The Best Quick Release Steering Wheel Setup | Works Bell

No video

The Best Quick Release Steering Wheel Setup | Works Bell | MR2 Spyder

Рет қаралды 5,653

Touge Time

Күн бұрын

Instagram: /
Installing a Works Bell Hub and Quick Release and Momo Prototipo
Please like, comment and subscribe!

Пікірлер: 43

@stanleybacklund5614 2 жыл бұрын

Ah the ancient language of JDM

@vizualmrs 2 жыл бұрын

Definitely getting this exact setup

@NeilVegetaDang 2 жыл бұрын

Staff over at NRG gonna be disliking this LOL. Great video!

@ABeans07 2 жыл бұрын

lmfao i thought i was having a stroke with that scotty k clip

@aeipee13 2 жыл бұрын

Scotty Kilmer 🤜🤛

@worldtravelerjon 2 жыл бұрын

Looks great! Will consider.

@touge2622 2 жыл бұрын

WOW!

@chadbyrd4895 2 жыл бұрын

Great work

@pop455rc 2 жыл бұрын

It looks so good

@christianherrero8053 2 жыл бұрын

nice i have the standard 537 hub on mine... thinking about getting a quick release to use with the standard hub to bring the wheel in close to me

@Echizen32kMedia 2 жыл бұрын

How did you like this setup? I am thinking about the same thing and currently have the 537 hub.

@christianherrero8053 2 жыл бұрын

@@Echizen32kMedia it’s great my only thing is that I’m short and sit close to the wheel and the closer you get the lower the wheel is to your body ..and my current seat setup is a little bit higher than stock . I think a shorty hub and a quick release would be the same length as the standard hub though

@Echizen32kMedia 2 жыл бұрын

@@christianherrero8053 Thank you sir! I will try the 537 first to see how it goes. Are you 5'6 or 5'7? I'm 5'10 so if we are the same height, I was thinking about something similar setup wise.

@johnfrank6341 7 ай бұрын

you went from stock wheel diameter to 300 to 350mm. Curious why switching back to larger wheel?

@zzwk24 2 жыл бұрын

Fudge, I wish i knew this sooner.

@molikeabossboss3857 3 ай бұрын

Hello quick question brother, can I use an nrg quick release with the bellworks hub ?

@xnanoo 2 жыл бұрын

2:17 lmao

@Cichlid_Visuals 2 жыл бұрын

REV UP YOUR ENGINES scotty would love the intro to this vid

@Apollo_s2k 2 жыл бұрын

Couldn’t stop laughing 😂

@taynguyen7969 Жыл бұрын

Hi I bought the works bell kit. I tried to wire the horn using the positive and negative wire from the clock spring but it doesn’t work. The horn only works if I wire the positive wire to the horn and then make a negative wire that grounds to one of the screws on the hub. This drains my battery though. Am I doing something wrong?

@DelinquentDJ 2 жыл бұрын

whens that Crooober sponsorship comin in

@WhyallaDojo 9 ай бұрын

What did you do with the airbag loop on the existing plug?

@danielksong 2 жыл бұрын

Curious, how is the ergonomics of reaching the windshield and turn signal stalks with the hub + quick release? Or do you think it's much more natural with just the hub?

@Cypress_green 2 жыл бұрын

You forgot to rev up your engines Scotty!

@RedlineRicer 2 жыл бұрын

Noice

@Mattcrockpot 2 жыл бұрын

350mm in the smol car?

@MR.TORRES_GARAGE 2 жыл бұрын

Please send me the link to where you ordered everything u used? I did a steering wheel change and had to put it all back to oem cause everything went crazy! This video made everything look so easy to do,thanks!!!

@TougeTime 2 жыл бұрын

It is mentioned in the video where I bought everything

@MyNguyen-du5gh 2 жыл бұрын

how did u depin the yellow connector? having a hard time getting the wires out

@TougeTime 2 жыл бұрын

There is a pin tool or u can just cut and hardwire it. There is a lock u unclip on the connector as well. It's off color yellow. Not the same as the rest of plug

@nickwagner2284 2 жыл бұрын

I'm curious, with this hub, do you need the extra thickness of the quick release? I have this hub for my 01 Spyder (not installed), but don't have a quick release. Will the steering wheel be too far from you/close to the dash without the quick release or some kind of spacer? Thanks!

@TougeTime 2 жыл бұрын

That's subjective so it's up to u. They sell spacers or u can get a dished wheel

@nickwagner2284 2 жыл бұрын

@@TougeTime Right, but any idea how close/far away your setup is compared to stock?

@nickkings2220 2 жыл бұрын

Instructions in JDM 🤣

@ovidiscool 2 жыл бұрын

im just tryna give an option to people that gives them these benefits without the price tag. why is comment getting deleted 🙃. NRG hub for FRS/BRZ and a dremel around where the clock spring protrudes. you get to keep horn and clock spring and it looks really clean when done.