love your vids brother! on the insulation though for the benefit of others intending to replicate same way,... the shiny side utilises radiant reflectics. Radiant barriers and reflective insulation systems work by reducing radiant heat gain. To be effective, the reflective surface must face an air space in order to be able to reflect any radiant heat. Having it face the metal (glue) without an air gap inbetween, turn them ineffective and (without the glue) just extension of the van panel and a heat conductor.
@hennnnerz10 ай бұрын
So likewise on the inside it wouldn't work unless there was an air gap? Before adding the ply, or carpet for example?
@marekondrus557910 ай бұрын
@@hennnnerz that's correct
@maradall3 жыл бұрын
As a fellow Aussie, I'm really happy to have an Aussie perspective on van insulation! Very well explained too, just the right amount of detail. Looking forward to watching the rest of this build!
@SALTYVANVENTURES3 жыл бұрын
Glad it was helpful!
@theswanniesdownunder24173 жыл бұрын
Me too
@zephrid2 жыл бұрын
Hey sorry, I appreciate the sharing of info but I'm going to suggest that this isn't really the best solution. Foil backed insulation is designed to work with an air gap either side, preferably of 40mm. Sticking this directly against your metal panels just adds to the conduction. Without the reflectivity doing anything you are left with EPS, which is not the best thermal insulator (XPS would be better, for example). On your ceiling, you could use an air gap of around 10mm above and 5mm below the foilboard in order to get some benefit from the silver layers. I wouldn't normally say anything but I think labelling this the 'best insulation' is misleading. All the best anyway.
@kangacrew5402 жыл бұрын
Yr right. No need to glue too. Foil board is so light taping with insulating tape on the sides does the trick for ceiling and use spacers on walls. He did a good job though. Like the deadening on the walls.
@AZRockRunner2 жыл бұрын
Hah, I almost write a comment for the same thing. That foil won't reflect any heat, mate (Heat Transfer ME401). If it is flipped 180 degree, it can be a moisture barrier and reflect the heat back in the winter.
@tommyk39782 жыл бұрын
Where did you get that information?
@mtwata6 ай бұрын
@@tommyk3978 That's how they are designed to work
@jordanhanson3162 ай бұрын
Same opinion, I wonder if adding the poly first then the board would be better as it’s lower density and won’t absorb the heat as much.
@starccs3 жыл бұрын
I decided to sub to your channel after seeing you literally cut 120 wires and soldered them together. What an effort!
@SALTYVANVENTURES3 жыл бұрын
Haha dedication right. I thick each look actually had 68 wires each so that works out to be 272 solders! But who’s counting haha
@roadrunner50843 жыл бұрын
Finally!!! My fellow Aussies that know how to insulate the Australian way lol ✌🏼 You guys got an new Van congratulations 🎊 forward to watching all the videos 🤙🏼🇦🇺
@SALTYVANVENTURES3 жыл бұрын
Good to hear this video is reaching the designated audience. Welcome aboard mate!
@davidlock2647Ай бұрын
Love your work, although wiring loom through metal rather than over metal is problematic in years to come. Keep Up the good work.
@youtubkeeper3 жыл бұрын
Solid advice mate! The polyester doesn't hold moisture is another important point, whereas other types need an air-gap to ensure air flows around it and removes moisture. Not really possible in a van build a lot of the time.
@SALTYVANVENTURES3 жыл бұрын
Exactly!
@pricewiseinsulation5 ай бұрын
Great video! Thanks for tagging our insulation product in your description. We love seeing Bradford Polymax Insulation being put to good use!
@SALTYVANVENTURES5 ай бұрын
Love the product! Perfect for van builds
@mikefranks4528 Жыл бұрын
For my Ford transit, I am NOT going to reroute the Ford wiring loom leading to the back. it’s really not needed. Ford did that so that you can have access in the event you need to maintain that system. So I’m just going to create a race track for it at the top corner on the driver side to accommodate that loom in the event that I need to get to it.
@moniqueg76253 жыл бұрын
I love how you think about the smallest details, wish you could build my van....best of luck!!
@Nickolas383 жыл бұрын
Good job! I watch the channel while in Siberia. You have nice weather to travel all year round
@SALTYVANVENTURES3 жыл бұрын
Thank you!
@charlietipene78183 жыл бұрын
bro you are the man,I like all your ideas
@SALTYVANVENTURES3 жыл бұрын
Thank, appreciate it!
@genoromblon71373 жыл бұрын
This is very informative. I wish O can build my own van conversion in the near future.
@SALTYVANVENTURES3 жыл бұрын
Thanks you. You can build your own! i've seen people with zero building skills build their own van!
@R32WA2 жыл бұрын
Awesome video, great to see stuff in Aus, keen to build mine. Good luck
@SALTYVANVENTURES2 жыл бұрын
Good luck!
@Molly.and.squeak3 жыл бұрын
Holy crappers! That wiring would have done my head in!! Bloody ford!
@SALTYVANVENTURES3 жыл бұрын
Right! I don't know what they would have done that, and they did add any joiners either. Very frustrating but I'm glad its done and that everything still worked too! bonus haha!
@Molly.and.squeak3 жыл бұрын
@@SALTYVANVENTURES You definitely have more patience than me!!!
@KatrinaQuisilVlogs3 жыл бұрын
Awesome! Looks like a lot of job on the wirings, but I'm pretty sure you can do that.
@SALTYVANVENTURES3 жыл бұрын
Yes it was a nightmare of a job! I'm glad it is all over and that everything still ended up working in the end
@Deane142 жыл бұрын
Hey mate, I'm about to start my first Van build in a couple weeks and before I purchase some of the same materials I was was hoping for an update on things u really like/regret/would do differently. Can be with Insulation, Materials or just layout. Appreciate any and all info no matter how much, the more the better! Cheers,
@milospesic24543 жыл бұрын
You cant installe it "backwards" but it doesn't matter. Both sides are reflective foil. Green is antiglare for jobsite safety
@SALTYVANVENTURES3 жыл бұрын
yeh that makes sense! Cheers
@chrismorgan90833 жыл бұрын
mate, those bloody wires!! i haven't seen anyone mention them before. Iv just started my conversion and have been trying to think of a way to move them. FFS. Might just take it to a pro., or find some way of hiding them. Thanks for mentioning though, they are guna be huge headache. Good work Ill defo have my insulation the other way though mate, we in UK, are on the other side of the weather spectrum
@SALTYVANVENTURES3 жыл бұрын
Yeh I couldn't find any information anywhere about what anyone else had done so I thought people would get some use out of it. If you are going to use quite thick wall insulation, you may be able to get away with not having to hide the cables though and just leave them on the outside. I didn't have that option with the insulation I wanted to use.
@Happyexplorers_au3 жыл бұрын
Great video mate! 👌🏼
@SALTYVANVENTURES3 жыл бұрын
Thanks!
@CraftedbyMonnowLane2 жыл бұрын
Awesome video. Thanks so much
@SALTYVANVENTURES2 жыл бұрын
Glad you liked it!
@lukemckee97723 жыл бұрын
Hey man just bought a 2016 transit similar to yours, building it out in Adelaide, great video so far, I'll watch more for great ideas I've slept in it bare a few times the cargo area stays quiet cool so I'm thinking thinner insulation, with a little heater and a refrigerated aircon
@SALTYVANVENTURES3 жыл бұрын
That's awesome. From what I have seen so far they are great vans. I agree I think in Australia the 1/2 a foot thick insulation is a massive overkill. I have also installed a diesel heater (video to come) which is plumber into the diesel tank and it is great! pumps out some serious heat.
@lukemckee97723 жыл бұрын
@@SALTYVANVENTURES what about cooling? Are you going to install a little 1.4kw aircon? Nice im excited to see more, we just installed the sound deadening hopefully we will post a timlapse
@SALTYVANVENTURES3 жыл бұрын
@@lukemckee9772 I'm not going to add any refrigerated cooling. With the exhausted fan on and the window near the bed, it draws a lot of air and will cool the van. I'm ok sleeping in pretty hot places as I've lived in the tropics with no AC. Ill add a 12v dc fan too to the mix.
@NoName-ds5uq2 жыл бұрын
Firstly, I’m a little concerned you chose a Transit. Their engines aren’t the most reliable out there. Make sure you maintain it fastidiously! I have many years in the transport industry and they don’t have a great reputation here. More recently I was told by a Land Rover mechanic that the Transit engine went into the Land Rover Defender as well and doesn’t have a great record. This was as I was picking up an old engine and dropping off a new one… Secondly, what kind of temperatures are you talking about here? Snowy Mountains, Tasmanian Central Plateau or more coastal locations? I’m interested in doing everything in this beautiful big country. I’m only separated by a small moat from Victoria.
@tommcallister1879 ай бұрын
According to the company it does not make any difference if the silver side of the foil board is facing in or out.
@dragomir81922 жыл бұрын
It's great to see you taking care in all aspects, rolling over all your stuck on insulation, ensuring air gaps etc but PLEASE for the love of God, just buy a few cable connector strips instead of soldering over a 100 wires 😭
@SALTYVANVENTURES2 жыл бұрын
Haha the only way i would be satisfied that the connection was going to last was to solder it myself.
@MimiBondi3 жыл бұрын
Hey, so happy to see the exact van we are going for getting built 😊 Thanks for all your videos and tips, they are awesome and very appreciated! I noticed you changed the bench seat to a single seat which is what we also want to do but concerned about the side airbags. Could you explain how you did this?
@tatianahernandez17373 жыл бұрын
Hey Mimi, Did you find the solution to change to a single seat? I'm looking to do the same in my ford transit. Thanks!
@MimiBondi3 жыл бұрын
@@tatianahernandez1737 still have no idea 😂
@kipkip76883 жыл бұрын
Great video mate, thanks for all the content. We just got a transit and are trying to wrap our heads around the insulation (and the 27,000 other things that we need to consider). We're building it in France, to live in throughout Europe; you think your system would be equally as good here? Don't suppose you have advice on vapour barriers? Cheers.
@SALTYVANVENTURES3 жыл бұрын
Sounds great! I'd say the insulation would be sufficient but there is not reason you cant add a little extra if you like. I probably would instal a vapour barrier if i were to build a van in Europe. The wetter and cooler climate would make a lot more moisture than here in Australia. In New Zealand we use 2mm flooring underlay as a vapour barrier which also doubled as a bit of extra insulation as it is 2mm of foam with a foil backing and is water tight. Good luck on the build!
@lilyhenry863 жыл бұрын
Hi😊😊.. love ur work👍👍...where dd u buy your rear slide windows plez??😁
@SALTYVANVENTURES3 жыл бұрын
Hi, check out the video here where I installed them. The link to the windows is in the description of that video kzfaq.info/get/bejne/kKqRmrRl3M7Vg2Q.html
@nunziobianco54162 жыл бұрын
Hi I’m in the should or should I not do it my self phase .what did u use to cut the foil board ? Thank u
@SALTYVANVENTURES2 жыл бұрын
Just a nice sharp razor blade. Get the long retraceable ones, not the shorter stanley version so to make sure the blade is longer that the board it thick
@MrRyanpdx322 жыл бұрын
I only watch because your so amazingly oh my gosh so gorgeous! Your like 3 triple rainbows. Your so cute. Oh and I need a roof rack for my car. Your still cute
@tyw14443 жыл бұрын
going to follow this exactly for my insulation! how many foil board sheets did you need?
@SALTYVANVENTURES3 жыл бұрын
I think it was 2 in the floor, 1 for the walls then another 2 or 3 for the roof so a total of 6 i think
@aleeshapea75373 жыл бұрын
Where did you purchase the deadener? Did you end up using all of it? Thanks!
@SALTYVANVENTURES3 жыл бұрын
I purchased it on eBay. Yes is still have about half a roll left!
@sallybt43 жыл бұрын
Thanks for all your great videos, Vendu and Marci. My partner and I are building our own van and find them so helpful! This week we have carefully installed two layers of foilboard like in your video. However, when we go for a drive it creaks and squeeks. We've made sure it's not rubbing on the horizontal roof supports. Have you had this problem? We think we'll have to pull it all down and try and different glue, or a layer of something spongy. Any recommendations or tips to avoid squeaking next time around? Thanks in advance!
@SALTYVANVENTURES3 жыл бұрын
Hi James thank you we really appreciate the feedback. Sorry to hear about your insulation debacle. I didn’t experience any major squeaking I can recall, and if I did it has defiantly settled and disappeared now. What contact adhesive were you using? And did you apply it liberally? I have used some pretty ordinary contact adhesives in the past. Some are only made for paper and cardboard for things like clip boarding. The kwikgrips one I used I have found to be really good. If you cover the whole sheet on both sides it should be like one sheet with no movements or room to squeak. The other thing I might suggest is to fill around the gaps with some filler foam to stop any movement. Let me know how you go!
@sallybt43 жыл бұрын
@@SALTYVANVENTURES Thanks for the quick reply! We used Sika brand spray adhesive on some panels and Sika Contact Fix on others. We thought we were using a lot but if I could go back I'd use even more. We've managed to reduce the squeaking alot by carefully pulling down a few sheets and reinstalling them, trimming and masking edges that rubbed when the car moved and applying Sikaflex Pro to some of the joints. We're yet to use spray foam but might give that a go too. Fingers crossed the last few squeaks disappear with time! Thanks again for your videos and suggestions.
@jamesdettmann17552 жыл бұрын
Hey mate how did you go with the squeeking? Also do you just hold the foilboard to the roof for a few mins while the spray adhesive dries and thats enough? I have put sound deadener on the roof but not the foilboard yet. I also had squeeking when i drove my van but only really have the flooring down, im hoping it was just some of the loose timber i had in the back making the noise
@sallybt42 жыл бұрын
@@jamesdettmann1755 The squeaking eventually stopped. We drove around in the back listening to find the worse spots and replaced them. The squeaking seemed to occur where the corners of the foilboard rubbed against the van and where poor adhesion allowed the pieces of foilboard to move. I recommend propping a sheet of ply or similar up to hold the foilboard in place while the glue sets - we used tent poles. Use the best spray adhesive you can find. If we did it again though, we'd look into alternatives that don't squeak. Good luck!
@jamesdettmann17552 жыл бұрын
@@sallybt4 great thanks. I think im going to use stick pins as well as spray adhesive to hold it on too. Cheers.
@maarinash7 ай бұрын
Hi! What's that spray you use to stick the insulation in the walls? :)
@SALTYVANVENTURES7 ай бұрын
It’s called spray on contact adhesive
@gregkelly22333 жыл бұрын
Hey mate with the poly stuff where you at all concerned about it getting damp? I know you said it wont rot but would mould be an issue with condensation? Or am i thinking too far into it lol
@SALTYVANVENTURES3 жыл бұрын
Im personally not really concerned. The age old debate if insulation requires a vapour barrier or not, In my opinion from what i've noticed is that in the climate we live in it's not necessary. Wood also breaths so the moisture, if any, doesn't get trapped behind the walls like you might think. If you maintain good ventilation when sleeping and cooking you will minimise the moisture in the van.
@jasongarcia75443 жыл бұрын
just buy a Deutsch 60 pin plug?
@SALTYVANVENTURES3 жыл бұрын
would have need at least 2 of those per join
@flyingdutch98183 жыл бұрын
Re noise ,everyone forgets the most noisy part of a van when driving; the footwell next to your seat. Silver facing out on the foilboard will do sweetfa if up against the shell of the van. 15mm of foilboard in Oz??? Seriously? 1.5R insulation when 6.0R costs only a few bucks more; the reason you were toasty in the front of the van whilst condensation was on the from windscreen was because of.... you! The average person expels over a litre of water whilst sleeping. That rear wiring being on the outside is a shit;; Mk7 transits and prior it’s in the recess. Feel your pain cutting and reconnecting those 60+ wires.
@SALTYVANVENTURES3 жыл бұрын
I was actually planning on using the remaining sound deadener I have in the cab, in the doors and under the seats when i get around to it. I've only used 15mm foil board around the East West bed configuration to get the maximum width. Then glued 5mm ply over the boards. Sacrifices need to be made to get my long legs in the bed! The rest of the van will have 30mm and polyester insulation. More than enough I've found in the past. With the low R rating of the polyester, it really is enough from what I've found plus I preferer it much better than a lot of other products with higher ratings as it doesn't absorb moister, doesn't rot and isn't irritant. Yes in NZ the windows in the back were not frozen because of our condensation but the proof is that we were not freezing cold like out buddies next to us in the same van with zero insulation. And where this van will go in Australia wont be as cold as the NZ winter.
@shelleyneilon85502 жыл бұрын
Great video thanks 😊 I am also using foilboard and I have a question - how do you cut it to minimise the mess (looks like a bean bag explosion 💥) Shelley (also an Aussie)
@SALTYVANVENTURES2 жыл бұрын
Get the long snappable razor blades. Makes sure you use a brand new one and it will cut like butter. Use a straight edge to get nice clean cuts with no mess.
@shelleyneilon85502 жыл бұрын
@@SALTYVANVENTURES thanks will give it a go
@makeoverseas13693 жыл бұрын
How did you find the sound deadener quality? I missed out on the mk8 transit so I'm sticking with my mk7 now and watching this is giving me a kick in the arse! I was looking at the sound deadening and closed cell foam from a company in Victoria (i won't mention their name) and the price is way out of my price range. So I'm very interested in what you used. Have you ever used the closed cell foam? I was going to go that way and use the polyester as you have. At least I don't have the problem with that wiring loom running all the way outside the wall like a mk8, what a nightmare! :)
@SALTYVANVENTURES3 жыл бұрын
The sound deadener has been amazing so far. Honestly i don't think you would notice the slightest difference between the cheap and expensive stuff. The stuff i bought was cheap off ebay and it super quite while driving. And I only covered about 40% of the panels with a heap left over. I haven't used the closed cell foam myself as a sound deadener so i cant comment on that front. I did use it however as insulation on a window in our hiace van that worked well. Worked well to black out the window. I would advise not to spend too much time and money on the sound deadener as in my opinion i don't think it really makes a hug difference anyway once all the walls are up.
@makeoverseas13693 жыл бұрын
@@SALTYVANVENTURES Thanks mate, that's what I was hoping to hear, it all the sound deadener looks so similar, but you can pay 2/3 times as much as the ebay stuff for a brand name product! I'll order some and I'll get a roll of the 10mm closed cell foam and see what the quality is, I want to use that for thermal insulation. Keep it coming!!
@markhiggins30542 жыл бұрын
Your vids are so great thank you - does the foil board flex a bit to allow for the radius of the roof? Thank you
@SALTYVANVENTURES2 жыл бұрын
Yes, absolutely, its flexes well to conform the the roof shape
@xenosonic3 жыл бұрын
Vapor barrier?
@SALTYVANVENTURES3 жыл бұрын
I didn't install the highly controversial vapour barrier no. I don't really think it's necessary as long as the insulation you use does not absorb moisture it wont get trapped behind the walls. Wood breaths unlike some other materials so i'm not worried about any issues.
@theswanniesdownunder24173 жыл бұрын
Did you use Vapour barrier on this build?
@SALTYVANVENTURES3 жыл бұрын
No not on this van. I did on my New Zealand van where it is a much wetter climate compared to Australia.
@dmartil733 жыл бұрын
Where did you get your sound deadener from?
@SALTYVANVENTURES3 жыл бұрын
I bought it on Ebay. This is the one I purchased www.ebay.com.au/itm/162797922478
@dmartil733 жыл бұрын
@@SALTYVANVENTURES Thanks mate.
@shanemckean33812 жыл бұрын
Hi Can you please tell me the quality of ply? can I use a standard CD grade or do I need to use a Structural CD grade? Thanks for the awesome information in all your vids
@SALTYVANVENTURES2 жыл бұрын
I used CD non structural ply. Its not the bets quality but far cheaper than other grades of ply and the price adds up quick. Structural ply is required for buildings where specific certifications are required as they are quality controlled and strength tested. Not required ever in a van.
@acwbagnall3 жыл бұрын
Hey mate, what size of wires did you get to lengthen the loom? I'm about to embark on this nightmare
@SALTYVANVENTURES3 жыл бұрын
I got a loom from a wrecker so all the wires were already the same size and the same colors. I'd recommend it if attempting to do this.
@MrFredyful3 жыл бұрын
Have you had any problems with condensation behind your foil board?
@SALTYVANVENTURES3 жыл бұрын
Not that I’m aware of no
@0NetherCraft0 Жыл бұрын
Did you have any squeaking problems with the foilboard?
@SALTYVANVENTURES Жыл бұрын
none
@rebeccamchardy43673 жыл бұрын
Did you have to get the polyester insulation as a special order from Bunnings? Can't seem to find it in stock anywhere in Sydney
@SALTYVANVENTURES3 жыл бұрын
Hi, I didn't buy it from Bunnings as they don't stock it. I purchased it from a insulation warehouse in Brookvale. Can't remember the name of it but any good gyprock or insulation shop should sell it.
@rebeccamchardy43673 жыл бұрын
@@SALTYVANVENTURES Thanks there is a Gyprock Trade Centre place in Penrith & looks like they have it
@scrummybunsmckenzie51722 жыл бұрын
Hi salty I M use wanted to know if your Ford transit was LWB or MWB .I am about to purchase one .I have saved all your videos and subscribed .so I can keep up to date thanks shane
@SALTYVANVENTURES2 жыл бұрын
Hi, It is a long wheel base high roof 350L (not the extended version)
@scrummybunsmckenzie51722 жыл бұрын
@@SALTYVANVENTURES thank you so much for the quick reply
@SAVANNAH747 Жыл бұрын
What is the name of the spray glue you used & also where can I get the polyester
@SALTYVANVENTURES Жыл бұрын
I believe it’s was kwik spray adhesive. You can get the foil board from Bunnings
@pricewiseinsulation5 ай бұрын
Hi @savannah747, we supply the Bradford Polymax Insulation that was used for this project.
@StrayanRider Жыл бұрын
I'm dreading going to have to be doing the same cut and shove of that loom. What a disaster by ford.
@SALTYVANVENTURES Жыл бұрын
total pain in the ass. You can also hide it behind the overhead cabinets too
@StrayanRider Жыл бұрын
@@SALTYVANVENTURES I've got a bedlift going right to the roof on actuators, so I defo need to do the cut and shove you did. Sigh.
@joewilson66473 жыл бұрын
Hi there, doing a 2007 transit in NZ, saw that you have done a previous build in NZ. Was wondering what insulation you used in NZ for the walls and roof? Keep up the videos! And cant wait to see what you did with your ladder!!!
@SALTYVANVENTURES3 жыл бұрын
Have a look at these 2 posts we did on the insulation when we were building our NZ van. This should answer all your questions. instagram.com/p/BtnRWpNnawk/? instagram.com/p/Bt3-9OQgvqF/?
@dorknuckle2 жыл бұрын
As a pure spectator at this point is there any value in using the cubby holes along the roof edge or is it just too hard to incorporate it into the build.
@SALTYVANVENTURES2 жыл бұрын
I would say no. not enough bang for your buck id say
@allegrosotto21263 жыл бұрын
Have you checked the toxins in the glues and insulation? Interior air quality in cans is so important.
@FatemaHira-oq1dw3 жыл бұрын
Will this insulation be warm enough during winter in snowy mountain??
@SALTYVANVENTURES3 жыл бұрын
Yes i believe so....well it depends on what snowy mountains you are talking about. Australian snowy mountains yes. We used the same insulation in our NZ van and that was cold and icy and we were happy with the insulation we used. Canadian snowy mountains, probably now. I've also installed a diesel heater that works amazingly in the cold!
@FatemaHira-oq1dw3 жыл бұрын
Thanks.
@terrywalsh67212 жыл бұрын
Hi, how is your roof vent going , as we were looking at the maxxfan but this is a lot cheaper, and wanted your opinion, thanks
@SALTYVANVENTURES2 жыл бұрын
It’s going well. The only downside to this fan is not being able to run it fully when it’s raining. Light rain it can handle as you can crack it open enough not to let water in but still enough to exhaust but heavy rain you need to close it. Can be a bit annoying sometimes a other than that it’s been great and worth the savings
@shanemckean33812 жыл бұрын
Hi Where do I purchase the roll of sound deadener?
@SALTYVANVENTURES2 жыл бұрын
The link is in the description!
@samsmith45972 жыл бұрын
Would that insulation be sufficient enough for nz?
@SALTYVANVENTURES2 жыл бұрын
Yes, its the same as what we used for our NZ van
@roddas262 жыл бұрын
Have you ever used wool for insulation?
@SALTYVANVENTURES2 жыл бұрын
No, And I personally wouldn't want to either.
@roddas262 жыл бұрын
@@SALTYVANVENTURES interesting. Seems like a sensible option?
@vickimathews19702 жыл бұрын
Just saw your video, Max did his van build last year, not sure if you saw this kzfaq.info/get/bejne/rb93mrSknc3WhYU.html he explains PIR board vs Foil board, any thoughts?
@SALTYVANVENTURES2 жыл бұрын
I mean its personal preference. I don't necessarily agree with his statement around foil board. If it's glued in, no mater how much the van vibrates its not coming out and it doesn't crumble like that. It's easy to cut with a sharp knife. It may be slightly more permeable to water but that if pretty negligible unless your soaking your walls and roof with water. I'm a believer that you need your walls to breath and that a vapour barrier if not done so carefully and correct could actually do the opposite and trap moisture in. But thats my opinion and many will have different ones too.
@fbwqmyxd6j3 жыл бұрын
Good job,but it will probably be a waste of time ,seeing as you bought a transit.Those things have a great body,but the running gear is absolute CRAP!Gear boxes failing at 300k or less,replacement parts are a f-cking rip off(2500 to replace an injector pump)and about 7000 grand for a reco motor...i,ll put up with no room,and buy a toyota!
@aminadesnomades66363 жыл бұрын
Hey guys, just wondering, do you have any feedback on the Voltax battery? Seems too cheap for a Lithium battery. Good content, loved the gas box video, we installed the same but we struggled a bit to get it done (Newbs :) )
@SALTYVANVENTURES3 жыл бұрын
No issues so far! We haven’t been running it full time as we have only now just finished the van but it’s got grunt to power our 2000w inverter no problems. Haven’t seen a decrease in performance since I bought it last August. Also chargers super quick, well compared to lead acid batteries