What’s up man, I followed your advice & got with Jimmy picking up my unit this month. Always appreciate the honesty of your videos. Not too sure if you still see the comments of old videos, but preciate all that you do my dude. When I link up with J Hall I will get him to give you a ring.

Great video! Thanks for explaining sizes needed, kind, best, and what works! LEADERSHIP! BIG RAY👊

Yo Ray! Built both my setups after this video! Haven’t seen anything from you lately, hope all is well man! Thanks again for all the awesome info

You and Freddie pressure washer are my 2 favorite so far you guys give so much great infos that are free

Thanks for the great video. I’ve been looking to replace my current Softwash gun and I’m going to try this one out. Also, I use tape and true blue on all my fittings as well and never have a problem.

Great video bro! Great content! Using your gun setups and lovin it !

thanks for this great vid Ray ive been waiting on this jewel info. Thanks for looking out for us

thanks for the solid advice!

Great video, exactly what I was looking for.

You put out the best videos period!

Thank you Ray great video!

Yes sir that high pressure ball valve set up is great!! that is the same way I run mine and ever since I have gone to that I haven’t gone back to a gun!!

Thank You For This One Ray 🔥💎

Great video Ray. Thanks for the information!

That was some great info Ray. I do like your high pressure gun set up. Thanks for sharing.

What's up Ray! Awesome video of the breakdown of all the fittings and gun!

This I'd the exact video I needed. Just about to start my pressure/softwash business and I bought one those Northern Tool softwash system but I hate the hose that it comes with also the gun doesn't swivel so I have to fight it every little move I make. Thank you.

Thanks for the video I use a 1/2 banjo poly male camlock in my gun for my gas roof pump and 12v and I have a female banjo camlock with 1/2 cut off valve to 1/2 barb! This allows me to change out guns and to cut flow on off and so I can crank up my gas roof pump without pulling the trigger on the gun just leave valve open on the end of my hose! I can reel hose up without leaving gun on the end because I can easily disconnect!

great content, thanks for the tips Ray appreciate your work

This was really simple to follow. I thank you. My guns are coming up for replacement and I am going to build these for when they crap out.

A lot of good info. Thanks for sharing.

I love the video. You are the man. I use blue tape on all my fittings. No need for anything after that.

“The forbidden red tip” 🤣

Man I had completely forgotten about goat wrenches. I paused this video and ordered one!

New to the channel and new to pressure washing. trying to get in the game and this hose setup is great. carpal tunnel is no joke. ill be leaning on you for for info. thanks.

I just ask you about this topic. Thanks again for sharing

I’ve been eying your ball valve gun since I saw you using it. I’ve had a carpal tunnel release on my right hand, and I’m now due for the left hand. I really think this will help out with pain/fatigue. Thanks for showing the build!

Thanks for making this content, my hand has been sore from the gun.

Great video ray ray

Thanks Ray!

Great vid

Nice vid Ray 👏

Hey Ray! I have somehow missed your channel and discovered it last week. You have some of the best content out there for pressure washing peeps! Really great stuff, keep it up and keep inspiring us newbies! One video I would love to see you do would be a typical onsite quote process or an upsell process. There is no real content on selling or upselling pressure washing services and it would be a great help. Anyhow, keep grinding Brother!

Good stuff!

Whole video is great but that smooth jazz at 9:04 hits different

Brother great content. I just posted my ball valve set up on wash life everybody slammed it bc I had the same adapter set up on the end for 1/4” everyone in there said man that too much steel lol thanks for the back up! Bet you won’t hear nothing

I’ve added a ball valve on my softwash which help when dragging hoses and rolling up, I disconnect the gun and helps when I’m off trigger and the gun leaks.

I really like the pressure washer gun idea I would use it if not for employees bc of the auto shutoff like you siad. Looking forward to the new chem video!

Hey Ray! Thanks for video! Question so if got male plug going out, when you use surface cleaner you have female QC coming off of it?

Thanks

Question about that black handle ball valve. I just bought one and when my machine gets pressure that handle is damn near locked and i cant get much leverage with it. Do you use wd40 or pbblaster to help ease that valve?

Can you use these gun setups on a regular 4gpm 4200psi setup? You carry such knowledge and am super grateful for. These videos. About to start out in south Florida

Awesome setup, where did you get those stainless quick connects and adaptors?

Thanks Ray. Will you go over the dirt killer mix ratios for the mango grotto, maximus foam, kracken wash?

I have questions about Sherrill William paint organic pigment.what u gonna do if that house used that paint? Thank you sir

Thoughts on how to supply 12 gpm from 275 gallon ibc tote? Maybe run two hoses from ibc to one hose to increase water flow

Question. Can you use that pressure washer hose setup to rinse your chemical off a house with oxidation? Would that be too much pressure or can the tip adjust to a point where you can safely rinse without running the risk of removing some of the oxidation? I'm just curious because I use the 12 volt to apply chem and would like to use my pressure washer to rinse. Thanks!

Do you have a link for the viton rings? What's the best gun recommend for a 3800 PSI 3.5 GPM pressure washer?

I like it.

Greetings from malaysia. Need ur advice on whats the best solution to remove bat guano from a painted wall. Thakns in advance. Super good job uv done ray boy.

Great video and great content. Thanks for sharing. I love your shirts! May I ask where you got them? Thank you.

Hey ray you’re my go to channel for good PW info.. just wondering, what would you use the pressure washing gun for vs the soft wash side? They look to have roughly the same flow and pressure with that m5 tip... the PW gun more or less looks like your soft wash rinse..

What GPM M5 is that you use for the x6?

Hey Ray could you send a link for the half inch swivel for the soft wash gun?

For the Pressure Washing side of the DN 10 ball valve is it supposed to be a quarter inch quick connect at the end not three eighths? My bad I was thinking the Quick connect from the hose was the same size as what you put on the gun never mind it’s a quarter inch. Thanks for the video bro.

Hello Mr Raimond, where can I get the 1/2 inch swiwel and the viton gun that you show in the video, thanks

I am new and looking to start a small part time business with hopes to build up enough clients to do this full time. I will be starting off with a small set up. But can that shift wash gun be set up to use on pressure washer to so soft washing or will I need a dedicated soft wash system?

where did you get your hoses at? i'm looking for a hose for my pressure washer and a hose for my soft wash, if you could help me out that would be awesome! looking at the cox reels now

Hey Ray, Just on the adapter after the ball valve, is there a reason you didn’t use a 3/8quick connect to 1/4 female thread? Instead of using that adapter piece? Or do you need it?

Quick question does the chemical damage the M5 for the soft wash gun

What's up with the 12v x model pump vid?

What size of outlets on pump ? 1/2 or 3/4

What truck you running? Is that a dually f350?

Do you think a pressure washing business is viable in a hot dry climate? I live in Arizona where it's fairly uncommon to see organic material growing on surfaces. Are there go to alternative services to offer in dryer climates?

Nice stuff, i like to use a female m22 treaded fitting to attach quick connect to ball vale, but i may try your way never know if you dont do it.

3:40 On the softwash side (parts list )

hey man where do you find those twist wires that you have on your truck that help hold things down? Ive seen them on skids before just havnt been able to find them in store.

Ray for that ball valve set up are all those fittings high pressure? What PSI do you run by the way, I see the DN10 is 3000. I am running a 4000 machine.

FINALLY A VIDEO!! Lol

😊

We have been doing the ball valve gun for about 4 years. It will save your wrist!

Can we get a link to the Viton O-rings please

M5 twist on soft wash.. What size for half inch hose and 5gpm 12v?

Every time I use a viton oring my male plug gets stuck in female quick connect. Any solution to this?

Can you put a link to that black and also where you got Thank you great video bro

Could you possibly get in contact with me and give me the parts list and where to buy from on the pressure wand you built??

everybody knows its the Joe Deery M5 Twist with the shooter tip common man lol :)

Mtm sgs35 your welcome

Just thought could use a lanyard for saftey with ball vale so can drop it lol not that i see me dropping it or doing it

Why not just use an open gun with a DN10? I’ve got 2 Suttner open guns that are at least 6 years old, and I’ve got one J Adams open gun that’s around 3 years old. You still get the benefit of having a gun, but you’re not constantly having to squeeze a trigger. After years and years in this business the arthritis in my hands is horrible. Switching to an open gun with a ball valve is a game changer. Also, Teflon tape is for rookies. Medium threadlock or pipe dope only.

What supply store do you shop at ?

I have a question that may not pertain to this setup video. Anyways, what do you do before hand on a house for windows that are not sealed well? This question is eating at me big dawg.

Can you put a link to your gun? Thanks

Are you still around brother? Would love to connect.

These parts are so hard to find.