzn.to/3ZrVMD4
Busbar set: amzn.to/3M4plYq
Circuit Breaker: amzn.to/3M3N1w6
Center Punch: amzn.to/42Q5EJH
Tachometer, Digital: amzn.to/3Kl1ken
Tesa Tape, for looming wires together: amzn.to/3TXUrTx
Electrical Tape: amzn.to/3KkdeVJ
Kapton Tape: amzn.to/3G2VWKe
Loctite, Blue 242: amzn.to/3zhO6IL
Bandsaw Blade, metal cutting: amzn.to/3M3yro1
Pulley, serpentine belt, 3/4" bore: amzn.to/3UaXuYF
Serpentine Belt: amzn.to/3zlsATu
Pulley installation kit, power steering pump: amzn.to/3JUeopz
Tap Magic cutting oil: amzn.to/42PruwW
Dewalt Step Drill Bit: amzn.to/3G5DwZj
Break-in Oil for Engine: amzn.to/3nzCG0J
Soldering Iron, Large: amzn.to/42QY0i6
Solder Wire, Rosin Core: amzn.to/3Zvh6aC
Flux Pen: amzn.to/40qeLPC
Wire, Silicone, 12 gauge AWG, flexible, tinned: amzn.to/3zonJRq
Wire, Silicone, 8 gauge AWG, flexible, tinned: amzn.to/3zlkg6u
Pen, deep reach marker: amzn.to/3M3PKp7
OIl to protect metal, Ballistol: amzn.to/3KlZt8Q
Heat shrink tubing, marine, 3:1 amzn.to/3zC7NeR
“As an Amazon Associate I earn from qualifying purchases.”
Harbor Freight Links, Not Affiliated:
6.6 Hp, 224cc, MAX: www.harborfreight.com/generat...
Band Saw: www.harborfreight.com/power-t...
Tap and Die Set, SAE, Titanium: www.harborfreight.com/titaniu...
Note: I have no affiliate with Harbor Freight.
Previous Video making a battery charging generator from a free treadmill motor: • DIY DC Generator: char...
Signature Solar Affiliate Links:
Battery Bank, EG4-LifePower4, Lithium, 30.72kWh: signaturesolar.com/eg4-lifepo...
Inverter kit, Schneider XW PRO 6848: signaturesolar.com/bndl-ac-co...
Chargeverter: signaturesolar.com/eg4-charge...
Disclaimer:
My videos are in no way intended to be instructional "how-to" lessons. I am simply documenting my project for informational purposes. Property damage, personal injury, or death may result, even when following manufacturer's instructions. I cannot be held liable for such damage or injury. It is YOUR OBLIGATION to ensure that you are complying with any local and federal laws as well as code and permit requirements.
David Poz, LLC

Пікірлер: 3 000

@DavidPozEnergy Жыл бұрын

Part 2 Video is out: kzfaq.info/get/bejne/md9gp5ei1p7Rg2Q.html It includes a fuel economy test, thermal imaging, vibration fix, and I answer your questions.

@Mike80528 11 ай бұрын

Be careful with that circuit breaker. I didn't see a DC rating and high current DC circuits can be a lot harder to trip than AC (have been known to cause issued with solar...)

@jackoneil3933 8 ай бұрын

Thanks David! Very interesting and informative test. I just watched your follow-up video and in Alaska connected the exhaust of air and water cooled generators to a coil stainless steel and copper tubing, and immersed the coil as crude stack robber and estimated I was able to recover up to about 20% of the thermal heat energy from the engine. I mounted the generators above the heat exchanger coil inlet and plumbed the outlet out the bottom of a spray-foam insulated fiberglass or steel tanks so the exhaust condensate would drain out. On water cooled generators from 7kw to 600kw we installed coolant heat exchangers to the engine coolant system, removed the engine thermostats and used AMOT valves (Thermostats) in the heat exchanger loop to maximize heat recovery. Combing engine heat recovery with commercial exhaust to water stack robbers recovered up to 60% of the engine heat, so basically the fuel cost of our electric load provided heat most of our space heating. I was thinking a heat recovery might project might be interesting for viewers, and I would be happy to provide insights from my experience if needed.

@Thunderstormworld 8 ай бұрын

The best generator I built 15 years ago , consist of a 200cc gasoline engine and a 12 volt alternator and a 12 volt 647 battery and a 1000watt inverter. What makes it extremely better than a normal generator mine can run 2 hours without needing to start the engine so instead of running a normal generator for 4 hours on fuel it use only half , couple this that it's connected to solar panels , my next aim is connecting to a wind turbine .

@dodgeme1986truck 8 ай бұрын

Add a heavy flywheel to the engine as it will stabilize engine power pulses allowing less vibration and more/stable power production

@1crazypj 7 ай бұрын

@@dodgeme1986truck A single cylinder industrial engine without balance shafts is always going to vibrate pretty bad

@D2O2 Жыл бұрын

Great video David! Some suggestions, rigid mount the engine and alternator together on one frame, then iso mount that frame to your platform. This will help maintain proper belt tension and reduce overall displacement and vibration.

@Jody_VE5SAR Жыл бұрын

I second this idea. As it is now, the dynamic response of the engine mounts can cause slack in the belt at various resonant frequencies. A fixed relationship between the engine and alternator would solve this (either still using a belt, or via direct drive). Also - just a thought - it might be possible to use the motor's magneto to provide the necessary kick-start to the buck supply.

@chrisw6690 Жыл бұрын

I also agree. As it is now the belt tension is side loading the isolators to the point they probably aren't very effective and will fail after a while. Even in a vehicle the alternator is bolted directly to engine (yes their maybe brackets but no isolators) and then entire engine assembly is on motor mounts(isolators). But otherwise I thought this was an awesome video.

@-Gadget- Жыл бұрын

Good idea, but then build an open frame/box that is slightly bigger than the whole unit, and suspend the entire unit within the cage/box with bungy cord or springs. Springs should theoretically remove 100%of the vibrations before it even gets to the frame/box 🤔

@jwray9799 Жыл бұрын

I replied the same fix too,, before I saw yours ///perfect idea!

@barrellcooper6490 Жыл бұрын

This was my first observation too. Motor and alternator need to be rigidly joined so the belt can function under constant tension.

@TrackGeeks Жыл бұрын

This is one of my favorite projects you've done so far.

@DavidPozEnergy Жыл бұрын

Thank you. It was a lot of fun to build.

@TrackGeeks Жыл бұрын

I appreciate the effort and tenacity you displayed to get it working.

@mukhtarosman2492 Жыл бұрын

@@DavidPozEnergy hello mr david i intrested u re vedios i am in somalia i want to use 24v by car alternative is that posible?

@jmacd8817 Жыл бұрын

@@mukhtarosman2492 your best bet would be an old military alternator, as most military trucks run at 24 volts. It's also possible to find an older diesel truck alternator, as they used to be 24 volts, but not mostly use 12. This would simplify your setup, because you could use the alternator "as is" without having to modify it. Google could help you find what make, model, etc of alternator to look for.

@Swampwild1 8 ай бұрын

Fascinating project. Made me look at what you can buy for this because I’m not anywhere close to skill level for trying even with your excellent and entertaining video.

@spkay31 9 ай бұрын

"David - I'm not an electrical engineer - Poz". Well I have 2 degrees in EE and you sir are one hell of an imposter! Seriously great work all around. Love the combination of electrical, mechanical, carpentry and general problem solving skills to pull off a reasonably challenging project and produce excellent results.

@DavidPozEnergy 9 ай бұрын

Thank you, that's one heck of a compliment. I appreciate that.

@habeelkhan6532 Ай бұрын

@@Willam_J Engineer never retired 😂

@kingi7607 Жыл бұрын

i wasnt expecting it to output a whole 3kW, thats awesome. fuel consumption tests at different loads would be interesting to see.

@Razza2250 Жыл бұрын

Great idea. Great execution! My advice on belt vs direct drive would be to leave it as is. The alternator is turning at a good RPM for sufficient cooling while staying well within its design limits for RPM. Running it slow is going to mean less airflow over the stators and therefore more heat and lower efficiency. I also think you might be hitting the limit of the motor here more than the alternator. The MPPT won't load up the alternator any further as the RPMs fall, its going to find the sweet spot where the motor output is limited by its torque. You might be able to get a little more out of it, but honestly, the limit here is efficiency. A typical alternator is around 50-60% efficient. Being generous, that means 3kW out requires 5kW in from the motor in the form of mechanical input. A predator 212cc is a 6.5hp engine, which is 4.85kW. That's about bang on for what you can expect this motor to give and, as you observed, she was a-strugglin'! The alternator is rated by its current, so if you're pulling 120A from it, the voltage is not important as the heat generated in the stator is defined by P=I^2 x R. You would need a much more powerful motor to bring this alternator anywhere near its limits (around 12hp would be about right), but then you would still have that low efficiency of the car alternator ruining your litres to kWh ratio. Still, this is an amazing and cost effective innovation and I've been stewing on this idea for ages wondering if it could work. Bravo dude

@JbVest Жыл бұрын

would you have any input on how to wire an alt with 3 separate windings?, its not in the wye config it was wired in the delta config instead, what was weird to me is that there was only 8 diodes on the rectifier

@buddyrojek9417 Жыл бұрын

I run a similar setup using a bigger motor but I run it on charcoal gas so I have zero running costs

@gta-6837 Жыл бұрын

Your comment was insightful

@dougbas3980 5 ай бұрын

I would think the alternator is rated 3kW only for a short time before heating would be harmful to the alternator. A long run at high out put with testing alternator temp would be interesting.

@neiloconnell2120 Жыл бұрын

David. Very well done. I am impressed with your skill set. Great video.

@DonKees Жыл бұрын

Hi David, I really enjoyed the video. You mentioned raising the 12VDC input from the buck converter into the rotor. I would advise to measure the rotor current and increase slowly and carefully since it may not actually increase your output power as you were already getting the rated output power for the alternator. The rotor winding will magnetically saturate and then the extra current will only overheat the rotor and it may be damaged as the wire gauge is really small. Kind regards.

@kennethdegruchy5503 Ай бұрын

The source of 12 volts for the field is constant however in the actual automotive application I believe the field current is duty cycled from the voltage regulator dependent upon the total load. The point is you are maxing out the field so I wouild not think it a good idea to raise the field voltage/current any further to avoid over heating the field winding.

@ralphmersdorf1098 2 ай бұрын

I was doing something scary this one time and wasn't sure what I was doing, faked it. But when I finished and tested it and it worked I was like hey it worked. The customer was standing behind me and I didn't know, but he was cool and was laughing and high 5 me with a smile. What a relief.

@LithiumSolar Жыл бұрын

Wow, very interesting build. I thought it would work but didn't expect over 3000W! Not sure how, but definitely need to secure that pupper down as it was starting to walk away lol.

@DavidPozEnergy Жыл бұрын

Thanks Lithium Solar. Yes, I was surprised. I was hoping for 1600W. I came to that number because when I built the treadmill generator, I used a 3hp engine and got 800W. I figured double the engine, double the power out. So, this blew my mind. I had to record my conclusion over and over again because I was so giddy. LOL

@Michael-rz7ic Жыл бұрын

Wow, what a fun project. Thank you so much for the theoretical walk-through before the build. Now how bout some type of diesel engine with that alternator? Maybe off the pto of a small tractor, or an old John Deere diesel garden tractor??? Could be a lot of fun.

@jonasstahl9826 Жыл бұрын

I would be careful to not overheat the alternator, they are not meant to produce there full power over extended periods of time.

@whatta7793 Жыл бұрын

Same, I knew it would work, but I was expecting maybe 1500 watts give or take. But 3000?!?! That shocked me greatly. I know alternator sizes vary from car to car, but for example, my 1999 Tahoe has a 105 amp alternator, charges at 14.8 volts when I first start it, and drops to 14.4 volts after everything warms up. That's where I got my 1500 watts give or take figure, but this little puppy done over 3000 watts!

@russ22f Жыл бұрын

Fantastic. A fuel efficiency test comparison with your other generators would be great. I thought the pully would be too large to start the alternator charging on under load. I think the lower torque curve of the engine had to help in that regard. Very enjoyable video to watch.

@rbartsch Жыл бұрын

I'd really like to see a fuel economy test! ❤

@alwaysbadideas Жыл бұрын

I think this is going to be lower efficiency in general because alternators use some of the energy to self excite. Generators have permanent magnets which distinguishes them from alternators.

@M35a2guy Жыл бұрын

I would love to see the comparison vs the Big honda and the little one you rented. Interested to see how they stack up.

@JbVest Жыл бұрын

@@alwaysbadideas mine pulls about 25-30 watts to excite the rotor enough to make some good power. 2.4kw

@dantronics1682 Жыл бұрын

@@alwaysbadideas the advantage with alternator is you can keep the output voltage stable at any speed where a genarator have a mean curve.

@waynesharp1690 5 ай бұрын

Stumbled upon this video and watched the whole thing. Really enjoyed watching. Thanks 👍

@stevesawyer6377 2 ай бұрын

As usual, great video. Always appreciate the depth of your information and how well you explain everything

@lbroome Жыл бұрын

A few nice things to see would be the temperature of the alternator and the charge controller at full load for extended periods, and the amount of ripple in the DC to the charge controller.

@rickrussell Жыл бұрын

Yeah I'm really wanting to see an oscilloscope hooked to the various outputs.

@peterryan7340 Жыл бұрын

I would love to see a thermal view of various components during running at various rpms.

@onedayatatime723 Жыл бұрын

rpm *

@glennimmortal Жыл бұрын

@@onedayatatime723 rpms's

@QuackGoesTheDuckQuackQuackQuac Жыл бұрын

@@glennimmortal rpmses

@AutodidactEngineer Жыл бұрын

@@QuackGoesTheDuckQuackQuackQuac rpsexe

@edwinpagan4705 Ай бұрын

My dude. You are amazing!!!! Nice build!!! And making that adapter for the pulley install. Big props

@richardbilous5338 Жыл бұрын

You've always been great at teaching! I miss ya so much! Thanks David & the fams for everything you've done for me! Even though it was many years ago I still remember those days as a kid watching ya do your projects! I'm glad your still doing your thing!

@CSEV661 Жыл бұрын

I would love to see a fuel economy test on this one. I know I'm not the only one that's been looking into making something like this.

@JbVest Жыл бұрын

Yep I know I certainly have been wanting to make something like this for my two giant 48 volt packs I built. It would just be a nice backup to the backup. Redundancy baby!! 😂

@FraLin Жыл бұрын

it will be a Desaster below 50,%

@urieaaron Жыл бұрын

Even though I will probably never build something like this project, just one thing all by itself made it well worth my time. Watching you build your own adapter with little more than a drill press, a file and a tap was a learning experience and inspiring.

@DavidPozEnergy Жыл бұрын

Yeah, that was fun. It was about midnight, and the stores were closed. Not that I could have bought an adapter even if they were open, LOL.

@blakeburgess7171 Жыл бұрын

I've been using waste vegetable oil for years, my standard ratio is 4 gallons waste vegetable oil to one gallon of gas, I have a 1982 Isuzu imark diesel engine that I've put in 3 different cars, I have saved over 50k $ in the last twenty years in fuel costs, this past winter I've started using a 5kw diesel heater with the same formula of fuel, it done a great job saving me money on my fuel bill, me and you have similar goals (off grid) I can buy a small diesel engine on Amazon for around $275, I don't know how compatible it would be with my fuel formula, I might need to tweak it some, or I was thinking I could just run my car to charge batteries, any suggestions would be greatly appreciated, I'm clueless to electrical and solar systems

@blakeburgess7171 Жыл бұрын

I work in a restaurant and I have unlimited supply to waste oil

@1982MCI Жыл бұрын

@@blakeburgess7171 and I was just going to ask you where you were sourcing that much waste oil at but you read my mind! Thank you Blake

@cannaroe1213 5 ай бұрын

@@blakeburgess7171There are two issues with bio-diesels, can the injection system handle it, and can the rubber/plastic parts in the fuel system handle it. Older cars typically answer yes to both. Newer cars depends, the limiting factor is usually the injectors, the rubber parts take a year or so to degrade if not correct. lots of videos on youtube about it

@charleyevans2811 6 ай бұрын

I really enjoyed your video. As an 1st yr electrical apprentice, this video really helped me to understand things I haven't see on the job

@lawrenceengel3330 3 ай бұрын

This is a fantastic and interesting project build, well done 👌

@remix381 Жыл бұрын

I have been watching your channel for sometime now and find your projects to be very educational. Thanks for the great content!!

@rklauco Жыл бұрын

When this started, I thought this will never work. Yet, it not only did, but did beautifully. Congrats!

@taylorboarman7993 6 ай бұрын

Your a genius, would love to watch more alternator builds.

@geetootiger5418 Жыл бұрын

Nice setup and your electronic knowledge is amazing! The reason for the slack in your drivebelt is that the alternator is fixed to the baseplate, while the motor can move in its rubber mounts. You should install both the alternator and the motor on a metal plate or frame and then connect the whole assembly with rubber mounts to the base plate.

@cartmanrlsusall Жыл бұрын

That sounds very reasonable

@ericdelevinquiere9902 Жыл бұрын

would love to see if this alternator can keep its output at 3 kw for several hours without burning up. That would be significant!

@walsakaluk4630 Жыл бұрын

Of course it will. The stator is rated at 250A.

@ericdelevinquiere9902 Жыл бұрын

@@walsakaluk4630 still like to see it, seen too many burn out with way less amperage going thru especially when placed in continuous high load with poor cooling situations.

@mk-en9fj Жыл бұрын

I was thinking the same thing. Every regular automotive alternator I've seen has gotten very hot when running at the high end of it's rating. Most are likely not built for a 100% duty cycle at maximum load. Must test it and keep an eye on temperatures, including the diode pack.

@pieterbezuidenhout2741 Жыл бұрын

Alternator is going to overheat especially with Lithium batteries.

@2pist Жыл бұрын

I tried this with a 3 hp Briggs 40 years ago. As soon as I ramped up the field it died. Did you try slowing it down to see the effect on voltage? I'm thinking it wouldn't drop much unloaded. Are you using anything to control the field current? If the charge controller had a feedback loop you would be all set! Running the voltage up is decreasing the current through the windings so heat shouldn't be an issue. I'm happy to see this work. I should do a similar vid but tie it to my inverter and call it a generator. 😊

@DanTheMan0695 9 күн бұрын

As a licensed electrician, I am very intrigued that these little alternators are simple 3 phase motors. I had no idea, and now I will be experimenting with this myself. Also, I have to say; I am very impressed at your cleanliness with your wiring, proper gauges (even when you weren't sure on the output amperage, you anticipated well!) Followed!

@russelljohnson6243 7 ай бұрын

Dude, your children are precious! Thank God for them and pray for them all the time!

@JohnBaker3000 Жыл бұрын

Without a doubt, you keep us geeks very happy! Very cool project!

@samvalentine3206 Жыл бұрын

I'm not sure why this build is so fascinating for me. Probably because I always wanted to do exactly what you did. Good job! You built it based on sound theory and it paid off! It would be interesting to see how much gas it uses at a reasonable charge rate. When you pushed it to 100, that seemed to be too much - then you dropped it to 50. Maybe half way in between? 75? Then see the power output and get an idea on the gasoline usage. Awesome project and thumbs up, David!

@davidrobertson1980 Жыл бұрын

Pretty sure he went to 60 Sam, and when I heard the motor struggle I thought "Nah David, you need to drop it to 50" and he did that exactly and smooth sailing from there.... definitely needed this drop or the motor would overheat being air cooled and efficiency would plummet and wear increase exponentially in the motor.

@domlecompte2415 4 ай бұрын

Your patience and taking the time to explain, deserves a Like & Subscribe

@DavidPozEnergy 4 ай бұрын

Thanks.

@mtnsofutah 4 ай бұрын

Thanks for doing this, I have wanted to do it but I'm too cheap to start throwing money at it. Now I have a good idea of what to purchase for my project with only doing very little experimenting. Great information, thank you again sir.

@user-mp9rd4hg8b Жыл бұрын

I did something very similar a few years ago with a 10 hp diesel engine. I used dual alternators for power and also to charge/recharge a small battery bank for off-grid use. It works very well and is very reliable. Plus I get 10-12 hours of use out of a 3 gallon tank of diesel.

@jerrybabatunde3380 Жыл бұрын

Please can you help me further with yours 10hp diesel engine design. I am thinking of using a bigger alternator for 10 tires dump truck. I really want to be 100% off grid

@jerrybabatunde3380 Жыл бұрын

10 to 12 hours ops from 3 gallon diesel tank is absolutely impressive

@dudeinaroom1238 Жыл бұрын

Nice user name....WTF

@ryankim3612 Жыл бұрын

@@dudeinaroom1238 IKR!?! (I guess he can’t call himself “non-binary”) WAGGA-WAGGA…. I crack myself up!

@timpeterson2738 10 ай бұрын

Use your name buddy.

@unknownuser8885 Жыл бұрын

I've seen in boats where those small frame alternators do not survive well at high duty cycles with near full field output. Particularly with charging large lithium banks where the charge amps remain high for most of the charge cycle as opposed to typical automotive applications where there may be some high initial current but it should taper quickly.. Even some of the large frame alternators that are available get thermally regulated during large charge cycles and or cannot survive at the duty cycle. So if you were to upsize this I would certainly add a regulator or some device to clip field voltage to protect the alternator.

@bawatechreview2168 10 ай бұрын

Thanks for sharing sir. This video clip gives me an idea on how to use the alternator as a wind turnine generator

@williamickes3143 Жыл бұрын

Great job! I'm watching. I'm planning. Keep up the great work! 👍🏼👍🏼

@jpabon18 Жыл бұрын

You took an idea I had and brought it to fruition. With a few mods, it's perfect! You just gained yourself another sub. Do a fuel economy test on it next please. I almost forgot to say, GREAT JOB! 👍

@benw1333 Жыл бұрын

I would remove the vibration isolators(motor Mounts) from the motor and mount the motor and alternator and brackets to a solid rigid piece of steel then install the isolators on the bottom of that main plate to the base plate. This would keep the belt tighter and more stable. i think the sloppy belt was contributing to the roughness especially when under the greater loads. This was such an awesome project and i now have so much more knowledge about the many applications of a automotive alternator! Thanks for creating this video and sharing it David!!

@DavidPozEnergy Жыл бұрын

Thank you for the suggestion, I'll have to try it. I appreciate your kind words. It was a lot of work, and I'm glad you enjoyed it.

@samvalentine3206 Жыл бұрын

This idea of vibration isolation sounds like a good idea - maybe worth testing? Great work! Thanks for the super-interesting project!

@andyfarese5255 10 ай бұрын

truly a great video, your application of the scientific method is sound and this was a very helpful practical demonstration of alternator capabilities

@Jim_One-wl4ke 5 ай бұрын

Awesome ❤ I sure like to try this off grid backup in case there’s no sun. Thanks

@n0ctrnl128 Жыл бұрын

A tensioner pulley would be a great addition. Keep you from having to torque the belt so tight with that bracket and make it MUCH easier to maintain. Also, putting some high(er) tension springs between the engine and the board would absorb some of your vibrations.

@markb3146 Жыл бұрын

I agree on a tensioner but I would source one that is spring loaded.

@kinzieconrad105 Жыл бұрын

Wrong

@DodgyBrothersEngineering Жыл бұрын

Wrong way to go. You are adding to the side load of the mounts.

@justinneill3888 Жыл бұрын

Loved this project! I've always wanted to build something like this. Yes, please do a fuel economy test. Also maybe some data comparing the yield from a DC generator vs your AC generator.

@tomthumb3085 4 ай бұрын

Fantastic build, thanks. Very well designed and executed. I’m subscribed.

@alexanderbinai9583 Жыл бұрын

David excellent of work, self explain.. continue with similar project. I am very interested in this project

@wg6215 Жыл бұрын

Very nice setup. It might be a good idea to mount the engine and alt on a separate platform to isolate the electrical components from the vibrations. They will last much longer, particularly the cap. Also a fuel burn test would be interesting to see. Good luck.

@frankstocker5475 Жыл бұрын

You are every young boy's dream uncle. You proved it works now I see improvement in the drive belt connection & maybe a temperature gauge on the alternator. Well done.

@EBF-oc3ke 16 күн бұрын

Nicely done. Impressive build.

@BruceS42 Жыл бұрын

I got here kind of randomly, never heard of the channel before, but the video title was interesting enough to get me to start. The quality of presentation kept me through the whole thing. Nice work! I've done some builds of my own over the years (I'm 58), and appreciate the work and planning it takes to get something to really work. Thank you.

@DavidPozEnergy Жыл бұрын

Hi Bruce S. Thanks for watching through the video. I appreciate that.

@ShafaqIftikhar-pw9ld 2 ай бұрын

Absolutely beautiful. Detailed video easy to follow. THANKYOU FOR THE UPLOAD!

@DavidPozEnergy 2 ай бұрын

Your welcome. Thanks for watching.

@galen__ Жыл бұрын

Considering all the possible challenges and unknowns when combining multiple items together, I didn’t know what kind of result you would have until the ending. Thank you for sharing this with us.

@dawgrules1 Жыл бұрын

Thanks for the video David, great information ! If you have not yet read it, "OPERATION OF THE LUNDELL CLAWPOLE ALTERNATOR AT HIGH POWER DENSITY AND EFFICIENCY" is a great read on this specific topic. It gets into using large alternators intended for diesel semi tractors and the author shares a ton of valuable information and a little history too.

@johnbrumfield6311 6 ай бұрын

Grea job explaining exactly what to buy and how to build it thank you😊

@davekauffman8727 2 ай бұрын

Your kids are adorable! Looks like a nice project to try building 🙂

@jjohnston7837 Жыл бұрын

Love it! I'd definitely like to see how efficient this rig is.

@jsmith3728 Жыл бұрын

This is genius. Please do more with this

@paulhafner9781 3 ай бұрын

Well done! Congrats on idea to proof!

@uet7417 11 ай бұрын

Wish I saw this before I decided to get into metal casting to make a serpentine pulley with a 20mm bore for my diesel engine... Great video David!

@boxbawks Жыл бұрын

Man, you do the things I've been talking about for several years; which is recycle materials and think outside of the box to get the best out of them. Anyone that builds self sustainability (even if its just working TOWARDS it) is going in the right direction in my book! SUD'B!!!

@DormantIdeasNIQ Жыл бұрын

only one problem, the experts who already serve this cooked are in the same thinking, thus reinventing the wheel is not that more efficient, + most people will not engage in this much technical ability... and don't get fooled, he spend a massive amount of time and research before he even attempted this contraption and got advice from experts.

@ryankim3612 Жыл бұрын

@@DormantIdeasNIQ ….you’re prob not that much fun at parties…?

@MHLivestreams Ай бұрын

Agreed. Backyard shed engineering is best. I'm wanting to make a little diesel 12v generator now, maybe with a flywheel, try getting max output from minimum revs. It's easy finding unwanted stuff from people to make things from. Great fun, and satisfying.

@porschmn Жыл бұрын

Adding a idler pulley , like in the cars charging system, to the belt may help the belt tension in your setup. Great build, learned a lot on this build, some of which I'm still trying to assimilate.

@dodgeme1986truck 8 ай бұрын

He should add an additional heavy flywheel to the engine as it uses momentum between engine power stokes to keep the engine spinning this is why it's shaking the shakes are the power pulses a flywheel evens out the pulses keeping the engine rotating at a more steady speed

@jonasduell9953 6 ай бұрын

Idler won't do much, he loses tension with the motor twisting on the rubber mounts. It all needs to go on a steel/alu/extrusion bar frame/base plate then on rubber mounts to the wood to maintain perfect alignment. The way this is built, the pulleys are pulled out of alignment by the belt creating uneven tension and wear on the belt. That thing won't live long...

@Popeyes66 6 ай бұрын

Thanks for carrying out the experiment that I could not afford to do myself Dave .

@pieterviljoen1620 Жыл бұрын

Well done David !

@8546Ken Жыл бұрын

It's possible that the built-in rectifier diodes would have worked. I've heard of people getting 120 VDC from alternators.

@carlgateman6839 Жыл бұрын

You are correct. The built in diodes would be just fine. You just remove the regulator and apply whatever voltage you want to the rotor to get the desired output. You must be careful however not to exceed the current rating of the unit itself.

@CountryGeek-hr8tk 10 ай бұрын

I was puzzled as well, why take out a perfectly good set of rectifiers that are already attached to a heat sink and cooled by the forced air cooling the alternator was built with?

@lexicase8805 Жыл бұрын

I think this was my favourite of all your videos to date, and its super useful with the victron controller since they're multi voltage, theres no reason you couldnt set it to 12v and charge a dead car battery in an emergency, or run a 24 or 36v off grid setup too. I think this is now on my list of projects id like to do myself 😊

@johnrieger2461 6 ай бұрын

👍 Excellent project and nicely done ! Enjoyed watching 👍👍..

@jacobpoucher Жыл бұрын

Wow I've had this idea for years but you actually did it !

@vansgardens2304 Жыл бұрын

Great video! I’ve done similar building a welder, but I used the existing rectifier and used ring terminals to connect directly to the brush housing mounting screws (that have continuity with the brushes). I left the voltage regulator in place and just didn’t use it.

@SOLAR-cr5dp 11 ай бұрын

Great build David! The alternator truely puts out six phases, hence the need for two bridge rectifiers. The six stator windings consist of two sets of 3 wires, i.e. two individual STAR connections however, they are 180 degrees phase-shifted in order to provide you with a waveform (on the DC side of the dc-combined output) that has very little ripple.

@dwbogardus 6 ай бұрын

Yes, it would have been better to use the original 12 diodes that were pressed into their original heatsink. No need for the external diode bridges or heatsink. You can still get well over 100 volts DC, and the rated current of the alternator. I've done it before. The filter capacitor is a good idea, and needs to have a rated voltage well above the highest output voltage you ever expect from the alternator, like 200 VDC.

@dave56ize 5 ай бұрын

@@dwbogardus My thoughts exactly.

@altair7001 5 ай бұрын

The fact that the two windings are out of phase from each other is important to the best performance of the unit. Thanks @SOLAR-cr5dp for the info! Technically, would you agree to say that the two winding sets are at 60 degrees offset from each other, rather than 180 deg ? It would be interesting to see a similar project done with the original diodes! Edit: I see in another post below that the original diodes don't have a high enough voltage rating to be able to use them at 90 volts.

@hardhead7056 Ай бұрын

@@dwbogardus%100. Reminds me of one of those OVERLY complicated mousetraps..

@jamesbiggs9981 4 ай бұрын

This was a fantastic video. Great job. Your explanations were spot on. Very very informative. Thank you. I pulled the rectifier off and tested my voltage coming from mine and I had three wires pumping out 120v ac each. I just need to figure out how to marry it up to my breaker box and try and power my garage from that. You have given me hope that it is more than possible. Again thank you

@hanko456 Жыл бұрын

Hi Dave thanks for sharing your knowledge with us. I have a lot of fun. And great experience. You splanextion is very clear. Anybody understand very well

@AdamosDad Жыл бұрын

I have previously heard about getting high voltage from an automotive alternator, and wondered how it could be possible. But I found an article that explains this very clearly, and offers some guidance if you want to get maximum power. An alternator is designed so that the field (in the rotor) can be driven with 12 VDC from the battery, and produce at least 14 VDC on the stator (through diodes) to charge the battery at idle speed, which is generally about 600-900 RPM. The pulleys and belts usually provide up to 2x RPM boost, or 1200-1800 RPM at idle. However, at maximum engine speed (6000-9000 RPM), the alternator will spin at up to ten times faster than when idling, and the voltage on the stator (with 12V on the field) will then be as much as 10x higher, or as high as 140 VAC (three phase) and nearly 200 VDC through the diodes. A typical 50 amp alternator therefore could produce 200 x 50 = 10 kW or 15 HP, but mechanical limitations such as pulleys, belts, and bearings will in practice limit the power to 2 kW or so. The regulator serves to reduce the field voltage to about 1-2 VDC to produce the proper nominal 13.2 VDC charging voltage. The alternator typically has eight or more poles, so the output frequency may be nearly 1 kHz, and after full wave three phase rectification, will be smooth DC with less than 5% ripple. That DC voltage can be used to power tools with series wound (universal) motors, or most appliances such as modern TVs that use switching regulators. bbs.homeshopmachinist.net/forum/general/2006464-ot-getting-over-120-vac-from-car-alternator

@EmperorBun Жыл бұрын

This is awesome. Love the idea of de-limiting the alternator. I would also be very interested to see the fuel economy test-find the sweet spot and keep it running there. Another interesting idea might be to scavenge the waste heat from the engine to heat your hot water tank. Build your own combined-cycle heat and power setup!

@TheBeefSlayer 10 ай бұрын

I’m also a David and I live the idea of things you can do with alternator!!!! Got several projects in mind.

@joshuamheinrich4961 Жыл бұрын

Seeing A Man who knows what he needs put all of this together really Inspiring to me. If I can, I'd love to make one of these for myself.

@DavidPozEnergy Жыл бұрын

Go for it, it's fun. I have a part 2 video also: kzfaq.info/get/bejne/md9gp5ei1p7Rg2Q.html

@om617yota8 Жыл бұрын

Great build! Will definitely be doing something similar! Would definitely recommend moving all your electronics off the platform with the engine and alternator, before they get vibrated to death.

@artman001 Жыл бұрын

Dave, best diy project so far. You just proved several people wrong who said this wouldn’t work! Please do fuel consumption test at different RPM’s. I recommend rigid mounting the engine and use a ballasted mount, possibly a poured concrete base. Great job!

@DavidPozEnergy Жыл бұрын

Thanks. I wasn't setting out to prove anyone wrong, I just wanted to see if it would work. There are a couple 48V alternators on the market, but they cost more than my whole build.

@DavidPozEnergy Жыл бұрын

Interesting! Now you can share this video link with the Victron engineers and see what they say.

@D2O2 Жыл бұрын

@@artman001 They likely didn't understand what you were wanting to do exactly.

@lenbuckholtz2740 Жыл бұрын

cool that you had the two assistants.

@derekturner3272 5 ай бұрын

Adorable shop help crew.

@OriginalBtwiceborn Жыл бұрын

One improvement I would consider is separating as many components as possible from the engine vibration. Great build

@jamesgrossmann866 Жыл бұрын

As an electrical engineer, I'm really trying to figure out why you removed the original rectifier diode system from the alternator. I don't see how that modification did anything but complicate your design. the original diodes were cooled by the alternator and were designed for the high voltages involved. I also think a small, simple circuit could also be built to replace the regulator and regulate the alternator output. If it were designed correctly, you could be much more in control of the output voltage instead of just hoping it will work with your charge controller.

@TroyWarr1980 Жыл бұрын

@None of your Business I assume you're trolling, but there's no meaningful difference in charging off-grid batteries with a generator vs. powering a home with a generator. In fact, the former is more efficient because you're storing extra energy you don't immediately need. This is just a back-up solution for times when solar isn't enough

@researcher4good 9 ай бұрын

Totally agree. Remove regulator. Connect field wire to ungrounded side of brushes. Done. After seeing how easy that is, I'm going to use newer 200a alternators with the regulator removed instead of early 80s ford 100a designs with external regulators. I was wondering what the diode voltage rating was.

@dandeson9723 9 ай бұрын

You learn from your mistakes, also the capacitor wires could be bigger or it should have been placed between the output and controller to minimize resistance, the wires carry alot of current between every cycle.

@manuelsilva8640 9 ай бұрын

The car alternator bridge rectifier diodes reverse breakdown voltage will be from 60 to 100V. For the intended > 80V the diodes replacement was the right call.

@teslamac5348 9 ай бұрын

Quick search finds the similar alternator diodes SG-C17xxZ27 are zener making part of the regulator and back biased clamping to 30v max. Swapping to a bridge was the right way to go.

@miker2753 10 ай бұрын

this presentation was very informative and helpful. Have a project I've been putzing with and this knowledge and incite should be very useful. Thank you for being thorough with your explanation on everything.😁

@stewarttate 8 ай бұрын

Nice work Dave.

@tomhardin8393 Жыл бұрын

Congratulations David. It works! It got my attention but in a different way. Some day I want to try this by powering it with wind. I had thought I would have to put 4 alternators in series (good luck with that 😮) but you showed a single alternator can put out enough voltage to work in a 48 volt system. I’m excited!

@off6848 10 ай бұрын

It takes about 5BHP for a wind turbine to make 40ish amps on an alternator in builds I've seen. You'd need quite a large and powerful wind turbine to spin 4 alternators.

@ThinkFab Жыл бұрын

David, my dude, mad props for going after this build and actually documenting it to the extent you have. I recently replaced my alternator due to the voltage regulator going bad but saved the old alternator for a project like this. Time to take your skills and knowledge and make a thing out of it. Thank you!

@DavidPozEnergy Жыл бұрын

Your welcome. Your situation is perfect! I would have used an old alternator if I had one lying around.

@drewstudlino5885 Жыл бұрын

Good stuff man! watched all ! great video 👍

@drunkjonboy Жыл бұрын

This video has been in my save to watch later for 2 weeks now. I’m glad I watched it. This is awesome. I want to see this set up with a hho generator

@drunkjonboy Жыл бұрын

Hho or wood gas.

@deuspax Жыл бұрын

This DIY is great!!! you managed to pull from 6.6hp engine a 3kW from a handmade contraption when maxed, which is awesome. PLEASE do the efficiency test, it is quite interesting to find where is the lowest point for

@TheRainHarvester Жыл бұрын

3kW = 2100 HP. So 33% efficient?

@thehairs2018 Жыл бұрын

Mount the engine solid to the board and use vibration control under the base. Maybe to another board with rubber feet. This would also help with belt tension. You could also use a turnbuckle for better control of the tension. Love the idea, and glad I found your channel to subscribe.

@ArmandPedroza 4 ай бұрын

I have watched this video 6 times already. Great video, very detailed.

@thinkingoutloud6741 5 ай бұрын

Great video. Thank you. Lots to learn here, and room for additional ideas. I think knowing the actual horsepower output of the engine would be interesting, rather than accepting the rated output.

@mr.goldenrod291 Жыл бұрын

Well done! “It all worked.” I’ve been experimenting with solar systems, batteries, generators, inverters for 15 years and I often state the same phrase (followed by “didn’t start a fire or get electrocuted”.) The frustrating part of this type of experimentation is it shouldn’t be so difficult. There’s too much info that is kept from the masses.

@pauledwardb82000 Жыл бұрын

Alternator brackets should be mounted to the engine not the platform since the engine is on isolators. The motor mounts are fighting the belt tension causing the osilation in current configuration. Think of how an Alternator is hard mounted to the engine in a car but the whole assembly is on rubber mounts.

@DavidPozEnergy Жыл бұрын

Thank you, that's a great idea. I can make a sub-platform to hold both. I was scratching my head on it. "Why is it still walking around...".

@GalloPazzesco 3 ай бұрын

Wow, outstanding. I've watched this three times and have literally taken notes, drawn diagrams, paused along the way ... best class on this type of build for my Lister Peter diesel build I could have hoped for. Been a long time fan of yours David. If I had your hair I could have been President. Subscribed, bell rung, commented, upvoted, liked, shared ... may the algorithm gods smile favorably upon your channel friend.

@DavidPozEnergy 3 ай бұрын

Thank you very much. I made improvements in Part 2 and 3 of this project. If you build something with your diesel engine, please send me a link. I'd love to check it out.

@tangoreal9098 10 ай бұрын

Outstanding! I believe thanks to you I have found a solution for my sailboat.

@ronniepirtlejr2606 Жыл бұрын

To have less vibrations, you could build a solid metal frame & add rubber bushings ( motor mounts) . Maybe add a spring pulley tensioner? And of course, if you wanted the ultimate smoothness, you would have to replace the Predator with a Honda engine. But that last part is a considerable amount of cost!

@shanesdiy Жыл бұрын

Very cool project! Good job. My only advice is change that main breaker. That 125A breaker is not rated for DC applications, only AC. It will not be able to efficiently suppress the arc in a high amp dc load if you were to overload it. Breakers rated for both DC and AC will have AC and DC symbols on the breaker. On that breaker you can see it only shows "400~ 50Hz" which is AC only.

@iamhe999 10 ай бұрын

Very Cool David.. It is an experiment that paid off, now for version two.. and three.. and four..

@DavidPozEnergy 10 ай бұрын

Part 2 and 3 are live if you want to check them out.

@alext8828 7 ай бұрын

I liked the 2 thou interference fit with the adapter you made.

@ckiottest5281 Жыл бұрын

Great test! You should run a fuel economy test on this. I've been looking to do something similar.

@Crash5291 Жыл бұрын

Interesting indeed! I would thing that the mounts you added would work better if the Engine and alt were on the same mounting surface, it would also make adjusting the belt simpler and eliminate the flex between the motor and alt. Depending on the Alt brand some come with a dyno sheet showing the output vs shaft rpm could be handy in setting up the belt drive ratio. Cheers