The BEST way to get the MOST useful HORSEPOWER out of your ATV or Side by Side!!

Рет қаралды 16,546

Күн бұрын

Upgraded clutches are the way to go when it comes to putting the most horsepower from your machine to the ground. No one does it better than QSC and STM! I personally got a little taste of both worlds and will be doing some extreme testing in the near future. Here is a step by step tutorial on how to install a primary and secondary clutch.

Пікірлер: 45

@Budgetcaraudio 2 жыл бұрын

Boggs was litt you should on videoed us though we sunk 3 four-wheelers and we had 7

@ReneGabe_ 2 жыл бұрын

Dangggg I never saw y’all

@GG.Johnnie 2 ай бұрын

What’s the difference between the primary clutches I have seen stm 3p, wax rev x and 3rs ?

@levibalazs3775 2 жыл бұрын

any update on the boggs videos from the halloween ride?, marcos jeep crew checking in lol

@ReneGabe_ 2 жыл бұрын

They’re both posted

@ProjectVengeance 2 жыл бұрын

curious what your rpms is at now when you are wide open throttle.

@ReneGabe_ 2 жыл бұрын

I’ll test it out soon

@user-st3ef6ur1y 2 жыл бұрын

👍👍👍

@ReneGabe_ 2 жыл бұрын

💪

@beri232 2 жыл бұрын

So what’s the difference between that RMT vs the Rev X HD which was supposedly made for side by sides with high hp

@ReneGabe_ 2 жыл бұрын

No clue honestly

@meridianmuddaddicts4905 2 жыл бұрын

wats the part number for tht maverick belt. im gunna run one on my 2021 rene

@ReneGabe_ 2 жыл бұрын

422280364

@tylerharbour8562 Жыл бұрын

What color primary spring is in yours? if you don’t mind me asking

@ReneGabe_ Жыл бұрын

I can’t even remember. Thought it was somewhere in that video

@cb_jay9226 Ай бұрын

What did you do with the 3 red little gaskets that comes on the stm belt screw ?

@ReneGabe_ Ай бұрын

Left them in the bag

@seanpair1382 2 жыл бұрын

With my STM primary they recommended I lapped the end of the crank. Did they recommend that with QSC?

@ReneGabe_ 2 жыл бұрын

If they did I didn’t see it anywhere

@deeaikens9843 2 жыл бұрын

Yeah I heard a lot about the primary Gettin stuck to the crank

@B1ou1nsGarage 2 жыл бұрын

where did you order both from?

@ReneGabe_ 2 жыл бұрын

Adam shumaker at qsc

@kregankordsmeier9407 Жыл бұрын

Is it the stm secondary that’s responsible for your engagement going from 2600 to 1300rpms?

@ReneGabe_ Жыл бұрын

No engagement deals primarily with the spring on the primary clutch

@kregankordsmeier9407 Жыл бұрын

@@ReneGabe_ oh ok see I have cvtech primary stock secondary and there’s a significant lag in the throttle until ab 2600rpm then it jolts hard

@lifewithflex4471 Жыл бұрын

@@kregankordsmeier9407 did u make any changes?

@nathanduenas442 3 ай бұрын

Can you use that same clutch set on a outlander

@ReneGabe_ 3 ай бұрын

Yes

@kennethkirbow93 9 ай бұрын

Is that the 570 ?????

@BlaiznTrails_Performance 2 жыл бұрын

What helix is in the stm?

@ReneGabe_ 2 жыл бұрын

Ummm not sure. It’s the one with engine brake I know

@johnnyjones549 2 жыл бұрын

Who did you order the qsc fro

@ReneGabe_ 2 жыл бұрын

Adam schumaker

@johnnyjones549 2 жыл бұрын

@@ReneGabe_ thank you

@jreca Жыл бұрын

Why did you choose that combo?

@ReneGabe_ Жыл бұрын

I heard it was nasty and they were right💪

@jreca Жыл бұрын

@@ReneGabe_ did they come already setup with the proper weights and springs for your bike? Where did you order them from?

@jammils38 2 жыл бұрын

No lapping compound? You not even going to lapping it 25 turns? I thought that was a necessary thing to do with a new primary.

@ReneGabe_ 2 жыл бұрын

I have never heard that before or seen it done but that doesn’t mean it’s not true.

@jammils38 2 жыл бұрын

@@ReneGabe_ that was what I was taught to do. And stm required it for theirs. But if you have not had any problems then maybe it's just a matter of preference?

@ReneGabe_ 2 жыл бұрын

@@jammils38 I honestly don’t know but I’ve never heard that but I’ve never owned an stm primary either