We did these repairs in the military. We drilled a screw in the center after we filed it down. Then we did the mold over the screw. It added an anchor ⚓️ for the new post. I agree , that will probably pop off.

My battery failed in a similar fashion, I fixed it with my Costco card

Говорят, если перевернуть табурет, то на него можно посадить четырёх лайфхакеров

Extraordinary. Heat up the sawed off post with an open flame torch melting the plastic of the case , then improperly solder a new stud in place so it can break off in 3 seconds. Follow this guy for more mechanical tips. Bravo.

Pro-tip. Always use a spark emitting power tool around leaky battery gases for a send-off worthy of never needing a battery for anything ever again.

Thanks for reminding me I need to make a dentist appointment

Here in the US you can just screw the stud out and replace it. Costs about 3$. Breathing that lead dust when grinding, priceless.

Always cool to see problems solved in ways they didn't need to be solved. 😂

Without it being physically attached to the center post it's just gonna pop off

Hey 👋🏾 auto zone has a lifetime warranty 😂😂

An elderly neighbor once put a battery charger on his battery in his car, spark ignited the gas, and BOOOOM! Only the 2 cables remained, one piece of that battery had dented the hood upward almost going through it, acid covered the old guy, but he was not injured. Big lesson learned back then!

Берешь графитный стержень от батарейки,цепляешь провод на него .провод на противоположную клемму,а сломанную паяешь.всё в дороге делается легко😉

At that point I would think “ima go buy a new battery”

open flame and a battery containing explosive gas; brilliant

Very dangerous having a open flame around a battery.

Делается не так совсем. Берешь графитовый электрод, ставишь форму и плавишь самим же аккумулятором, иначе свинец у тебя не сварится в том месте где ты его наливал.

Open flame near hydrogen gas cloud- SUPER GENIUS

Parts stores sell terminal sleeves that go on the posts. Just tap them on and attach the clamps. Cost around $5.

Ставишь форму, и графитовым стержнем подключенным ко второй клемме наплавляешь плюмбум(свинец) добавляя кусочки, это ещë в старые времена так делали👍

Вообще то для этого используем графитовый электрод. От огня бывает взрывается. 😊 Болгарка вообще не используется, электрод хорошо и так прогреет в глубину, для соединения.

Bro is hitting everyone with the automated customer service “thanks for watching”

Я еще лет 30 назад, скручивал из жестяной банки оправку. Ножницами вырезать легко. Потом брал угольный электрод из батарейки, и с помощью самого акб и кусочков дополнительного свинца расправлял остатки клеммы и формировал новую. И это прямо на трассе! Всем удачи.

El fundir el plomo con el soplete puede provocar la explosión de los vapores del electrolito 😮😢

Why did this give me sooooomuch satisfaction.........cause I had a battery that had a shit lead and I only wished I could to this to it

If that terminal looked like that the battery wasnt gonna last too much longer anyway

"Thats great but my battery is still dead!"

Best way to inhale lead I’ve seen yet!

When Michael Jackson joined the army,they all ran the "Curyhehe".

Cool video , the new terminal looks like it would easily snap off

You are crazy for using an open flame around a car battery. I have personally seen what some sparks will do blew up in my father's face cutting him and had acid burns. To the ER he went.

Some people are saying it's connected... It's not. There is no chemical bond between top and bottom layers. It's pretty much like putting wet Play-Doh over dry Play-Doh.

As a mechanic having done a few similar things in my time,I stripped the lead back and used a screw to make an anchor point for the new lead to grab on to. This would snap off very quickly in my opinion as it has nothing to properly bond to other than the base lead…lead is very soft and the screw is steel giving it some strength.

У меня было много аккумуляторов, но вот таких убитых клемм не было ни разу!!!!!! Как такое возможно !!!!!??????

Respect to these type of people that make your battery for a living!

Это как можно так довести акб до такого состояния? 😮

This seems mildly comfortable to watch

My teacher in ROP regional occupational program, was a good old boy he was a cigar chomping dude he leaned over a battery that was charging and it blew up in his face he was wearing safety glasses so he felt his was way along the wall to the faucet turned it on and stuck his head under it, well Ed turned out to be okay, one of the best things he ever taught me was "you got to eliminate the problem systematically" oh,and when working on batteries never smoke cigars or use a torch.

Во внутрь надо еще засверлиться. Потом заливку выполнять.

I am amazed that with the caps removed and an open flame above the battery, it didn't explode.

My battery terminal is covered with copper coils you find in wires. Wrapped it so much now clip can be tightened 😂😂

That's how you erase your past😅

Nice idea, but I would leave part of the piece to be stronger.

Век живи век учись перед пайкой клемы саморез в клемму вкручивал

Много возни, берешь угольный стержень, сердечник от старой батарейки, кусок провода , форму клеммы и кусочек свинца. Зачищаешь клемму, ставишь форму, соединяешь провод к другой клемме АКБ, ко второму концу провода цепляешь угольный стержень, предварительно заточенный. Угольным стержнем расплавляешь свинец в форме и добавляешь не достающую часть свинца. Клемма готова

Надо было саморез выкрутить либо до конца не дорезать, контакт может оторваться.

Оно не будет держаться.

That’s pretty darn dope!

I love how chewy lead looks. 😍

Lucky battery didn’t catch on fire and explode 😂

При открытых пробках открытое пламя самое то😂

That's how a battery blows up in your face

man this is really satisfying

Может уже пора просто аккум поменять, а не херню городить?

A naked flame on a battery… boom 💥

Это называется , мартышкин труд 😊

Make sure you blowout the cells before using torch. I used to rebuild forklift batteries and made my own cables and lead ends.

You better make sure that battery wasn't just charged doing that unless you want a big boom!

Gives a whole new meaning to; get the lead out 😂

Good job 👍👏

If this costs more than $200 I'm just going to buy another battery 😂

Очень не надолго, оторвется!

Я в армии коротким замыканием восстанавливал клеммы аккумулятора. Без всяких горелок и т п.

How about just putting that mold over the old post and melting that to shape? Didn’t need to do all that cutting and now the new one is going to break off at some point.

Аккумуляторщик при мне разбирал аккумулятор полностью, менял пластины, заливал электролит, запаивал. Все работало.

gotta love doing shit the hard way. it’s not like u can get a new one from the store and pull the old one out to replace it.

A lot of folks take "first world" for granted. If it can be fixed, fix it. Yeah, somr things may not be worth the hassle or risk, but honestly lots of folks dont understand how things work anyway and even if this isnt ideal its cool that humans find a way. They'll say "it has a finite life then needs replaced".... sure... but if you understand batteries and the specific type, you can repair/renew *anything* Drain it (preferably into your local communal water source, in these types of places 😂) and figure out how to clean off the inner plates through electolysis or whatever. Replace the terminals if needed. Add fresh electrolyte solution. Boom.

Ever seen a battery blow up??? Beeeautiful blue ball of fire.

In Florida, most batteries don’t last long enough for this to happen.

In America we just buy a new battery!

Im buying a new battery to save that 30 minutes of life lol

Your working method is very good and effective

My method is to use the right tools in the first place, and my terminals outlive the battery. It's been working for half a century.

use a hand saw, with the machine you're breathing a lot of the lead into your lungs brother, be safe

В82 г акумуляторщик делал это за 10 минут😅

That's going to pop off guaranteed.

Я делал проще: сначала так же как на видео срезал старую клемму, затем напильником вытачивал новую заготовку из свинца. Потом соединял её тонким проводом со второй клеммой, которая на аккумуляторе. Далее - методом дуговой электросварки: подносил клемму к месту её установки, выдерживая при этом нужный зазор, чтобы происходила электродуга, и плавился свинец. Оставалось только выдержать клемму в вертикальном положении в нужный момент, и всё. Ну и потом только подровнять шов напильником по кругу, и всё готово. Всем удачи и смекалки))

It’s important to inhale deeply when grinding and working around melted lead.

Как сильно надо насиловать акб что бы довести клеммы до такого состояния

I used to recondition batteries for a battery company. When the battery was good and it wasn't very old. We would make it look like new again. We would paint them and put new posts on them. The new post I would put on would be As strong as the original post. I probably did over a thousand of them

He's replaced the battery head more than a hundred times now😂😂😂

There ,you go . One ruined battery😂😂😂

Как правило аккамулятор накрывается быстрее чем эти контакты! Это что нужно делать что бы так их испортить

I replaced my car battery with 80 bucks...

Looks like a cold solder joint. Will break off easily

炙っても周りのプラスチックって溶けないの？

Yo no la huviera cortado , huviera limpiado lo malo y la huviera fundido

Using a ginder on lead is horrific on your long term health. Alzheimer's, shakes, anger, memory loss anyone?

Tell me you're stupid without telling me you're stupid. 😂

Before you pour the lead, close a screw on the part you cut, then pour the lead

Who actually does work like this? This is pretty amazing.

The original was perfectly fine it will still take a clamp

Must be a very good battery to do all this to save it!

もうこの状態になったら新しいバッテリー買いなよ…

Why wouldn't you just screw the stud out? I swear DIY videos are Chinese and Indian psyops to ruin your cars.

CAL-OSHA shuts down your work site, then leaves the chat.

My dad just rolled over in his grave after I watched this..

Уважаемые почему всё путаете клеммы с выводами

I am 62 and NEVER have I had a bad post on a battery, now the clamp that’s another video😂😂

That was awesome. I wish I knew that last week.

Mi abuelo tenía una fabrica de acumuladores. Es así como se fabrican los terminales: un molde, se derrite la base de plomo con el soplete, y se rellena con plomo el molde. El agua fría es sólo para acelerar el proceso. Y es importante que cada vaso esté destapado