The Best Way To Change Paddles And Scraper Bar On TORO 721E Snow Blower
Рет қаралды 58,815
3 жыл бұрынHello all on todays video I am showing you the easiest and best way I have found to change out the paddles and the scrapper bar on my Toro power clear 721 E. The tools needed for this job are as fallows
For changing the paddles the tools required are
1- set of replacement paddles from Toro
1- T-25 torx bit
1- socket driver
1- 7/16 inch wrench
1- 11mm socket
1- small piece of tape ( duck tape or equivalent)
And the tools required for the scrapper bar are
1- new scraper bar from toro
1- impact or socket driver
1- 1/2 inch wrench
1- 9/16 inch socket
PLEASE LIKE, COMMENT & SUBSCRIBE IF YOU ENJOIED IT!
Please SHARE this video with someone!
Instagram: / amidwestfamily
Business inquiries only- amidwestfamily@yahoo.com
Gear I use:
--------------------------------------------------------------------------------------
GoPro- amzn.to/3U21Gs2
Editing software- amzn.to/3gJXH5c
Small tripod- amzn.to/3gFwhxn
(Amazon affiliate links)
@manysaints 11 ай бұрын
Bought this for my small back deck in the Eastern Sierra. kzfaq.infoUgkxoHYZbq5g9fkcAtinlTqstNlje-UQkCHN We get A LOT of HEAVY snow so I was a bit skeptical but it was worth it! After the first storm of the year this has exceeded expectations! It throws snow very well, even 10-12” + that said the more it piles up the harder it is to maneuver the machine. It is exceptionally light weight and overall exactly what I was looking for. If you have a large amount of snow and a lot of area to clear, you may consider something with a drive engine to help maneuverability, but for decks, second stories, roofs etc, you can’t beat the light weight to great snow throwing ratio. Side note, the chute rotator is a bit flimsy and it initially didn’t seem to work, after a few uses it seems to have loosened up.
@amidwestfamily112 11 ай бұрын
I agree, it is a great machine!
@IronFist730 3 жыл бұрын
Outstanding. Those screws at the ends of the paddle are a pain. Especially on the drive belt side. The duct tape technique worked perfectly. Great tip.
@PuckHead00 3 жыл бұрын
Thank you *_so much_* for absolutely the best video on this topic! Your explanation and attention to detail is second-to-none (especially, regarding the orientation of the paddles). With much appreciation, and stay safe and well! 🍻
@amidwestfamily112 3 жыл бұрын
Thank you very much! It's nice knowing that the video was able to help people out! Thanks for watching!
@miker7378 Жыл бұрын
thanks for the tip with the tape made my job changing the paddles easy
@amidwestfamily112 Жыл бұрын
I am glad I was able to help, thank you for watching!
@johnvigil01 6 ай бұрын
Tape and wrench trick is a game changer with a ton of stuff! Great video, and thank you.
@akbaxb165 3 жыл бұрын
One of the best videos on this topic. Thanks for sharing your knowledge.
@amidwestfamily112 3 жыл бұрын
Thank you for watching and letting me know!
@wizdom705 2 жыл бұрын
I love the creativeness with the wrench, can tell you have done this a few times, thanks for the tips!
@amidwestfamily112 2 жыл бұрын
Thanks for watching! I hope it helped you!
@joebelliotti5104 2 жыл бұрын
So glad I found your video - your tips made this a much easier project than if I hadn't seen it!
@amidwestfamily112 2 жыл бұрын
I'm glad it was able to help you out! Thanks for watching!
@user-wd1ld6lz8c 6 ай бұрын
This was AWESOME! Gonna put these on this weekend with your help! Supposed to snow 6-10" in a couple days so perfect timing!
@sharonlindroth8836 3 жыл бұрын
Excellent video--Thank You Very Much! I have watched many and yours was the most informative.
@amidwestfamily112 3 жыл бұрын
Thank you for letting me know! It is nice knowing that it is helping people!
@andywestwood2972 Жыл бұрын
Thanks! Very helpful and clear, especially the tips about tape, paddle orientation and warming. Great ! ! !
@amidwestfamily112 Жыл бұрын
Glad it was helpful, thank you for the donation!
@stephendenagy3396 2 жыл бұрын
This was an excellent tutorial, esp mentioning wrench sizes! I found one REALLY useful tool for this job is needle-nose vice grips. Plus I used them to press the spacers into the paddle. And…great idea gor keeping blade warm. But, when Mr. Procrastinator (me!) had to do this during a blizzard…a HEAT GUN really helped. I think that would help even in warmer weather, since the softer rubber really makes the side screws much easier to align and drive.
@amidwestfamily112 2 жыл бұрын
Thank you! It's nice to know it helped someone! I have also used some long needle nose pliers those do help getting the nuts started. Nice idea using the heat gun to warm the paddles up. Thanks for watching and commenting!
@gardengrower7633 2 жыл бұрын
Very clear video. Thanks for taking the time to illustrate it all. I appreciate it.
@amidwestfamily112 2 жыл бұрын
I'm glad it helped you out!
@stevemittelman4068 3 жыл бұрын
You are one amazing instructor. Thank you so much.
@amidwestfamily112 3 жыл бұрын
Thanks for watching! I am happy I was able to help!
@shawnwhitney2216 2 жыл бұрын
Great video! Your tips and suggestions were BANG ON! Duct tape idea worked great! Thank you for sharing your video
@amidwestfamily112 2 жыл бұрын
Thank you! I'm glad the video helped, needle nose pliers also work decent if you can't find any tap. Thanks for watching!
@coryhobbs5386 2 жыл бұрын
Thanks watching your videos gave me the confidence to change the oil and paddle on my unit, went back watched again to get the details needed I’m blowing the same snow as u in the twin city’s
@amidwestfamily112 2 жыл бұрын
Glad they were able to help you out! Thanks for watching!
@garynoss818 3 жыл бұрын
Thanks! Great video! I used a small, thin Vice Grips to start the nuts.
@reinaldomedina1093 2 жыл бұрын
Just what I needed thanks so much man really appreciate it I was having a tough time with my snowblower
@amidwestfamily112 2 жыл бұрын
I'm glad the video was able to help you, thanks for watching!
@petevicente9236 Жыл бұрын
Just did mine! Thank you for the great video. This job was easy using it.
@amidwestfamily112 Жыл бұрын
Awesome I'm glad it went well, thank you for watching and commenting!
@waynethebarber1095 Жыл бұрын
What a great video! It was so nice to see the close in shots too. We could really see what you were talking about. I have this to do on mine plus the paddle cable. I think it will be a all in one shot for me. Thanks for a great video... A very nice job!!!
@amidwestfamily112 Жыл бұрын
Glad it was easily understandable, thank you for watching!
@bols82 Жыл бұрын
Thank you! Just knocked out my first ever paddle and scraper replacement on my 2010 210E in about an hour. They held up pretty well after 11 years of Minnesota winters ☃️
@amidwestfamily112 Жыл бұрын
Glad I was able to help you out! Hope you have a great season!
@leadnsteel1428 Жыл бұрын
I put some serrated metal pieces the ends and now it can clear out frozen snow at the end of the driveways.
@amidwestfamily112 Жыл бұрын
@@leadnsteel1428 sounds like that could be dangerous be careful!
@dennisjust3092 3 жыл бұрын
Outstanding video. Thank you.
@Luigi-pk8mk 3 жыл бұрын
when I do these I put the paddles on an old style radiator in our house to warm them up and hold the nut with a narrow jaw vicegrips for the hard to get at ones. Narrow jaw vicegrips will just fit in that narrow gap.
@outdoorstudios2022 Жыл бұрын
Thanks for the video Greg, keep them coming.
@amidwestfamily112 Жыл бұрын
Thank you, I try to get 1 or 2 videos out a week sometimes it works and sometimes it doesn't.
@whtsoxfan27 Жыл бұрын
Nice job! Love the duck tape trick, as I have done this in the past with my power clear and that is a B... Nice work, appreciate you!
@amidwestfamily112 Жыл бұрын
Thank you for the kind words, and thank you for watching!
@mrmozart1 2 жыл бұрын
NIce job. You are a good teacher. Thank you.
@amidwestfamily112 2 жыл бұрын
Thank you, and thank you for watching!
@JTB-- 6 ай бұрын
Great Video. Tape Trick is a real time and sanity saver. and removing the inserts is a huge reminder. I like using a few pint soup containers for the screws and bolts so they don't mixed up or get lost
@amidwestfamily112 6 ай бұрын
Glad you found it helpful, I usually use magnetic trays to hold hardware. Thank you for watching!
@TJ-ce8ji 8 ай бұрын
Great video, thanks for sharing your tips!
@amidwestfamily112 8 ай бұрын
Thank you for watching!
@mrsjohnson1743 7 ай бұрын
This was really helpful! Now I feel like I can do this😊 Thanks!
@amidwestfamily112 7 ай бұрын
I'm glad it was helpful, thank you for watching!
@outdoorstudios2022 Жыл бұрын
Greg thank you for the detailed instructions
@amidwestfamily112 Жыл бұрын
Thank you for watching!
@JamesJackson-qs9oz 7 ай бұрын
thank you very much ... Fantastic step by step!!!! I REALLY appreciate your sharing of your knowledge....
@amidwestfamily112 7 ай бұрын
Thank you! I'm glad you found it helpful!
@tgray8593 Жыл бұрын
Great video...well detailed and explained properly.
@amidwestfamily112 Жыл бұрын
Thank you very much!
@javiercastillo8577 3 жыл бұрын
Great video. Thank you!!
@MaxCam35mm 2 жыл бұрын
Well explained! Thank you! 👍
@amidwestfamily112 2 жыл бұрын
Thank you for watching!
@jeffbander316 6 ай бұрын
This is a great video! I really appreciate it. But I’m jealous of how easily you changed those difficult bolts near the drive! Even with the duct tape trip I found it extremely hard! But got it done. Thanks
@amidwestfamily112 5 ай бұрын
it is difficult for sure, it does get a little easier the more you do it though haha!
@Flyeasy441 3 жыл бұрын
Thank you for the excellent tips and thorough demonstration. I have the same 721E and have to change the clutch cable and belt as well. 3 yr old unit
@amidwestfamily112 3 жыл бұрын
Thanks for watching! Changing the belt isn't hard to do, I kind of go over it in another video! kzfaq.info/get/bejne/epd9dbd2zs2cnas.html
@amidwestfamily112 3 жыл бұрын
@@Flyeasy441 those are not to bad to do!
@Flyeasy441 3 жыл бұрын
@@amidwestfamily112 Thanks for the quick reply.
@tonylofu1970 3 жыл бұрын
I have a 621 daughter I'm having trouble with the Chute cable freezing up any suggestion anyone
@amidwestfamily112 3 жыл бұрын
@@tonylofu1970 I use a silicone spray in my 2 stage snowblower and have not had any problems. There are several brands just use one that says silicone on it. I usually do it before the first snow and when I get it ready for summer storage. Hope this helps!
@Metalbladelawncare 6 ай бұрын
The tape on the wrench........genius. Also realized I threw out the spacers and have been rocking the snow blower for years without them.
@amidwestfamily112 6 ай бұрын
Glad I could show you a different way of doing it. I feel like the metal inserts get thrown away often. Thank you for watching!
@brothertax 2 жыл бұрын
Spot on. Thanks man.
@amidwestfamily112 2 жыл бұрын
Thanks for watching, and commenting!
@d.r.buchanan2329 7 ай бұрын
Best video I’ve seen thanks
@amidwestfamily112 7 ай бұрын
Thank you, and thank you for watching!
@TomaszBudz 9 ай бұрын
Thanx for the instructional video...
@amidwestfamily112 9 ай бұрын
Thank you for watching!
@raynovess3965 Жыл бұрын
Thanks, excellent job!
@amidwestfamily112 Жыл бұрын
Thank you!
@glenatgoogle4393 3 жыл бұрын
Replaced paddles and scraper on a 221 model today. Paddles/rotor/scraper all look exactly the same as your video. It had T27 torx screws in the paddles. I used commercial grade paddles and they are slightly thicker and considerably stiffer (6 rayon? plies are visible). Tried the tape trick, still couldn't get the screw started. Finally wound up taking the entire rotor out of the housing so I could get after it on the bench. Fixed!! Next time I do this I'm going to try removing the "half-rotor" plates completely, attach the paddles at the ends (drive side first) then reattach the half-rotor plates. Don't know if that will work any better, but for what I had to pay the "cuss jar" today, it might save me some money ;-). Thanks for the vid "Family" !!
@amidwestfamily112 3 жыл бұрын
Sorry the tap trick didn't work. Some people like to use long needle nose pliers to hold the nut when they start. Hopefully you have a better experience next time! Thanks for watching!
@frankgraczyk6491 6 ай бұрын
I've used the tape trick to retain a nut before with success, but used a pair of needle nosed pliers in this case instead to start the nut. A six inch pair of vice grips with the extended reach is helpful as well for locally compressing the paddles and contributing to greater bolt protrusion.
@amidwestfamily112 5 ай бұрын
Vise grips work awesome!
@davidbaron6647 Жыл бұрын
GREAT GREAT VIDEO VERY HELPFUL
@amidwestfamily112 Жыл бұрын
Thank you! Glad it was helpful.
@halloweendisplaysnowdogfun9016 2 жыл бұрын
Thanks; very helpful video.
@amidwestfamily112 2 жыл бұрын
Thanks for watching, I'm glad it helped!
@guidoitaliano7722 2 жыл бұрын
Awesome vid buddy
@amidwestfamily112 2 жыл бұрын
Thanks!
@mrbison45rpm 2 жыл бұрын
Thanks! Great Video
@amidwestfamily112 2 жыл бұрын
Glad it could help, thanks for watching!
@mikebos4882 8 ай бұрын
Very helpful.
@amidwestfamily112 8 ай бұрын
Thank you, glad it was helpful!
@westsidewil 2 жыл бұрын
Thanks for the video
@amidwestfamily112 2 жыл бұрын
Thanks for watching!
@sniffiejoe9370 Жыл бұрын
thank you your the best
@amidwestfamily112 Жыл бұрын
Thank you for watching!
@jayk7781 2 жыл бұрын
I definitely appreciate tthe duct tape technique. Thank you
@amidwestfamily112 2 жыл бұрын
Long needle nose pliers work well also. Thanks for watching!
@outdoorstudios2022 Жыл бұрын
Catching up on your past videos
@amidwestfamily112 Жыл бұрын
Well thank you for doing that!
@EuroYardService 2 жыл бұрын
Great video...Tape idea is all I needed...was having some real grief with just needle nose pliers...nut kept falling off.
@amidwestfamily112 2 жыл бұрын
Thanks! I'm glad it was able to help you out! Thanks for watching!
@vickic8633 2 жыл бұрын
Interesting how they use an 11mm on the center paddle bolts, but everything else is standard. Duct tape good idea. Think I will try my needle nosed visegrips instead when I change mine. Great "how to video"! Have the 621 and haven't use it enough to change paddles yet. Use mostly the 2 stage last winter.
@amidwestfamily112 2 жыл бұрын
The needle nose visegrips work well also. Yeah idk why they use standard and metric hardware. Thanks for watching!
@waynesalekin6773 Жыл бұрын
Thanks!
@amidwestfamily112 Жыл бұрын
Thank you for watching!
@danielmota1095 Жыл бұрын
A year ago I almost shot that dam toro because of those paddles!!! GREAT TIPS
@amidwestfamily112 Жыл бұрын
Yeah I bet, thank you for watching!
@tomconnors6310 Жыл бұрын
I have a single stage blower with those paddles, it is that easy to replace and you should get about 2 winters on a set of paddles.
@amidwestfamily112 Жыл бұрын
Depending on how much snow you get I would agree. I haven't even pulled mine out yet from storage yet....
@jeffreysuper5236 2 жыл бұрын
Thanks.
@GrandmasterBeef Жыл бұрын
Thanks buddy, saved my ass in a couple of areas.
@amidwestfamily112 Жыл бұрын
Glad to hear I was able to help you make it an easier process for you!
@Moondog9322 2 жыл бұрын
Good idea with the duct tape. I use narrow jaw Vice Grips. Those end bolts are a pain.
@amidwestfamily112 2 жыл бұрын
Those work great also!
@roseadesjarlais5496 Жыл бұрын
Using the back of the truck looks like a great work bench…..
@amidwestfamily112 Жыл бұрын
It works well most of the time.
@outdoorstudios2022 Жыл бұрын
CrazyQuady Mike sent me over.
@amidwestfamily112 Жыл бұрын
Thank you for checking out the channel!
@scottkaiser8589 6 ай бұрын
I now see where I went wrong. I took off all the screws at once and everything took a piss. Should have done what you did one at a time. I like the truck with the duct tape too
@amidwestfamily112 5 ай бұрын
Glad the video was helpful!
@NEDERLAM 2 жыл бұрын
I used needle nose vice grips to hold paddle in place, and another needle nose vice grip to hold the nut.
@amidwestfamily112 2 жыл бұрын
Those work well also!
@alumiu 2 жыл бұрын
Thank you so much for your video. Do you recommend buying the standard paddle kit or the long life paddles? I only use the blower about three times a season, but it has lasted for 17 years. Put into service back in 2005 in South Bend and then brought down to St. Louis. Just now having to replace the paddles.
@amidwestfamily112 2 жыл бұрын
I just use the regular paddles, sounds like you got alot of use out of the standard paddles. Thanks for watching!
@got2getit204 Жыл бұрын
Get you a pair of needle nose pliers vice grips to hold that bolt for ya!
@amidwestfamily112 Жыл бұрын
Those work well also, thank you for watching!
@rayeckert9425 2 жыл бұрын
Pickup trucks beds make the perfect height workbench, I’ve been doing that for years.
@amidwestfamily112 2 жыл бұрын
Yes they do! Thanks for watching!
@rayeckert9425 2 жыл бұрын
@@amidwestfamily112 those Toros are such great snow blowers, I have five of them that I use in my business up here in the great white north eh.
@amidwestfamily112 2 жыл бұрын
@@rayeckert9425 I don't really have any complaints with the one I have, I would like to try the qze model but am afraid that the cables would freeze up. 🤔
@davidskowronski4010 Жыл бұрын
I would have NEVER thought of the duct tape on the wrench to hold the nut.
@amidwestfamily112 Жыл бұрын
You could also use long needle nose pliers. Thank you for watching!
@MrBluestreak1234 2 жыл бұрын
great video but please suggest to empty the oil before tilting the snow blower,,, it winds up leaking thru the carb??
@amidwestfamily112 2 жыл бұрын
Sounds like a good idea!
@ryanp5137 2 жыл бұрын
Great video! Can the 2 bolts and nuts be flipped?
@amidwestfamily112 2 жыл бұрын
No they cannot sadly
@johnfritz3792 5 ай бұрын
How often do you replace the belt?? I like the tape trick, I normally use needle vise grips
@amidwestfamily112 5 ай бұрын
I have had this unit over 5 years and have not needed to replace the belt yet. Vise grips work well also!
@joeserrenti9857 3 ай бұрын
Just a heads up ..... When I tipped mine back like that, started the repair at night, came down the next morning....all the oil had leaked up into the engine head , out of the muffler all over the floor .... massive repair ..... Don't tip it back unless you empty ALL of the oil and gas out.
@amidwestfamily112 2 ай бұрын
Sounds like a good thing to keep in mind, thank you for letting us know!
@fredberger3155 Жыл бұрын
Hey Midwest, I ran into a problem changing my paddles. I assembled all the tools; my torx t25 is the hand screwdriver type. Terrific so far. (As an aside, my tools are American made Challenger and Protool. But I found that the bolts don't really make a tight fit; they don't slip, but there's too much play). The big problem was the bolts at the ends of the paddles - they're torqued on so tight that no human can move them. I have the thicker paddles that came with the 721rc, could that make a difference? Those bolt heads are pulled tight into all that rubber. The only thing I can think of is that I have to cut the rubber away, maybe with tin snips; perhaps that will release some pressure from the bolts. I could spray with WD40, but I don't think it's soak in anywhere because of the rubber. Anybody have some suggestions? Thanks
@amidwestfamily112 Жыл бұрын
Yeah I don't think the thicker paddles would make that big of a difference. I haven't had that problem yet, I do make a point to change any hardware when doing a paddle swap if the bolts are starting to get bad or starting to strip out. Best of luck!
@Sjackson2369 3 жыл бұрын
Very good video. When I did mine, the paddles were hitting the back wall and killing the engine. Haven’t torn it apart to look if there is an adjustment yet.
@amidwestfamily112 3 жыл бұрын
As far as I know there is no adjustment on the paddles. Good luck!
@Sjackson2369 3 жыл бұрын
@@amidwestfamily112 lesson learned, double check your model and width. You’ll run into fitment issues trying to put 21” blades in a 20” machine.
@amidwestfamily112 3 жыл бұрын
@@Sjackson2369 oh man that's a bummer hopefully you were able to get it fixed easily without doing any damage!
@Sjackson2369 3 жыл бұрын
@@amidwestfamily112 since I couldn’t take the 21” paddles back, I modified them to fit, and I figure this will just give me more meat to wear through for the rest of this year. Bought the 20” paddles, looking for a new scraper edge for the housing for next year. No big deal.
@NEDERLAM 2 жыл бұрын
Important to reuse your old screw spacers from the center two holes.
@RonJ-en7in Жыл бұрын
Great video. Are you absolutely sure that the thicker side of the paddles face that direction? What happens if they're in backwards? Will it wear down faster or maybe not throw snow as far? I just picked up a used 621 qze and the paddles are facing the opposite direction. So I'm assuming someone changed them at some point and put them on wrong. We don't have snow yet, so I couldn't try it out. But they're worn down to the holes and need to be changed anyway. Going to make sure I put em on the way you did instead of how they are now. Thanks!
@amidwestfamily112 Жыл бұрын
Hello, yes the paddles should go the thicker side towards the machine. If they are installed backwards I would imagine they might wear out faster. But i dont know that since i have always installed them one way. Thank you for watching!
@RonJ-en7in Жыл бұрын
@@amidwestfamily112 Thank you so much! After my post, I saw Toro instructions that confirmed you are absolutely correct. 😀
@amidwestfamily112 Жыл бұрын
@@RonJ-en7in no problem!
@randybeck-kk1kg Жыл бұрын
Appreciate the video ! Have you ever come across an issue with newly installed paddles hitting the ground so much that the blower bounces along ? All the bolts are tight on the paddles, the paddles clear the scraper blade just fine ( which is also new ) but it seems like too much of the paddles hit the ground. I did buy this as a kit for the 721E ( part #’s match manual too ) off Amazon so maybe that’s the issue too 😅 Thanks !
@amidwestfamily112 Жыл бұрын
I have not had that problem, the only time it does a hoping or bouncing effect it's from snow buildup on the wheels. Good luck let us know what you find out!
@lifesaver3499 Жыл бұрын
Hi...can i grease my noisey auger bearings or do inhave to put on new ones? 25 year old machine
@amidwestfamily112 Жыл бұрын
I believe they are sealed bearings, so you would just have to replace it. That being said you could try to grease it, it wouldn't hurt anything.
@jmaxs77 Жыл бұрын
Great video. Now I dont have to pay a Toro dealer to do it anymore!
@amidwestfamily112 Жыл бұрын
Glad it helped, thank you for watching!
@jmaxs77 Жыл бұрын
@@amidwestfamily112 You were using a drill driver and a impact wrench ?
@amidwestfamily112 Жыл бұрын
@@jmaxs77 yes, you don't have to but if you have the power tools you might as well use them!
@jmaxs77 Жыл бұрын
@@amidwestfamily112 What size impact wrench are you using : 3/8 or 1/2 ? I'd like to get for this purpose.
@amidwestfamily112 Жыл бұрын
@@jmaxs77 I was using a 3/8s impact.
@TechBoner180 3 жыл бұрын
How long was the blower in use before the paddles needed to be changed
@amidwestfamily112 3 жыл бұрын
I usually get 2-3 seasons out of them and that is doing about 6 houses per snow event. Thanks for watching!
@TechBoner180 3 жыл бұрын
@@amidwestfamily112 Thank you. Your video and comment have been very helpful.
@amidwestfamily112 3 жыл бұрын
@@TechBoner180 glade I was able to help! Thanks for watching!
@JH-ze8dv Жыл бұрын
On a Toro 621, oil will leak out of the breather of the the unit if it is placed on it's back. Just keep the unit titled up at least a foot so it won't. Otherwise, awesome video!
@amidwestfamily112 Жыл бұрын
Thank you for the tip, I will be sure to make a note of that next time! Thank you for watching!
@akaCamo Жыл бұрын
Thanks for posting this .... I have a Toro 721QZE and got a bunch of oil in the pickup bed of the truck today. I was wondering where it came from since the oil dipstick was tight and didn't seem to be leaking. Next time I'll probably drain the oil first before I tilt the machine backwards.
@awomanwonderful 2 жыл бұрын
I see this was a year ago I’m a female I’ve just purchased my first gas machine I’m a senior citizen I’m all these things! the first use I noticed my paddle has some threads that are loose. I guess ripping through the snow is that normal and is it supposed to be on the ground is the paddle supposed to come in contact with the ground? I sure hope somebody answers this for me.
@amidwestfamily112 2 жыл бұрын
The rubber paddles are designed to contact the cement, so yes the strings hanging off the paddle is normal. Just pay attention to the wear indicators on the paddles and replace them when they are due. For my unit I change the scraper bar every other time I change the paddles. Thanks for watching!
@suohrom Жыл бұрын
I wasnt luck enough and the paddle screws would not come loose with that tork head. Used grinder to cut screws.
@amidwestfamily112 Жыл бұрын
Bummer, at least you have new hardware now!
@jamesmoreira3333 6 ай бұрын
R all paddles the same to buy for the 721e
@amidwestfamily112 5 ай бұрын
If you buy genuine Toro paddles they have two different options, the standard paddle or the HD paddle. The HD paddle is what comes standard on there commercial line like the 721 CR.
@lindabaird661 3 жыл бұрын
Did you use a 1" or 2" T-25 Torx Bit?
@amidwestfamily112 3 жыл бұрын
If you are using a drill or driver I would use the shortest bit you have.
@dfmackenzie 2 жыл бұрын
Yes, start the nuts just a little bit. Then tighten fully later. Otherwise it is impossible.
@amidwestfamily112 2 жыл бұрын
Agreed 1000% thanks for watching!
@ronzek3207 Жыл бұрын
Glad I watched this on scraper bar, was not sure how springs fit on the bar correctly. Thanks.
@amidwestfamily112 Жыл бұрын
Glad it helped you, thank you for watching!
@GordHerreman Жыл бұрын
Hi would like to know what type of rubber that is and the durometer it is thanks
@amidwestfamily112 Жыл бұрын
Sorry for the delayed response. I do not know exactly what the paddles are made of, some sort of reinforce rubber. I get the replacement paddles, belts, scraper bars and any other parts from my local toro dealer.
@GordHerreman Жыл бұрын
ok tks thought it was some kind of special rubber
@got2getit204 2 жыл бұрын
Why you didn’t just get the 721 rc and how long your paddles last?
@amidwestfamily112 2 жыл бұрын
I wanted the rc model but I could not find any in stock anywhere at the the time, this was the only model I could find. The paddles last around 70 houses depending on concrete conditions and such.
@sargonoshana2324 3 жыл бұрын
I put napkin on the nut. The problem was i couldn't screw the screw into it, because i left the paddles in the garage and they were not pliable. Such a pain. I should of left them in the house.
@thetraveler3739 Жыл бұрын
I have this same blower but every time I try to put the bolts on the sides that are hard to get at the paddle won’t line up with the hole there is a 1 inch gap and the paddle won’t budge either. Ugh I’m so frustrated.
@amidwestfamily112 Жыл бұрын
I have not had that problem. I start the bolts on the end that is hard then start the ones on the other end then the center ones. After they are all started I go back and tighten them down.
@billdomi9374 2 жыл бұрын
Sounds like Woody Harrelson.
@amidwestfamily112 2 жыл бұрын
Thank you! I will be sure to tell the wife that haha
@guidoftc8304 2 жыл бұрын
How did u know u had to change it they look ok to me
@amidwestfamily112 2 жыл бұрын
On most single stage units there will be a wear hole indicator on the paddles to let you know when they are in need of replacement. Once the hole is open or gone they are worn out. Or you can usually tell when the unit starts throwing snow in front of your path, instead of throwing it out the shoot.
@madcyborg 3 жыл бұрын
Good video man... while Your at it.....may as well change the spark plug and check the fuel lines to boot.
@amidwestfamily112 3 жыл бұрын
Thank you! I pulled the spark plug and did a look over on a maintenance video kzfaq.info/get/bejne/epd9dbd2zs2cnas.html thanks for watching!
@kh12productions Жыл бұрын
Hey man! Thanks for the videos, pick up the same snowblower used and it’s been a pain. Hardly throws any snow. Throws it barely out of the shoot and most of the time the snow falls back in and then it gets clogged making it pretty useless. I changed the belt out thinking that was the problem. Pulley was in good shape. Tested it again and same thing. Would replacing the paddles help with the issue do you think?
@amidwestfamily112 Жыл бұрын
I would check the wear marker on the paddles. Chances are the paddles and the scraper bar needs to be replaced.
@kh12productions Жыл бұрын
@@amidwestfamily112 awesome! I can’t even see the wear marks… so assuming they are worn bad. I’ll replace them and the scraper and will update you!
@amidwestfamily112 Жыл бұрын
@@kh12productions sounds good, good luck!
@isasakiri3679 3 жыл бұрын
Where can I find these parts?
@amidwestfamily112 3 жыл бұрын
I picked them up at one of my local toro dealers. Write down your model and serial number and they will be able to get you whatever parts you need!
@marks1034 2 жыл бұрын
Mine were rusted on and the heads stripped out on a few of them. Heat and PB blaster wouldn't loosen them. Had to cut them off.
@amidwestfamily112 2 жыл бұрын
Sounds like a pain in the butt!
@halloweendisplaysnowdogfun9016 2 жыл бұрын
What did you use to cut them? I have the same issue where one bolt stripped and I can’t loosen the nut.
@zzman5306 2 жыл бұрын
@@halloweendisplaysnowdogfun9016 Dremel tool with cutting discs
@MrRerod 10 ай бұрын
I cant even get the shoulders of the screws through the damn rubber
@JoyceMusick 7 ай бұрын
Thanks for the video. It was very helpful. But can you advise if the skid plate height can be adjusted? And is there somewhere to adjust the height of the blades so not to pull up gravel driveway?
@amidwestfamily112 7 ай бұрын
The single stage snow blowers typically do not have an adjustable scraper bar. They are designed mostly for concrete, if you want a adjustable hight scraper bar those are usually on the 2 stage units.
@roseadesjarlais5496 Жыл бұрын
I notice the bolts are not metric???
@amidwestfamily112 Жыл бұрын
I gravitate towards metric tools, I try those before I try the standard stuff. They vary well could be all standard. Thank you for letting me know!
@thomasrivest5843 2 жыл бұрын
I hate to admit it I put mine on wrong lol
@amidwestfamily112 2 жыл бұрын
It happens..... haha
FIX Tech Guides
Рет қаралды 230 М.
AnythingAlexia
Рет қаралды 14 МЛН
Captain Kleeman
Рет қаралды 53 М.
FIX IT Home Improvement Channel
Рет қаралды 149 М.
KB's Small Engine Repair
Рет қаралды 28 М.